Install Instructions

ManualsBrandsVeris ManualsHVAC Supplies4" Discharge Air Temperature Sensor with 10' Cable, 10k Ohm NTC Type 2 Thermistor

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classied locations.

•

Read and understand the instructions before installing this product.

• Turn o all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

If this product is used in a manner not specied by the manufacturer, the protection

provided by the product may be impaired. No responsibility is assumed by the

manufacturer for any consequences arising out of the use of this material.

Installation Guide

Temperature

Product Identication

Product Overview

The TJ Series temperature sensor is designed for VAV systems. The cable is plenum rated, and the probe is stainless

steel for durability. The TJ is warranted for a period of ve years.

TJ Series

VAV Discharge Temperature Sensor

Specications

Wiring 22 AWG; 2-wire RTD/Thermistor

Probe Stainless steel

Operating Temperature Probe: -25° to 105 °C (-13 to 221 °F)

Wiring side: Up to 75 °C (167 °F)

WARRANTY

Limited Warranty 5 years

Sensor Type OptionProbe Length

B = 4" (102 mm)

D = 8" (204 mm)

0 = Standard 5 ft.

cable, no QDs

1 = 1/4" Female

Quick Discon-

nects (QD)

2 = 1/4” QDs with

8 ft. lead wires

3 = 10 ft. cable,

no QDs

= Resistive

Cal Certiﬁcate

0 = None

2 = 3-Point NIST calibration

Output

B = 100R platinum, RTD

C = 1k platinum, RTD

D = 10k T2, Thermistor

E = 2.2k, Thermistor

F = 3k, Thermistor

H = 10k T3, Thermistor

I = 1k Balco (Nickel-Iron) RTD

J = 10k Dale, Thermistor

K = 10k w/11k shunt, Thermistor

M = 20k NTC, Thermistor

N = 1800 ohm, Thermistor

T = 100k, Thermistor

W = 10k T2 high accuracy, Thermistor

Y = 10k T3 high accuracy, Thermistor

Notes:

Increased cable length aects the readings of lower resistance RTDs (100R platinum RTD).

Room temperature oset documented on each unit.

Summary of content (2 pages)

PAGE 1
Installation Guide Temperature TJ Series VAV Discharge Temperature Sensor Product Overview TJ The TJ Series temperature sensor is designed for VAV systems. The cable is plenum rated, and the probe is stainless steel for durability. The TJ is warranted for a period of five years. NOTICE • • • • • This product is not intended for life or safety applications. Do not install this product in hazardous or classified locations. Read and understand the instructions before installing this product.
PAGE 2
TJ Series Installation Guide TM Dimensions 1.5" (38 mm) 0.3" (6.3 mm) 2" (51 mm) L 1.1" (28 mm) 1" (26 mm) Optional 1/4” female quick disconnect Installation 1. Remove adhesive covering from foam gasket. 2. Push probe through hole in gasket until gasket adheres to underside of mounting flange. 3. Drill a 3/8” diameter hole in the duct for the sensor probe. 4. Mount flange to duct using screws provided. 5. Wire as shown. Thermistor RTD Z203571-0K Page 2 of 2 ©2019 Veris Industries USA 800.354.