User's Manual
Table Of Contents
- VX 675
- Contents
- Preface
- Terminal Overview
- Terminal Setup
- Selecting Terminal Location
- Unpacking the Shipping Carton
- Examining Terminal Features
- Examining Connection Ports
- Installing the Paper Roll
- Installing the SIM Card
- Installing the SD Card
- Using the Battery
- Battery Behavior (No Power Pack)
- Connecting the Terminal Power Pack
- Charging the Battery
- Using the VX 675 Base Stations
- Powering Up the Base
- Docking the Terminal on the Base
- Undocking the Terminal from the Base
- Conducting Wireless Transactions
- Conducting Smart Card Transactions
- Using the Magnetic Card Reader
- Connecting to USB Host
- VX 675 ECR (Fiscal Module) Support
- VX 675 3G and GPS Support
- Using the Terminal Keys
- Verix Terminal Manager
- File Authentication
- Performing Downloads
- Downloads and Uploads
- Download Methods
- Download Tools
- Download Content
- Full and Partial Downloads
- Support for Multiple Applications
- Use of I: drive and F: drive
- File Authentication Requirements
- Required Certificates and Signature Files
- The File Authentication Process During an Application Download
- File Group Permissions
- Download an Operating System Update Provided by VeriFone
- File Authentication for Back-to-Back Application Downloads
- Timing Considerations Due to the Authentication Process
- Support for File Compression
- Effect of Downloads on Existing Files and Data
- Direct Operating System Downloads
- Back-to-Back Application Downloads
- Specifications
- Maintenance
- VeriFone Service and Support
- System Messages
- Troubleshooting Guidelines
- Port Pinouts
- ASCII Table
- VX 675 Battery Information
- Glossary
- Application ID
- Application program
- Application prompt
- ASCII
- Back-to-back application download
- Baud
- Bit
- Block
- Boot loader
- Buffer
- Byte
- Calendar/clock chip
- Card reader
- Carrier
- Certificate
- Character
- CONFIG.SYS file
- CPU
- Data
- Data entry
- Data packet
- Default
- Delete
- Diagnostics
- Direct download
- Display
- Download
- File authentication
- Firmware
- Fixed prompt
- Flash memory
- Host computer
- Input
- Interface
- Keyed file character set
- Keyed file editor
- Keyed file record
- Keypad
- Local functions
- Manual transaction
- Memory
- Messages
- Non-volatile memory
- Normal Mode
- Packet
- Packet-switched networks
- Parameter
- Password
- PC
- Peripheral terminal
- Port
- POS terminal
- Power pack
- Prompt
- Protocol
- PTID
- RAM
- Remote host computer
- Scroll
- Search key
- Serial port
- Signature file
- mDRAM
- Subroutine
- Swipe
- Verix Terminal Manager
- Verix Terminal Manager password
- Terminal
- Terminal ID
- Terminal-to-terminal application upload
- Track 1, 2, or 3 data
- Transaction
- Variable
- Volatile memory
- Index
- Contact VeriFone
TERMINAL SETUP
Conducting Smart Card Transactions
VX 675 R
EFERENCE GUIDE 29
Conducting
Smart Card
Transactions
The smart card transaction procedure may vary from one application to another.
Verify the procedure with your application provider before performing a smart card
transaction.
To Conduct a Smart
Card Transaction
1 Position a smart card with the contacts facing upward (see illustration below).
2 Insert the smart card into the smart card reader slot in a smooth, continuous
motion until it seats firmly.
3 Remove the card only when the application indicates the transaction is
complete.
Figure 17 Inserting a Smart Card
Using the
Magnetic Card
Reader
The VX 675 terminal supports credit/debit card transactions.
To Conduct a Credit
or Debit Card
Transaction
1 Position a magnetic card with the stripe in the card reader and facing inward,
toward the keypad.
2 To ensure a proper read of the magnetic swipe card, the user should insert the
magnetic card from the top of the unit, as shown in the following illustration.
CAUTION
Do not remove the smart card in the card reader until the transaction is complete.
Premature card removal will invalidate the transaction.