User guide

RESTORE PHONE
To delete all User Data and restore all settings to their initial defaults:
1. From standby mode, press the OK Key [OK] to unlock the
keypad, then press the OK Key [MENU], the Directional Key
right twice for SETTINGS & TOOLS, then slide out the QWERTY
keyboard and press 6. Phone Settings, 6. Security.
2. Enter the four-digit Lock Code, then press the OK Key
[OK].
3. Press “5. Restore Phone”.
4. After reading the warning message that appears, press the
Directional Key
up or down to select “Ye s”, and then press the
OK Key [OK].
5. After reading the message that appears, press the OK Key
[OK].
6. Enter the four-digit Lock Code, then press the OK Key
[OK]. The
phone will turn off and then back on again automatically.
SYSTEM SELECT
You can set your phone to search or roam on another network when you are not in
your home area. Leave this setting as default unless you want to alter the system
selection as instructed by your service provider.
1. From standby mode, press the OK Key [OK] to unlock the keypad,
then press the OK Key [MENU], the Directional Key right
twice for SETTINGS & TOOLS, then slide out the QWERTY keyboard
and press 6. Phone Settings, 7. System Select.
2. Press the Directional Key
up or down to select one of the
following settings, then press the OK Key [OK].
• Automatic B: Scan radio channels based on the Automatic B setting.
• Automatic A: Scan radio channels based on the Automatic A setting.
• Home Only: Only within your home area or home affiliated area.
NAM SELECTION
Enables Auto NAM (Number Assignment Modules) or manually selects a NAM.
AUTO NAM
Automatically switches phone to proper NAM when you have multiple NAM
registrations.
1. From standby mode, press the OK Key [OK] to unlock the
keypad, then press the OK Key [MENU], the Directional Key
right twice for SETTINGS & TOOLS, then slide out the QWERTY
keyboard and press 6. Phone Settings, 8. NAM Selection.
66 Chapter 4 − Menu Function
SettingsSettings
2. Press the Directional Key up or down to select “1. Auto NAM”,
then press the OK Key
[OK].
3. Select “On/Off”, then press the OK Key
[OK].
CHANGE NAM
1. From standby mode, press the OK Key
[OK] to unlock the
keypad, then press the OK Key
[MENU], the Directional Key
right twice for SETTINGS & TOOLS, then slide out the QWERTY
keyboard and press 6. Phone Settings, 8. NAM Selection.
2. Press the Directional Key
up or down to select “2. Change
NAM”, then press the OK Key
[OK].
3. Select “NAM 1 - VERIZON” or “NAM 2 - VERIZON” , then press the
OK Key
[OK].
CALL SETTINGS
ANSWER OPTIONS
To determine how to handle an answered call:
1. From standby mode, press the OK Key [OK] to unlock the keypad,
then press the OK Key
[MENU], the Directional Key right
twice for SETTINGS & TOOLS, then slide out the QWERTY keyboard
and press 7. Call Settings, 1. Answer Options.
2. Press the Directional Key
up or down to select one of the
following settings, then press the OK Key [MARK].
Slide Open/Any Key/Auto w/ Hands-free.
“Slide Open” is the default setting for this device.
3. Press the Left Soft Key [Done].
• When the phone is closed, the Auto w/ Hands-free Mode will not function,
except when connected to a headset.
• The Auto w/ Hands-free will function after about five seconds.
• Auto w/ Hands-free is available only when connected to a headset or hands-free
device.
• The three functions can be used at the same time.
• To answer all incoming calls, press the SEND Key .
Menu Function − Chapter 4 67
SettingsSettings
080625_TXT8010_ELVIS_M_EN_REV00.indd 66-67080625_TXT8010_ELVIS_M_EN_REV00.indd 66-67 2008.6.25 9:35:11 PM2008.6.25 9:35:11 PM