Installation Instruction

ManualsBrandsVerona ManualsCooking Appliances24 Inch Pro-Style Gas Range with 2.5 cu. ft. Convection Oven, 4 Sealed Burners, Infrared Broiler, EZ Clean Porcelain Interior, 2 Heavy Duty Racks, Bell Timer and Full Width Storage Drawer: Matte Black, Natural Gas

IMPORTANT - PLEASE READ AND FOLLOW

✓ Before beginning, please read these instructions completely and carefully.

✓ Do not remove permanently affixed labels, warnings, or plates from the product. This

may void the warranty.

✓ Please observe all local and national codes and ordinances.

✓ Please ensure that this product is properly grounded.

✓ The installer should leave these instructions with the consumer who should retain

for local inspector's use and for future reference.

✓ The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel

Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance

with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN

CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National

Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.

Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical

Codes Part 1 and/or local codes.

INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform

with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

[formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD

(Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home

Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.

INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with

state or other codes or, in the absence of such codes, with the Standard for Recreational

Park Trailers, ANSI A119.5.

Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual

shut-off valve must be installed in an accessible location in the gas line external to the appli-

ance for the purpose of turning on or shutting off gas to the appliance (In Massachusetts

such shutoff devices should be approved by the Board of State Examiners of Plumbers &

Gas Fitters).

If an external electrical source is utilized, the appliance, when installed, must be electri-

cally grounded in accordance with local codes or, in the absence of local codes, with the

national Electrical Code, ANSI/NFPA 70.

This range is supplied with a protective film on steel and aluminium parts.

This film must be removed before installing/using the appliance.

FOR INSTALLER ONLY

THIS RANGE IS FOR RESIDENTIAL USE ONLY

• INSTALLATION INSTRUCTIONS

IMPORTANT - PLEASE READ AND FOLLOW

for residential use only

Model: VEFSGG 244 ..

SINGLE OVEN GAS RANGE

Summary of content (20 pages)

PAGE 1
SINGLE OVEN GAS RANGE for residential use only Model: VEFSGG 244 .. • INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW IMPORTANT - PLEASE READ AND FOLLOW ✓ Before beginning, please read these instructions completely and carefully. ✓ Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. ✓ Please observe all local and national codes and ordinances. ✓ Please ensure that this product is properly grounded.
PAGE 2
WARNING • ALL RANGES CAN TIP • INJURY TO PERSON COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. ✓ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ✓ WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance.
PAGE 3
DATA PLATE CONVERSION LABEL This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement. The appliance guarantee will be void if the appliance is used within a none domestic environnement i.e. a semi commercial, commercial or communal environment.
PAGE 4
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
PAGE 5
GENERAL INFORMATION 1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Latest Edition. 2.
PAGE 6
installation MIN 35" 7/16 (900 mm) (113 mm) PROXIMITY TO SIDE CABINETS 1. This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets. Range dimensions: • width: 23” 7/8 (606.5 mm) • depth: 24” 5/64 (611.
PAGE 7
 PROXIMITY TO SIDE CABINETS min. (300 mm) 3" min. (7 18" min. (457 mm) 11" 13/16 6 mm) mm) 30" min. (762 mm) 13" max. (330 mm) 18" min. (457 mm) 30" min. (762 mm) 13" max. (330 20" min m) . (500 m . (500 m 0" m) (0 m 0" Fig. 1.3a (0 m) 36" (914 mm) 36" (914 mm) 20" min 0" (0 mm ) 0" (0 mm mm) Fig. 1.3b ) A A NT N VE OVE B Fig. 1.4 ASSEMBLING THE BACKGUARD It is mandatory to install the backguard Assemble the backguard as shown in figure 1.
PAGE 8
 LEVELLING THE RANGE The range is equipped with 4 levelling feet and may be levelled by screwing or unscrewing the feet with a spanner (fig. 1.8). It is important to observe the directions of figures 1.6, 1.7a, 1.7b. Fig. 1.6 Supplied with the range in a separate kit 0 mm 0" + 8 mm + 5/16" + 8 mm + 5/16" Fig. 1.7a YOU MUST USE STABILITY ANTI TIP BRACKET TO PREVENT UNIT FROM TIPPING. + 20 mm + 25/32" Fig. 1.7b Fig. 1.8 ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS 1.
PAGE 9
gas connection  All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to te action of LP/Propane gas. The range is equipped for the use with NATURAL gas. It is design-certified by CSA International for NATURAL and L.P. gases with appropriate conversion.
PAGE 10
 PRESSURE REGULATOR INSTALLATION STEP 1 Mount the 1/2” NPT (conical) male connector to the pressure regulator and tighten by using a wrench. Do not over tighten the connector. Over tightening may crack regulator. LOCK Arrow Fig. 2.2 STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The regulator cover must be oriented toward the front side of the range. IMPORTANT: use two spanners to tighten the connection. Regulator cover 10 Fig.
PAGE 11
 GAS CONNECTION SPECIFICATION Range manifold Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) male Gasket 1/2” G cylindrical (ISO 228-1) female To range Extension Extension pipe female pipe pipe fitting fitting Extension pipe Extension pipe male pipe fitting Gasket 1/2” NPT (conical) male 1/2” G cylindrical (ISO 228-1) male Manifold test point pressure 1/8” NPT 1/2” G cylindrical (ISO 228-1) female Connector 1/2” NPT female To mains connection Pressure regulator 1/2” NPT female Arrow
PAGE 12
 b) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company. Please provide the service person with this manual before work is started on the range. (Gas conversions are the responsibility of the dealer or end user.) To range c) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with NATURAL gas.
PAGE 13
 CONVERSION tO LP/PROPANE GAS Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. SETTING THE PRESSURE REGULATOR (fig. 2.6b) The pressure regulator is accessible by removing the bottom drawer; the pressure regulator is positioned on the rear left side of the range.
PAGE 14
 INJECTORS TABLE NOMINAL POWER REDUCED POWER LP/PROPANE 11" W.C.P. NATURAL GAS 4" W.C.P. BTU/hr BTU/hr Ø injector [1/100 mm] Ø injector [1/100 mm] Auxiliary (AUX) 3500 1000 55 90 Semirapid (SR) 6000 1500 72 118 Triple ring (TC) 12000 5000 102 170 Oven burner 13000 1500 109 180 Broil burner 8500 - 88 146 J BURNERS Fig. 2.
PAGE 15
 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTORS OF THE OVEN AND BROIL BURNERS a) Oven Burner – Lift and remove the lower panel inside the oven. – Remove the burner securing screw (fig. 2.10). – Withdraw the burner as shown in figure 2.11 and rest it inside the oven. Take care not to damage the wire to the ignition electrode and the safety valve probe. – Using a 7 mm box spanner, unscrew the injector (indicated by the arrow in fig. 2.
PAGE 16
 G ADJUSTMENT OF THE OVEN BURNER MINIMUM This needs to be done only for the oven burner (the broil is a fixed capacity) by acting on the thermostat in the following way: – Turn on the burner by setting the thermostat knob on position . – Remove the knob and unscrew the by-pass screw "G" (fig. 2.14) about three times by passing a small flat screwdriver (Ø 3 mm blade, 100 mm length) through the panel opening.
PAGE 17
electrical connection If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Check with a qualified electrician if you are not sure whether the range is properly grounded. Do Not ground to a gas pipe.  WARNING A 120-volt, 60-Hz, AC-only, 15-ampere, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
PAGE 18
 WIRING DIAGRAM Fig. 3.
PAGE 19
PAGE 20
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances. Cod.