Installation Guide

ManualsBrandsVerizon Connect ManualsElectronicsVerizon Connect Battery Powered Equipment Asset Tracker

Install the Equipment Asset Tracker - Battery

(EAT-B Device) for Spotlight users

This installation guide for Verizon Connect customers. If you are a Verizon Connect installation partner, refer

to Install the Equipment Asset Tracker - Battery (EAT-B Device) using the Reveal Hardware installer app.

This article includes:

• Device information

• Preparing for installation

• Installing the EAT-B device

• Device support

Device Information

The Equipment Asset Tracker - Battery (EAT-B) device is designed by Verizon Connect for

tracking non-powered assets, such as generators, containers, pumps, and so on.

• Compact and discreet

• Easy to conceal

• Long battery life

• Replaceable battery

• Optimized internal antenna design for a strong signal

• IP67 rated protection against water and dust ingress

Summary of content (9 pages)

PAGE 1
Install the Equipment Asset Tracker - Battery (EAT-B Device) for Spotlight users This installation guide for Verizon Connect customers. If you are a Verizon Connect installation partner, refer to Install the Equipment Asset Tracker - Battery (EAT-B Device) using the Reveal Hardware installer app.
PAGE 2
• • • • Mounting holes (one on each corner) (1) Status LEDs for battery, network, and GPS (2) Status button that wakes the device, runs a status test and sends a report.
PAGE 3
1. EAT-B Device 2. 4 x self-drilling screws for metal: standard 5/16” hex head, number 12 size, 1 inch long 3. 4 x bolts: Serrated-flange 5/16” hex head, 10-32 thread, 1 ¼ inch long, .19 inch screw width 4. 4 x locknuts 3/8” head 5. 4 x washers, flat type What You'll Need • The Reveal Spotlight app to confirm your device can be located on your Reveal Live Map. You can download Spotlight from the App Store (for iOS devices) or Google Play (for Android devices).
PAGE 4
You need this number later when confirming that the device has connected to Reveal. You can find the serial number on the label on the side of the device. Step 2: Find a good location to mount the device. The device should be mounted in a location with a clear view of the sky and where it does not interfere with the safe operation of the asset, or where it is exposed to road debris or highpressure water spray that can damage the device.
PAGE 5
ICON NAME STATUS • Bluetooth Fast flash: GPS location failed. At this time, the device does not support a flash when the device is powered on, but i test/status function. It can be disregarded. The device runs a status test for battery, network, and GPS. It can take up to 30 seconds for the LEDs to light up and they stay on for 5 seconds. To recheck the status, press the Status button. Pressing the Status button a second time does not power off the device.
PAGE 6
1. If the asset is connected, the asset shows on the Map. Assets are represented by square icons. You can also search for the asset in Reveal. • • In Reveal, go to Admin > Asset List. In the Search field, type the device serial number and press Enter. If the asset is connected, it shows in the list.
PAGE 7
Step 5: Mount the device Once you have activated and tested the device, you can mount it to the asset. To mount the device: 1. 2. 3. 4. Hold the device in the mounting position. Mark the positions of the four mounting holes. Drill holes in the positions you’ve just marked. Secure the device to the asset using the included screws or bolts. Do not use rivets or countersink screws. Do not over-torque.
PAGE 8
1. Choose SAVE CHANGES. Device support • Replace the battery pack FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 9
• • • • Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or install technician for help.