VD03
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Thank you for purchasing the Heritage™ Natural Spectrum® Deluxe Desk Lamp. Please read the following safety information before using. To reduce the risk of fire, electrical shock, or injury to persons: • • • • • Do NOT dismantle. Do NOT alter power cord. Turn off/unplug and allow to cool before replacing bulb or cleaning. For indoor use only. The lamp is an electrical device.
GETTING STARTED Main Parts & Controls A. Lamp Head G. Vertical Shaft B. Switch H. Lamp Base C. Lamp Head Swivel Knob I. Power Cord D. Lamp Arm J. Power Supply (Ballast) E. Center Swivel Knob K. Optix® Glare Control Filter F. Counter Weight Arm L.
ASSEMBLY INSTRUCTIONS Please Read Operating Instructions Carefully Before Using the Heritage™ Desk Lamp: 1. Set lamp base on the desk and insert the counter weight arm (F) onto the center swivel (E) and screw clockwise to tighten. (Fig.1) 2. To lift lamp head, loosen swivel knob (C), adjust head to desired angle. Tighten swivel knob. 3. Attaching the Optix® glare control filter: • Remove glare control filter from protective plastic bag. Take care to hold filter by the edges only.
ASSEMBLY INSTRUCTIONS cont. 4. Attach the ballast to the power cord. Use care to align the 4-pin plug properly. DO NOT FORCE – the 4-pin plug was designed to fit in only one orientation. (Fig. 3) Fig. 3 5. Plug ballast into a standard 120V 50/60Hz outlet. Turn lamp on. The green LED indicator on center of the ballast should be illuminated. (Fig. 4) If the LED indicator does not illuminate, please refer to the troubleshooting section of this manual. (See page 9) 6.
ADJUSTING THE HERITAGE DESK LAMP The Heritage™ Desk Lamp adjusts several ways: D E 1. To adjust lamp height – hold lamp arm with one hand, loosen center swivel knob (E). Raise or lower lamp arm (D) to desired height. Tighten knob. (Fig. 5) Fig.5 Swivel Knob 2. To adjust lamp head angle up or down – loosen swivel knob counterclockwise, place head at desired angle, tighten swivel knob to secure. (Fig. 6) Fig. 6 3. To tilt lamp head toward you or away from you – simply move head to desired position. (Fig.
BULB REPLACEMENT INSTRUCTIONS Removal 1. Unplug lamp from power source. 2. To access the bulb, remove Optix® glare control filter by depressing the thumb tab and lifting it out. 3. Firmly hold bulb base (B) and pull bulb (C) from the socket (A) in an outward motion. (Fig. 8) Installation 1. Unplug lamp from power source. 2. Firmly hold base (B) and push bulb (C) into the socket (A). 3. Be sure bulb is firmly seated in the socket (see below) and snapped into the metal bulb clip (D). (Fig. 9) 4.
TROUBLESHOOTING Your Verilux® desk lamp uses advanced micro-electronics to power the revolutionary Trucolite™ bulb. These electronics are housed in a specially designed ballast located at the power plug. The LED indicator light on the ballast allows you to troubleshoot any problems with the lamp’s function. When replacing your Verilux® ballast, take care to plug in the power cord properly. The 4-pin plug was designed to fit in only one orientation (See Assembly Instructions on page 5).
CARE & CLEANING Your desk lamp is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the lamp, using a mild non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit, and allowed sufficient time for the unit to cool. All liquid should be properly wiped away and dried prior to restoring power.
Please visit our web site at: www.Verilux.com 340 Mad River Park, Waitsfield, VT 05673 1-888-544-4865 VD09-MAN-Rev3 Printed in China for Verilux, Inc. © Copyright 2008 Verilux, Inc. All rights reserved.
