User's Manual
Table Of Contents
- VX 675
- Contents
- Preface
- Terminal Overview
- Terminal Setup
- Selecting Terminal Location
- Unpacking the Shipping Carton
- Examining Terminal Features
- Examining Connection Ports
- Installing the Paper Roll
- Installing the SIM Card
- Installing the SD Card
- Using the Battery
- Battery Behavior (No Power Pack)
- Connecting the Terminal Power Pack
- Charging the Battery
- Using the VX 675 Base Stations
- Powering Up the Base
- Docking the Terminal on the Base
- Undocking the Terminal from the Base
- Conducting Wireless Transactions
- Conducting Smart Card Transactions
- Using the Magnetic Card Reader
- Connecting to USB Host
- VX 675 ECR (Fiscal Module) Support
- VX 675 3G and GPS Support
- Using the Terminal Keys
- Verix Terminal Manager
- File Authentication
- Performing Downloads
- Downloads and Uploads
- Download Methods
- Download Tools
- Download Content
- Full and Partial Downloads
- Support for Multiple Applications
- Use of I: drive and F: drive
- File Authentication Requirements
- Required Certificates and Signature Files
- The File Authentication Process During an Application Download
- File Group Permissions
- Download an Operating System Update Provided by VeriFone
- File Authentication for Back-to-Back Application Downloads
- Timing Considerations Due to the Authentication Process
- Support for File Compression
- Effect of Downloads on Existing Files and Data
- Direct Operating System Downloads
- Back-to-Back Application Downloads
- Specifications
- Maintenance
- VeriFone Service and Support
- System Messages
- Troubleshooting Guidelines
- Port Pinouts
- ASCII Table
- VX 675 Battery Information
- Glossary
- Application ID
- Application program
- Application prompt
- ASCII
- Back-to-back application download
- Baud
- Bit
- Block
- Boot loader
- Buffer
- Byte
- Calendar/clock chip
- Card reader
- Carrier
- Certificate
- Character
- CONFIG.SYS file
- CPU
- Data
- Data entry
- Data packet
- Default
- Delete
- Diagnostics
- Direct download
- Display
- Download
- File authentication
- Firmware
- Fixed prompt
- Flash memory
- Host computer
- Input
- Interface
- Keyed file character set
- Keyed file editor
- Keyed file record
- Keypad
- Local functions
- Manual transaction
- Memory
- Messages
- Non-volatile memory
- Normal Mode
- Packet
- Packet-switched networks
- Parameter
- Password
- PC
- Peripheral terminal
- Port
- POS terminal
- Power pack
- Prompt
- Protocol
- PTID
- RAM
- Remote host computer
- Scroll
- Search key
- Serial port
- Signature file
- mDRAM
- Subroutine
- Swipe
- Verix Terminal Manager
- Verix Terminal Manager password
- Terminal
- Terminal ID
- Terminal-to-terminal application upload
- Track 1, 2, or 3 data
- Transaction
- Variable
- Volatile memory
- Index
- Contact VeriFone
VERIX TERMINAL MANAGER
Verix Terminal Manager Menus
72 VX 675 REFERENCE GUIDE
5> KEY MANAGEMENT 1> IPP KEY LOAD
VERIX TERMINAL MGR
Please enter
Password for GID nn
___________________
Enter the current password for the selected
file group and press
ENTER.
Note: This requires group 1 privileges
and the group 1 password.
If you enter an incorrect password,
PLEASE TRY AGAIN appears. Press
ENTER. Verify your password and reenter it.
INTERNAL PIN PAD
KEY LOADING MODE
BYTES SENT 0
BYTES RCVD 0
Press 1 to END
Select this mode when you use the
SecureKit or programming from your PC to
inject keys into your terminal. In this mode,
a pass-through connection is established
between COM1 and COM5 (IPP port) to
allow key loading.
Press CANCEL to stop the key load
session; Press 1 to END when finished with
the key load.
Note: The connection times out after a
minute if the key loading does not
start.
5> KEY MANAGEMENT 2> RKL KEY LOAD
VERIX TERMINAL MGR
Please enter
Password for GID nn
___________________
Enter the current password for the selected
file group and press
ENTER.
If you enter an incorrect password,
PLEASE TRY AGAIN appears. Press
ENTER. Verify your password and reenter it.
Table 6 Verix Terminal Manager Menu 2 (continued)
Display Action