33 Digital Multimeter Instruction Manual
TABLE OF CONTENTS page A. INTRODUCTION 1. Congratulations . . . . . . . . . . . . . . . . . .3 2. Product Description . . . . . . . . . . . . . .3 3. EC Declaration of Conformity . . . . . . . .4 B. SAFETY CONSIDERATIONS . . . . . . . . . . . .5 C. TECHNICAL DATA 1. Features and Benefits . . . . . . . . . . . . .6 2. Product Applications . . . . . . . . . . . . . .7 3. Specifications . . . . . . . . . . . . . . . . . . .8 D. MEASUREMENT TECHNIQUES 1. Controls and Functions . . . . . . . . . .10 2.
. EC Declaration of Conformity This is to certify that model 133 conforms to the protection requirements of the council directive 89/336/EEC, in the approximation of laws of the member states relating to Electromagnetic compatibility and 73/23/EEC, The Low Voltage Directive by application of the following standards: EN 50081-1 EN 50082-1 EN61010-1 EN61010-2-031 1992 Emissions Standard 1992 Immunity Standard 1993 Safety Standard 1995 Safety Standard To ensure conformity with these standards, this instrume
INTERNATIONAL SYMBOLS CAUTION: RISK OF ELECTRIC SHOCK AC (ALTERNATING CURRENT) ! 2. Product Applications Perform the following tests and/or measurements with the TPI 133 and the appropriate function: DC (DIRECT CURRENT) HVAC/R REFER TO INSTRUCTION MANUAL FUNCTION DCmV GROUND FUSE DOUBLE INSULATION ON/OFF, PUSH BUTTON SWITCH C. TECHNICAL DATA 1. Features and Benefits Safety Large LCD Rubber Boot Multi-function 6 • Thermocouples in furnaces or gas applications.
3. Specifications IEC 1010 Over Voltage: CAT II - 1000V CAT III - 600V Pollution Degree 2 d. ACA UL 3111-1 a. DCV Range Resolution Accuracy Impedance 200mV 2V 20V 200V 1000V 0.1mV 0.001V 0.01V 0.1V 1V ±0.5% of reading, ±2 digits 10M Range Resolution Accuracy Overload Protection 200µA 2mA 20mA 200mA 2A 10A 0.1µA 0.001mA 0.01mA 0.1mA 0.001A 0.01A ±1% of reading, ±3 digits Fuse* ±1.8% of reading, ±3 digits ± 3% of reading, ± 7 digits F600V, 2A, 31CM Fuse* F600V, 10A, 31CM e.
D. MEASUREMENT TECHNIQUES 2. Step by Step Procedures: 1. Controls and Functions: a. Measuring DC Volts CAUTION! Do not attempt to make a voltage measurement if a test lead is plugged in the A or µmA input jack. Instrument damage and/or personal injury may result. Push Buttons Turns the 133 on and off. Data-H Activates the Data Hold function. Rotary Switch DCV Used for measurement of DC Volts. Select the best range for the voltage to be measured. ACV Used for measurement of AC Volts.
b. Measuring AC Volts CAUTION! Do not attempt to make a voltage measurement if a test lead is plugged in the A or µmA input jack. Instrument damage and/or personal injury may result. b. Measuring AC Volts (cont.) Measurement Procedure: 1. 2. 3. 4. ! WARNING! Do not attempt to make a voltage measurement of more than 1000V or of a voltage level that is unknown. 5. 6. 7. Instrument set-up: FUNCTION BLACK TEST LEAD RED TEST LEAD MINIMUM READING MAXIMUM READING ACV V 0.
c. Measuring DC Amps (cont.) Measurement Procedure: 1. 2. 3. 4. 5. 6. 7. Disconnect power to circuit to be measured. Plug black test lead into the COM input jack. Plug red test lead into mAµA or A input jack depending on value of current to be measured. Set the rotary switch on the 133 to the desired range in the DCA function depending on the current to be measured and the input jack the red test lead is inserted into. Connect test leads in series to circuit to be measured.
e. Measuring Resistance ! WARNING! Do not attempt to make resistance measurements with circuit energized. For best results, remove the resistor completely from the circuit before attempting to measure it. NOTE: To make accurate low ohm measurements, short the ends of test leads together and record resistance reading. Deduct this value from actual readings. Application Notes When measuring resistance of a motor, make sure the power is disconnected prior to testing.
f. g. Continuity Buzzer Measuring Diodes CAUTION! Do not attempt to make diode measurements with circuit energized. The only way to accurately test a diode is to remove it completely from the circuit before attempting to measure it. ! WARNING! Do not attempt to make continuity measurements with circuit energized. Instrument set-up: FUNCTION Instrument set-up: FUNCTION OHM( ) BLACK TEST LEAD RED TEST LEAD MINIMUM READING MAXIMUM READING COM V 0.001V 2.000V Measurement Procedure: 1. 2. 3. 4.
E. ACCESSORIES* F. MAINTENANCE Standard Accessories Part No. 9V Battery Fuse, 2 Amp Fuse, 10 Amp Test Lead Set Rubber Boot (133 only) A009 A102 A110 A040 A101 Optional Accessories Part No. Deluxe Test Lead Set IEC 1010 Deluxe Test Lead Kit Temperature Adapter Boot Hook Soft Carrying Case SDK1C TLS2000BC A301 A103 A100 1. 2. *These accessories have not been evaluated by UL and are not considered as part of the UL Listing of this product. 3.
G. TROUBLE SHOOTING GUIDE WARRANTY Problem Please refer to product warranty card for warranty statement.
3 SPECIFICATIONS ±0.5% Basic DCV Accuracy (also see pages 9-11) Function Range Resolution DCV 200mV 2V 20V 200V 1000V 0.1mV 0.001V 0.1V 0.1V 1V ACV 200mV 2V 20V 200V 750V 0.1mV 0.001V 0.01V 0.1V 1V DCA 200µA 2mA 20mA 200mA 2A 10A 0.1µA 0.001mA 0.01mA 0.1mA 0.001A 0.01A ACA 200µA 2mA 20mA 200mA 2A 10A 0.1µA 0.001mA 0.01mA 0.1mA 0.001A 0.01A OHM 200 2k 20k 200k 2M 20M 0.1 0.001k 0.01k 0.1k 0.001M 0.01M Test Voltage Max. Test Current Diode 2.5V Approx. 1mA Continuity Test Voltage 2.
