Majestic Fireplaces® SR/SC Series ™ 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 12345678901234567890123 1234567890123456789
Majestic Fireplaces® SR/SC Series Safety Information PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING FIREPLACE. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Description Any such action may possibly cause a fire hazard. The SR/SC Series fireplaces are solid fuel, woodburning premium fireplaces.
Majestic Fireplaces® SR/SC Series SR36 Series Woodburning Fireplace 22" (559mm) Rough Opening Depth 48¹⁄₂" (1232mm) ¹⁄₂" (13mm) 22¹⁄₂" (572mm) 11" DIA.
Majestic Fireplaces® SR/SC Series SR42 Series Woodburning Fireplace 50" (1270mm) ¹⁄₂" (13mm) (1 79 ⁵ 1m ⁄₈" m (16 ) m m ) Rough Opening Height ⁵⁄₈" Recessed (16mm) Nailing Flange Rough Opening Width 47" (1194mm) 70 ¹ ⁄₂" ¹⁄₂" 11" DIA.
Majestic Fireplaces® SR/SC Series Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation.
Majestic Fireplaces® SR/SC Series Chimney Requirements - Offset Installations OFFSET CHIMNEY FLUE EXIT RISE CHIMNEY SECTION IWF282 B A D E 6 FT. G 30˚ RETURN ELBOW 30˚ OFFSET ELBOW RISE C H OFFSET 30˚ RETURN ELBOW 30˚ OFFSET ELBOW B 30˚ Elbow Offsets G SKCS8 SUPPORT H HEARTH FLOOR Example 1 Example 2 Example 3 Notes: G + H cannot exceed 20 feet.
Majestic Fireplaces® SR/SC Series Planning Information Preplanning an installation is very important to ensure safety and to save time and money. An installer must predetermine where a fireplace will be set and how the chimney system will be run. Mounting The Fireplace 1. A flat combustible surface. 2. A raised wooden platform. 3. A concrete block or other solid object placed beneath each of the four (4) corners of the fireplace.
Majestic Fireplaces® SR/SC Series Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30 feet above the hearth. Chimney supports are required if the vertical height exceeds 30 feet with SK8 chimneys or 20 feet with 3-wall chimneys. Locate chimney supports at ceiling holes or other structural framing at 30 foot (SK8) or 20 foot (3-wall) heights. Spacing between chimney supports must not exceed 30 feet(SK8) or 20 foot (3-wall).
Majestic Fireplaces® SR/SC Series ■ 2. Framing Option For Circulating Models Only — Framing can be constructed before or after the fireplace is set in place, however, most installers build the frame before setting the fireplace. Frame fireplace with 2 X 4 lumber or heavier materials. Refer to framing dimensions in Figures 1, 2, 3 or 4 for basic fireplace specifications. Note: Framing should be positioned to accommodate wall covering and fireplace facing material. ■ 3.
Majestic Fireplaces® SR/SC Series Straight-Up Chimney Installation To mark the centerline of the flue, put the fireplace in final position and measure out from the wall: 9¹⁄₄ inches. Mark a spot on the ceiling directly above the fireplace. Draw a line parallel to the back wall through this mark. (Fig. 11) Using a plumb bob positioned directly over center point of fireplace flue collar, mark the ceiling to establish the chimney center point. (Fig.
Majestic Fireplaces® SR/SC Series The following table gives firestop spacer model numbers: Note: Safety strips are not required over non-combustible floors where all supports at the base of the fireplace are non-combustible. CHIMNEY HOLE SIZE Size of Chimney 8" Flue "SK" Series 8" Flue "S" Series 3-Wall Angle of Chimney at Ceiling 30˚ Vertical SKFS6A SKFS2A 14¹⁄₂" x 25¹⁄₂" 14¹⁄₂" x 14¹⁄₂" FS6A 17⁷⁄₈" x 29⁵⁄₈" FS2A 17¹⁄₂" x 17¹⁄₂" Fig.
Majestic Fireplaces® SR/SC Series Continue installing the pipe as required until pipe is installed up through the ceiling. At this point, you must install a firestop spacer. PIPE SECTION UP PIPE RIM Installing the Firestop Spacer in the Ceiling Hole HEM LANCE PIPE RIM A firestop spacer is used to keep pipe spaced properly and required for safety. Nail the firestop spacer (at each corner) to the framing members of the ceiling hole. Note: A firestop spacer is not required at the roof.
Majestic Fireplaces® SR/SC Series Install the attic insulation shield with the flanges on its base extending down into the framing hole. Nail each corner of attic insulation shield to the framing members of the ceiling hole using 8d nails. Attic shields are not required at the roof.
Majestic Fireplaces® SR/SC Series ■ 7. Installing Top Housing Or Termination Air Space Clearances Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas). Follow the installation instructions provided with the Vermont Castings, Majestic Products chimney termination you have selected. Installing Chimney In a Chase Refer to Figure 5, Page 5 for an illustration of a typical chase installation. CAUTION: Treatment of firestop spacers and construction of chase may vary with type of building.
;; ; ;; Majestic Fireplaces® SR/SC Series Side Wall Protection Adjacent combustible side walls that are within the minimum dimensions shown in Figure 23 of fireplace opening must be protected with Vermont Castings, Majestic Products Wall Shield Model SP40 or a specifically built wall shield described below. The special wall shield design described in Figure 20 is an alternate method of adding protection to side walls and can be used in place of the SP40 with the same wall clearances specified for the SP40.
Majestic Fireplaces® SR/SC Series WARNING: HEARTH EXTENSION MUST BE INSTALLED IN ACCORDANCE WITH FIGURE 23 AND MUST NOT COVER THE BOTTOM FRONT OPENING OF THE CIRCULATING MODEL. ■ 9. Hearth Installation A hearth extension is required to protect a combustible floor in front of the fireplace. Refer to Figure 23 for minimum dimensions and mounting detail.
;; ;; Majestic Fireplaces® SR/SC Series COMMON MATERIALS AND FACTORS MATERIAL K* R MINIMUM THICKNESS NONCOMBUSTIBLE DECORATIVE FACING EH2416 (Majestic Products Company) 0.458 1.09 Common Brick 5.0 0.10 0.50 in.** 5.46 in.** FP533ADD Fig. 24 Hearth extension material factors. Example of Determining Hearth Extension Equivalents To determine the thickness required for any new material: K of new material (per inch) = x K of listed material (per inch) 2x4" HEADER Do not notch at standoffs.
Majestic Fireplaces® SR/SC Series ■ 10. Installing Line For Gas Logs Vermont Castings, Majestic Products fireplaces are designed to accept a 1/2 inch gas line for installation of an approved gas appliance. (Vermont Castings, Majestic Products manufactures a wide variety of gas logs for use in Vermont Castings, Majestic Products fireplaces.) Be sure to have the appliance installed in accordance with building codes. Gas connection may enter from either left or right side of the fireplace.
Majestic Fireplaces® SR/SC Series 1 10 2 12 b 4 c 6 d 3 a 5 8 13 9 14 7 15 11 948 Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. SR/SC36/42 Series Item/Model Number 1. 2. 3. 4. 5. 6a. 6b. 6c. 6d. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Majestic Fireplaces® SR/SC Series Accessories The following accessories for this appliance are available from your local Vermont Castings, Majestic Products distributor. Should you need additional information beyond what your distributor can furnish, contact: Vermont Castings, Majestic Products, 410 Admiral Blvd., Mississauga, Ontario, Canada L5T 2N6, Attn: Technical Services.
Majestic Fireplaces® SR/SC Series Chimney Components U.S. Component Description Model Number Round Top Termination Top used to terminate chimney at roof. (Flashing not included.) RLTSK8 Round Top Termination Extended Top used to terminate chimney at chase. (Flashing not included.) RLTSK8L Flashing Metal finishing required around Contemporary Termination to prevent rain leakage.
Majestic Fireplaces® SR/SC Series (Chimney Components con't.) Canada Component Description Model Number Chimney Collar Enclosure Installs on the "over the chimney collar" of the fireplace; provides outside air to assist in cooling the chimney system. CCE-SK Attic Insulation Shield Used to prevent insulation from coming in contact with the chimney system. AIS-SK SK8 Chimney Sections Used to build chimney systems exposed above roof. 45˚ Chimney Elbows Provides 45˚ offset and return.
Majestic Fireplaces® SR/SC Series ™ LIMITED WARRANTY & 30 YEAR PROTECTION PLAN For MAJESTIC FIREPLACES® PRE-ENGINEERED Fireplace Systems Vermont Castings, Majestic Products warrants its MAJESTIC FIREPLACES® Pre-Engineered Fireplace (“Fireplace”) and Vermont Castings, Majestic Products supplied firegrate, glass doors, outside air system, fan motor, and liners to be free from defects in material or workmanship, as follows: A.
Majestic Fireplaces® SR/SC Series Vermont Castings, Majestic Products 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777 www.majesticproducts.com • www.vermontcastings.