Direct Vent Gas Fireplace Models: DV360, DV580 INSTALLER / CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR OUR SAFETY Installation and service must be performed by a qualified installer, service agency or the gas supplier.
DV360/580 Series Direct Vent Gas Fireplace Installation & Operating Instructions This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CSAB149.1 Installation codes for Gas Burning Appliances and Equipment. If the unit is being installed in a mobile home, the installation should comply with the current CAN/CSA Z 240.4 code. For U.S.A Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFPA 54.
DV360/580 Series Direct Vent Gas Fireplace Fireplace Dimensions (Installed as Top Vent) Rough Opening Depth V J P I T Q H V Nailing Flange K W K Recessed S - Rough Opening Width Rough Opening Height U G F R B D C Electrical Access Gas Line Access E L M A G N O Fig. 2 Fireplace specifications and framing dimensions. Ref.
DV360/580 Series Direct Vent Gas Fireplace Fireplace Dimensions (Installed as Rear Vent) Rough Opening Depth U I S H U Nailing Flange J V J Recessed R - Rough Opening Width Rough Opening Height T G F Q B Electrical Access P D C Gas Line Access O E K L A G M N Fig. 3 Fireplace specifications and framing dimensions. Ref.
DV360/580 Series Direct Vent Gas Fireplace Clearance to Combustibles Top of unit to ceiling ................................. 36” (914 mm) Front of unit to combustibles ................... 36” (914 mm) Appliance Top of standoff ....................................... 0” (0 mm) Bottom ..................................................... 0” (0 mm) Side ......................................................... 0” (0 mm) Back ........................................................
DV360/580 Series Direct Vent Gas Fireplace Framing And Finishing C Adjustable Drywall Strip (Nailing Flange) A Check fireplace to make sure it is levelled and properly positioned. B Flange Position A B C To mount the appliance: Choose the location. DV360 (Fig. 5) 1. This unit comes with four (4) flanges pre-mounted on both sides of the fireplace to allow two different drywall thicknesses to be used. Flange “A” is for 1/2” drywall while flange “B“ is for 5/8” drywall. 2.
DV360/580 Series Direct Vent Gas Fireplace High Elevations Input ratings are shown in BTU per hour and are certified without deration for elevations up to 4,500 feet (1,370m) above sea level. For elevations above 4,500 feet (1,370m) in USA, installations must be in accordance with the current ANSI Z223.1/NFPA 54 and/or local codes having jurisdiction. In Canada, please consult provincial and/or local authorities having jurisdiction for installations at elevations above 4,500 feet (1,370m).
DV360/580 Series Direct Vent Gas Fireplace EB-1 Electrical Box Electronic Gas Control Valve The fireplace, when installed, must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code. For USA installations, follow the local codes and the national Electrical Code ANSI/NFPA No. 70. It is strongly suggested that the wiring of the EB-1 Electrical Junction Box be carried out by a licensed electrician.
DV360/580 Series Direct Vent Gas Fireplace Optional Top Vent Application The DV360/580 fireplace is shipped as a rear vent unit. If the layout requires a top vent, convert the unit following the steps below. 1. Remove the 10 screws securing outer collar adapter to fireplace. (Fig. 11) 2. Set outer collar adapter aside. 3. Remove insulation from top of unit and discard. Remove the four (4) screws securing flue cover to top of unit and remove flue cover. (Fig. 12) 4.
DV360/580 Series Direct Vent Gas Fireplace General Venting Your fireplace is approved to be vented either through the side wall, or vertical through the roof. • • • • Only CFM Corporation venting components specifically approved and labelled for this fireplace may be used. Venting terminals shall not be recessed into a wall or siding. Horizontal venting which incorporates the twist lock pipe must be installed on a level plane without an inclining or declining slope.
DV360/580 Series Direct Vent Gas Fireplace General Venting Information - Termination Location INSIDE CORNER DETAIL V D H A V N N E L V B V F C B Fixed Closed B V Ope r Operable able V B CFM145a G V VENT TERMINATION B V Fixed Closed V J G X B I A X AIR SUPPLY INLET M C = Clearance to permanently closed window D = Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2’ (610mm) from the center line of the terminal E = Clearance to
DV360/580 Series Direct Vent Gas Fireplace Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Recessed Location Outside Corner A= Combustible 6"(152mm) Noncombustible 2"(50mm) A V B= Combustible 6"(152mm) Noncombustible 2"(50mm) V C D E C V B Balcony with perpendicular side wall Balcony with no side wall G V V G= Combustible & Noncombustible 12"(305mm) C = Maximum depth of 48" (1219mm) for recessed location.
DV360/580 Series Direct Vent Gas Fireplace Twist Lock Pipes 30 When using twist lock pipe it is not necessary to use sealant on the joints. The only areas of the venting system that need to be sealed with high temperature silicone sealant are the sliding joints of any telescopic vent section used in the system.
DV360/580 Series Direct Vent Gas Fireplace Vent Opening for Combustible Walls 9³⁄₈” (240 mm) 20” (508 mm) Max. Rear Vent Top View 10³⁄₈” (265 mm) DVR584-600 20” DVR584-600 (508 mm) Max. vent no Rear 2/99 djt Framing Detail Fireplace Hearth Fig. 20 Rear vent application, no elbows. 20” (508 mm) Max. Opening for Noncombustible Wall elbows 7¹⁄₂” (190 mm) 45° 45° Fireplace Hearth VO584-100 Fig. 22 Locate vent opening on wall.
DV360/580 Series Direct Vent Gas Fireplace Finished Wall Rise Vent Termination FP1472 Fig. 26 There must be a 1/2” rise per foot length. Vertical Sidewall Application FP1005 Since it is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust, certain limitations FP1472apply and must be strictly as to vent configurations rise in length adhered to.
DV360/580 Series Direct Vent Gas Fireplace Vertical Sidewall Installation Twist Lock Pipe Max. Length 12” (305 mm) Adjustable Zero Clearance Sleeve Step 1 Locate vent opening on the wall. It may be necessary to first position the fireplace and measure to obtain hole location. Depending on whether the wall is combustible or noncombustible, cut opening to size. (Fig. 32) (For combustible walls first frame in opening.
DV360/580 Series Direct Vent Gas Fireplace 7’ (2.1 m) 3 x 90° Elbows 3 x 90° Elbows A FP1176 10’ (3 m) B 8’ (2.4 m) Fig. 27 Maximum three (3) 90° elbows per installation. 36" (914mm) Max. 36" (914mm) Max. V584-201 Fig. 30 Maximum vent run with elbows. In Figures 29 & 30, dimension V584-201 A plus B must not be greater than 17’ (5.2m) Horizontal Run 2/99 djt The maximum number of 45° elbows permitted per side wall installation is two (2).
DV360/580 Series Direct Vent Gas Fireplace X 4” Flex Vent Pipe 12" (305mm) X Spacer Spring 6" (152mm) 5" (127mm) 6³⁄₄" (172mm) FP1182 FP1474 Fig. 36 Install spacer springs. Fig. 35 Horizontal length requirement. Step 4 Step 7 Apply high temperature sealant to 4” (102 mm) and 7” (178 mm) collars or the termination one inch away from crimped end. Guide the vent terminations 4” and 7” collard into their respective vent pipes. Double check that the vent pipes overlap the collars by 2” (51 mm).
DV360/580 Series Direct Vent Gas Fireplace Do not back fill around snorkel. Below Grade Installation When it is not possible to meet the required vent terminal clearances of 12” (305 mm) above grade level, a snorkel kit is recommended. It allows installation depth down to 7” (178 mm) below grade level. The 7” (178 mm) is measured from the center of the horizontal vent pipe as it penetrates through the wall. Ensure the sidewall venting clearances are observed.
DV360/580 Series Direct Vent Gas Fireplace Vertical Through-the-Roof Installation Max. Height 40’ (12.2 m) Min. Height 8’ (2.4 m) Max. 10’ (3 m) Support Straps Every 3’ (.9 m) Max. Height 40’ (12.2 m) Min. Height 8’ (2.4 m) Max. 10’ (3 m) FP1183 Fig. 40 Support straps for horizontal runs. Attic Insulation Shield 1 + 2 + 3 + 4 = 270° 1 2 3 4 1. Locate your fireplace. 2. Plumb to center of the (4”) flue collar from ceiling above and mark position. 3.
DV360/580 Series Direct Vent Gas Fireplace Typical Roof Support Application Typical Ceiling Support Application 3 #5 Sheet Metal Screws per Joint Sealant FP1184 Storm Collar Fig. 43 Venting supports. FP1184 Typical roof/ceiling support apps. Min. 2' (610 mm) TWL101a Fig. 45 Roof flashing. TWL101a Twist Lock Pipe 2/8/99 djt FP1185 Fig. 44 Minimum termination to roof clearance.
DV360/580 Series Direct Vent Gas Fireplace Venting Components 7TDVRVT - Through the wall Rear Vent Termination 584A venting components rear vent term 4/6/99 djt 584B Vent components Starter Kit 2/25/99 djt 584C Vent components 584D 45 degree elbow Vent Components 2/25/99 90 degree djt elbow 10/20/99djttwistlock 584E 2/25/99 Venting Components 10/20/99 twist lock Telescope vent 584F 2/25/99Components djt Venting 10/20/99 twist lock Pipe sections 2/25/99 djt 10/20/99 twist lock 584G Venting Components F
DV360/580 Series Direct Vent Gas Fireplace Operating Instructions Window Frame Assembly Glass Information Only glass approved by CFM Corporation should be used on this fireplace. • • • Fireplace Front • The use of any non-approved replacement glass will void all product warranties. Care must be taken to avoid breakage of the glass. Do not operate appliance with glass front removed, cracked or broken.
DV360/580 Series Direct Vent Gas Fireplace Screw Screw Burner Log Identification Chart Logs Log Front Left Log Front Right Log Rear Log Top Left Log Top Right Log Front Center Log Top Center Log Overlay Grate Hearth Panels Front of Unit H100a Fig. 48 Hearth panel location. H100a hearthofPanels Installation Logs 1/27/00 djt Remove front glass. (Refer to “Window Frame Assembly Removal” Section, Fig. 47) Remove logs from packaging.
DV360/580 Series Direct Vent Gas Fireplace 2. Place the log overlay. Hold the overlay with the flat side down and large cut out for the middle flame on the right. Set the overlay on top of the burner toward the left front inside the stop bracket on the left end and the bend on the front left of the burner. (Fig. 49) A slight adjustment may be needed after placing the front right log. (Fig.
DV360/580 Series Direct Vent Gas Fireplace 6. Place the log top center. Hold the log with the pointed end toward Log Rear the back. Match the two holes on the bottom of the log with the two pins on the top of the log front right. (Refer to Figure 53 for pin locations) Set the log and lay it into the rear log. (Fig. 54) 7. Place the log top right. Hold the log with pointed end to the left.
DV360/580 Series Direct Vent Gas Fireplace Flame Characteristics Burner Lava Rock Placement Place burner lava rock on the burner in front of the front logs. Do not place burner lava rock in the inside corners of the front logs. Large Lava Rock The large lava rock provided with this fireplace must be placed on the firebox base around the sides of the burner assembly and on the tray beneath the grate. It is important to periodically perform a visual check of the pilot and the burner flames.
DV360/580 Series Direct Vent Gas Fireplace Yellow Flame Yellow Flame LG444 DV360 Red Glow ����� ��������� ���������� ��������� LG396 DV580 Red Glow Fig. 59 Correct burner flame apperance for DV360 and DV580.
DV360/580 Series Direct Vent Gas Fireplace Instructions for RF Comfort Control Valve The Comfort Control Valve allows remote control of temperature, fan and flame appearance. NOTE: The antenna should hang in free air away from grounded metal. Operation 1. If the manual switch is in remote position, switch it to LOCAL. (Fig. 60) 2. Turn the pilotstat knob counterclockwise from OFF to the PILOT position, push the knob down, and hold in position. The pilot valve opens and allows gas to flow to the pilot burner.
DV360/580 Series Direct Vent Gas Fireplace Delay Timer Mode Fan Pilot Assembly The shut off delay timer has a maximum of 2 hours and a minimum of zero minutes. To change the timer level, press the time key followed by an arrow key. Pushing the key once will change the timer by 10 minutes. Auto Mode Fan Override During Auto Mode If a lower or higher fan speed is desired when operating in the AUTO mode, the fan speed can be overridden by pushing the fan button followed by the up or down key.
DV360/580 Series Direct Vent Gas Fireplace LED Count 8 7 Service Action Replace valve Confirm stepper motor connection exists 5 Confirm fan connection exists and works 4 Confirm gas type; jumper in place 3 Replace thermopiles 2 Turn fan ON NOTE: Some keys are not active. Auto Path If the manual switch is set to REMOTE, press the mode button to display AUTO on the transmitter. Does the transmitter display the room and temperature setting? Move switch from LOCAL to REMOTE. Press any key within 30 seconds.
DV360/580 Series Direct Vent Gas Fireplace Comfort Valve System Control Sequence of Operation with Transmitter Set manual switch to local or remote Five minute wait period Light pilot burner Did the LED stop blinking? Yes Review LED failure analysis Release pilotstat knob Yes Turn pilotstat knob from PILOT to ON Move switch from local to remote. Press any key on transmitter.
DV360/580 Series Direct Vent Gas Fireplace 3. Using a 1/2” open end wrench remove the orifices. (Fig. 67) Gasket Burner Housing Mixing Tube Front Burner Orifice (Refer to Table on Page 42) Natural Rear Burner Orifice (Refer to Table on Page 42) CO130 Propane Fig. 67 Burner orifice replacement. 4. Converting LP to NG, remove bracket/gasket assembly by unfastening the screw which secures the bracket to the burner����� tray base. Discard bracket and refasten the screw into the hole. (Fig.
DV360/580 Series Direct Vent Gas Fireplace 2/15/99 djt Pilot Orifice Conversion NOTE: It is not necessary to remove the pilot tube for conversion. 1. Remove pilot hood by lifting up. (Fig. 72) 2. Remove pilot orifice with Allen wrench. (Fig. 73) 3. Install conversion pilot orifice. 4. Re-install pilot hood and be sure to align with index tab. Installation is complete. Motor Top Cap Piezo Ignitor OT PIL Pilot Hood LED Local/ Remote Switch Pilot Bracket Pilotstat Knob Plug Antenna FP1037 Fig.
DV360/580 Series Direct Vent Gas Fireplace 5. 6. 7. 8. unfastening the screw on the tray to the right side of the orifice. Slide the bracket/gasket assembly over the fitting on the manifold toward the back with the gasket to the right. Secure the bracket/gasket assembly using the screw removed earlier. (Fig. 67a) Replace the orifices according to the table on Page 42. Replace the mixing tube on the burner housing by removing the two (2) screws that secure the mixing tube to the burner housing assembly.
DV360/580 Series Direct Vent Gas Fireplace 1.
DV360/580 Series Direct Vent Gas Fireplace DV360/580 (continued) Ref. 1. 1a. 1b. 1c. 1d. 1e. 1f. 1g. 1h. 1i. 1j. 2. 3a. 3b. 4. 5. 6. 7a. 7b. 8. 9a. 9b. 10. 11. 12. 12a. 13. 14. 15. 16. 17. 18. 19a. 19b. 20. 21. 22a. 22b. 22c. 22d. 23. 24a. 24b. 25a. 25b. 26a. 26b. Description Log Set Log Front Left Log Front right Log Rear Log Top Left Log Top Right Log Top Center Left Log Top Center Log Overlay Volcanic Rock Ember (Package) Lava Rock (Burner) Burner Housing Assy - Nat.
DV360/580 Series Direct Vent Gas Fireplace DV360/580 (continued) Ref. 27. 28. 29. 30. 31. 32. 33. 34. 35a. 35b. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57a. 57b. 58. 59a. 59b. 60a. 60b. 61. 62. 63. 64. 65a. 65b. 66. 67. 68. 46 Description Electrode Ignitor w/Cable Nut Electrode Pilot tube 1/8” x 24” long w/fittings (SIT Pilot) Thermocouple - RN/RP Cable Ignitor - RN/RP Thermopile - RN/RP Pilot Top Convertible Hood Pilot 3 way Pilot Orifice #65 (Nat.
DV360/580 Series Direct Vent Gas Fireplace DV360/580 (continued) Ref. 69. 70. 71a. 71b. 72a. 72b. 73. 74. 75. 76. Description Transformer EN/EP Ignitor Module Honeywell EN/EP Valve - SIT 822 - EN Valve - SIT 822 - EP Pilot Assembly SIT Top Conv. - EN Pilot Assembly SIT Top Conv.
DV360/580 Series Direct Vent Gas Fireplace Optional Accessories Fan Kits FK12 Fan Assembly 1. Open louvre assembly bottom. 2. Install FK12 fan in back of unit between hearth supports. (Fig. 79) 3. Secure fan on velcro strips. 4. Power to the fan can be supplied by plugging the supply lead into a conveniently located wall socket or by using a hard-wired EB-1 connector box. 5. Be sure fan motor does not touch hearth supports.
DV360/580 Series Direct Vent Gas Fireplace Remote Controls Optional remote control units are available to control different functions of the appliance. Model RC1 RC2 MRC3 Functions Controlled ON/OFF ON/OFF and Temperature ON/OFF and Temperature control with a digital display and a programmable 24 hour clock Wall mounted thermostat control IMT Rear Ceramic Panel Back of Firebox Burner Rear Log Support Ceramic Refractory Panels H102 Ceramic refractory panels are available to line the firebox area.
DV360/580 Series Direct Vent Gas Fireplace For Use in Mobile Homes: Model DV360RMH This appliance may be installed as an OEM installation in a manufactured home (US only), or a mobile home; it must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard Title 24 CFR Part 3280, or Standard for Installation in Mobile Homes CAN/ CSA Z240 MH. This appliance is only for use with the type(s) of gas indicated on the rating plate.
DV360/580 Series Direct Vent Gas Fireplace a) Using a Torx T20 or slotted screwdriver, remove and save the three pressure regulator mounting screws (A), pressure regulator tower (B) and diaphragm (C). b) Ensure the rubber gasket (D) is properly positioned and install the new Hi/ Lo pressure regulator to the valve using the new screws (E) supplied with the kit. Tighten screws securely. (Ref. torque: 25 in-lb). c) Install the enclosed identification label (F) to the valve body where it can be easily seen. 9b.
LIMITED LIFETIME WARRANTY DV360/580 Series Direct Vent Gas Fireplace PRODUCT COVERED BY THIS WARRANTY All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic brand gas fireplaces equipped with an Insta-Flame Ceramic Burner, or standard steel tube burner.
Efficiency Ratings Model DV360RN DV360RP DV360EN DV360EP DV360RFN DV360RFP DV580RN DV580RP DV580EN DV580EP DV580RFN DV580RFP EnerGuide Ratings Fireplace Efficiency (%) 53 53 53 53 53 53 51.1 51.1 51.1 51.1 51.1 51.1 Steady State (%) Fan-OFF Fan-ON 82 83 83 84 82 83 83 84 82 83 83 84 82 83 83 84 82 83 83 84 82 83 83 84 CFM Corporation 2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www.cfmcorp.com D.O.E.
