User's Manual
Table Of Contents
- VX 675
- Contents
- Preface
- Terminal Overview
- Terminal Setup
- Selecting Terminal Location
- Unpacking the Shipping Carton
- Examining Terminal Features
- Examining Connection Ports
- Installing the Paper Roll
- Installing the SIM Card
- Installing the SD Card
- Using the Battery
- Battery Behavior (No Power Pack)
- Connecting the Terminal Power Pack
- Charging the Battery
- Using the VX 675 Base Stations
- Powering Up the Base
- Docking the Terminal on the Base
- Undocking the Terminal from the Base
- Conducting Wireless Transactions
- Conducting Smart Card Transactions
- Using the Magnetic Card Reader
- Connecting to USB Host
- VX 675 ECR (Fiscal Module) Support
- VX 675 3G and GPS Support
- Using the Terminal Keys
- Verix Terminal Manager
- File Authentication
- Performing Downloads
- Downloads and Uploads
- Download Methods
- Download Tools
- Download Content
- Full and Partial Downloads
- Support for Multiple Applications
- Use of I: drive and F: drive
- File Authentication Requirements
- Required Certificates and Signature Files
- The File Authentication Process During an Application Download
- File Group Permissions
- Download an Operating System Update Provided by VeriFone
- File Authentication for Back-to-Back Application Downloads
- Timing Considerations Due to the Authentication Process
- Support for File Compression
- Effect of Downloads on Existing Files and Data
- Direct Operating System Downloads
- Back-to-Back Application Downloads
- Specifications
- Maintenance
- VeriFone Service and Support
- System Messages
- Troubleshooting Guidelines
- Port Pinouts
- ASCII Table
- VX 675 Battery Information
- Glossary
- Application ID
- Application program
- Application prompt
- ASCII
- Back-to-back application download
- Baud
- Bit
- Block
- Boot loader
- Buffer
- Byte
- Calendar/clock chip
- Card reader
- Carrier
- Certificate
- Character
- CONFIG.SYS file
- CPU
- Data
- Data entry
- Data packet
- Default
- Delete
- Diagnostics
- Direct download
- Display
- Download
- File authentication
- Firmware
- Fixed prompt
- Flash memory
- Host computer
- Input
- Interface
- Keyed file character set
- Keyed file editor
- Keyed file record
- Keypad
- Local functions
- Manual transaction
- Memory
- Messages
- Non-volatile memory
- Normal Mode
- Packet
- Packet-switched networks
- Parameter
- Password
- PC
- Peripheral terminal
- Port
- POS terminal
- Power pack
- Prompt
- Protocol
- PTID
- RAM
- Remote host computer
- Scroll
- Search key
- Serial port
- Signature file
- mDRAM
- Subroutine
- Swipe
- Verix Terminal Manager
- Verix Terminal Manager password
- Terminal
- Terminal ID
- Terminal-to-terminal application upload
- Track 1, 2, or 3 data
- Transaction
- Variable
- Volatile memory
- Index
- Contact VeriFone
TERMINAL SETUP
VX 675 ECR (Fiscal Module) Support
VX 675 R
EFERENCE GUIDE 31
VX 675 ECR
(Fiscal Module)
Support
The fiscal module allows ECRs to have direct connection to the Ministry of
Finance servers. When a mobile transaction is made, the transaction data is sent
over to the Ministry of Finance servers, and then goes to the banking host system.
The fiscal module stores the transaction data (up to 2 MB). A metallic seal is
placed on the right side, under the MSR to secure the fiscal module.
Customer Display
A 42mm single line customer-facing display (no backlight) that can display up to 8
characters including “,” or “.” between any character. It is located below the paper
roll cover.
Figure 20 VX 675 ECR Customer Display
VX 675 3G and
GPS Support
VX 675 3G uses the Cinterion PHS8-P radio module that incorporates 3G High-
Speed Packet Access (HSPA+) connectivity. The PHS8-P radio module is
optimized for high bandwidth and allows a downlink speed of 14.4 Mbps and an
uplink speed of 5.7 Mbps.
GPS Receiver
The Cinterion PHS8-P radio module integrates a GPS receiver that offers the full
performance of GPS/A-GPS technology.
Connecting by 3G
To connect to existing 3G operator-provided infrastructure, check that SIM has
been inserted, see Installing the SIM Card.