Installation Instructions

ManualsBrandsVerona ManualsCooking Appliances30 Inch Freestanding Gas Range with 3.6 Cu. Ft. Convection Oven, 4 Sealed Burners, 17,000 BTU Burners, 60 Minute Bell Timer, Flame Failure Safety, 2 Heavy Duty Racks and Storage Drawer: Matte White

THIS RANGE IS FOR RESIDENTIAL USE ONLY

FOR INSTALLER ONLY

GAS RANGE

for residential use only

Models: VEFSGG 304 ..

INSTALLATION INSTRUCTIONS

IMPORTANT - PLEASE READ AND FOLLOW

• Beforebeginning,pleasereadtheseinstructionscompletelyandcarefully.

• Donotremovepermanentlyafxedlabels,warnings,orplatesfromtheproduct.Thismay

voidthewarranty.

• Pleaseobservealllocalandnationalcodesandordinances.

• Pleaseensurethatthisproductisproperlygrounded.

• Theelectricalplugshouldalwaysbeaccessible.

• The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

Installationmustconformwithlocalcodesorintheabsenceofcodes,theNationalFuelGas

CodeANSIZ223.1/NFPA54-Iatestedition.Electricalinstallationmustbeinaccordancewith

theNationalElectricalCode,ANSI/NFPA70-latesteditionand/orlocalcodes.

INCANADA:InstallationmustbeinaccordancewiththecurrentCAN/CGA-B149.1National

GasInstallationCodeorCAN/CGA-B149.2,PropaneInstallationCodeand/orlocalcodes.

ElectricalinstallationmustbeinaccordancewiththecurrentCSAC22.1CanadianElectrical

CodesPart1and/orlocalcodes.

INSTALLATIONINMANUFACTURED(MOBILE)HOME:Theinstallationmustconformwith

theManufacturedHomeConstructionandSafetyStandard,Title24CFR,Part3280[formerly

theFederalStandardforMobileHomeConstructionandSafety,Title24,HUD(Part280)]

or,whensuchstandardisnotapplicable,theStandardforManufacturedHomeInstallations,

ANSI/NCSBCSA225.1,orwithlocalcodeswhereapplicable.

INSTALLATIONINRECREATIONALPARKTRAILERS:Theinstallationmustconformwith

stateorothercodesor,intheabsenceofsuchcodes,withtheStandardforRecreationalPark

Trailers,ANSIA119.5.

Installationofanygas-redequipmentshouldbemadebyalicensedplumber.Amanualshut-

offvalvemustbeinstalledinanaccessiblelocationinthegaslineexternaltotheappliance

forthepurposeofturningonorshuttingoffgastotheappliance(InMassachusettssuchshu-

toffdevicesshouldbeapprovedbytheBoardofStateExaminersofPlumbers&GasFitters).

Ifanexternalelectricalsourceisutilized,theappliance,wheninstalled,mustbeelectrically

groundedinaccordancewithlocalcodesor,intheabsenceoflocalcodes,withthenational

ElectricalCode,ANSI/NFPA70.

Some models are supplied with a protective lm on steel and aluminium

parts.Thislmmustberemovedbeforeinstalling/usingtheappliance.

Summary of content (24 pages)

PAGE 1
GAS RANGE for residential use only R Models: VEFSGG 304 .. INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW • • • • • • Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. Please ensure that this product is properly grounded. The electrical plug should always be accessible.
PAGE 2
WARNING ! To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip device packed with the appliance. • ALL RANGES CAN TIP • INJURY TO PERSONS COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS WARNING ! If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
PAGE 3
DATA PLATE The product data plate is attached inside the bottom pivoting panel. CONVERSION LABEL The Governor of California is required to publish a list of substances known to the state of California to cause cancer or reproductive harm and requires businesses to warn customers of potential exposures to such substances.
PAGE 4
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
PAGE 5
GENERAL INFORMATION 1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 - Latest Edition, CAN/CGA-B149.1 or CAN/ CGA-B149.2. 2.
PAGE 6
installation 1 3” (76 mm) PROXIMITY TO SIDE CABINETS 1. MIN 35” 21/32 (905.5 mm) MAX 36” 11/32 (923 mm) 24 (61 ” 13/6 4.9 4 mm ) Fig. 1.1 29” 7/8 (759 mm) Range dimensions: • width: 29” 7/8 (759 mm) • depth: 24” 13/64 (614.9 mm) • height (without backguard): MIN 35” 21/32 (905.5 mm) - MAX 36” 11/32 (923 mm) • backguard (height): 3” (76 mm) Gas line opening: Wall - 37/64” (14.5 mm) from the right side to centre of range; from 5” 7/16 (138 mm) to 6” 1/8 (155.
PAGE 7
1 GAS AND ELECTRIC CONNECTION Dotted line showing the position of the range when installed Ref. inch mm A 5” 7/16 - 6” 1/8 (*) 138 - 155.5 (*) B 14” 3/8 365 C 37/64” 14.5 (*) : Depending on feet regulation C C B B A Area for ELECTRICAL connection Area for GAS connection Fig. 1.2 A A ASSEMBLING THE BACKGUARD It is mandatory to install the backguard. Assemble the backguard as shown in figure 1.3: • Screw the 2 screws “A” interposing the spacers. • Screw the central screw “B”. B Fig.
PAGE 8
1 PROXIMITY TO SIDE CABINETS STANDARD INSTALLATION F Fig. 1.4a E D Ref. inch mm A 0” 0 B 36” 914 C 11” 13/16 300 D 30” minimum 762 minimum E 18” minimum 457 minimum F 13” maximum 330 maximum G 20” minimum 500 minimum C G F B A Fig. 1.
PAGE 9
1 PROXIMITY TO SIDE CABINETS ISLAND INSTALLATION F Fig. 1.5a D H E Ref. inch mm A 0” 0 B 36” 914 C 11” 13/16 300 D 30” minimum 762 minimum E 18” minimum 457 minimum F 13” maximum 330 maximum G 20” minimum 500 minimum H 12” minimum 305 minimum C G F Fig. 1.
PAGE 10
1 LEVELLING THE RANGE The range is equipped with 4 LEVELLING FEET and may be levelled by screwing or unscrewing the feet (figs. 1.6 - 1.7). It is important to observe the directions of figures 1.6, 1.8a, 1.8b. Fig. 1.6 Supplied with the range in a separate kit Supplied with the range in a separate kit 0” 0 mm + 5/16” + 8 mm + 5/16” + 8 mm Fig. 1.8a + 11/16” + 17.5 mm Fig. 1.8b Fig. 1.7 YOU MUST USE STABILITY ANTI TIP BRACKET TO PREVENT UNIT FROM TIPPING.
PAGE 11
1 INSTALLING THE COOKTOP FRONT GUARD To increase the clearance between the front edge of the cooktop and the burners it is possible to install the cooktop front guard supplied with the appliance. IMPORTANT: To install/remove the guard it is necessary to remove the cooktop. Attempting to install/remove the guard without disassembling the cooktop will result in permanent damage to the appliance. Install the front guard as shown in figure 1.10: 1. 2. 3. 4. 5. 6. 7. Remove the backguard.
PAGE 12
gas connection 2 All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane gas. The range is equipped for the use with NATURAL gas. It is design-certified by CSA International for NATURAL and L.P. gases with appropriate conversion.
PAGE 13
2 PRESSURE REGULATOR INSTALLATION STEP 1 Mount the 1/2” NPT (conical) male connector to the pressure regulator and tighten by using a wrench. Do not over tighten the connector. Over tightening may crack regulator. LOCK Arrow Fig. 2.2 STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The regulator cover must be oriented toward the front side of the range. IMPORTANT: use two wrenches to tighten the connection.
PAGE 14
2 GAS CONNECTION SPEFICICATION Range manifold Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) male Gasket 1/2” G cylindrical (ISO 228-1) female To range Extension pipe female pipe fitting Extension pipe Extension pipe male pipe fitting Gasket 1/2” NPT (conical) male 1/2” G cylindrical (ISO 228-1) male 1/2” G cylindrical (ISO 228-1) female Connector 1/2” NPT female To mains connection Pressure regulator 1/2” NPT female Arrow Fig. 2.
PAGE 15
2 TEST POINT ADAPTER The Test Point adapter is available from the After-Sales Service. b. Any conversion required must be performed by your dealer or a qualified licensed technician or gas service company. Please provide the service person with this manual before work is started on the range. (Gas conversions are the responsibility of the dealer or end user.) c. This range can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with NATURAL gas. d.
PAGE 16
2 CONVERSION TO LP/PROPANE GAS (OR CONVERSION BACK TO THE ORIGINAL GAS - NATURAL GAS) Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. CAUTION: Save the orifices removed from the appliance for future use.
PAGE 17
2 INJECTORS TABLE NOMINAL POWER REDUCED POWER LP/PROPANE 11” W.C.P. NATURAL GAS 4” W.C.P. BTU/hr BTU/hr Ø injector [1/100 mm] Ø injector [1/100 mm] 8000 1500 85 139 Inner crown 2100 1000 42 (*) 70 (*) Inner & outer crown 17000 6500 115 (**) 200 (**) Oven burner 14000 2400 109 190 Broil burner 11000 - 100 170 BURNERS Semirapid (SR) Dual (D) (*) inner crown (“J2” in figure 2.9) (**) outer crown (“J3” in figure 2.
PAGE 18
2 SETTING THE BURNER MINIMUM OF THE COOKTOP BURNERS When switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out even when passing suddenly from maximum to minimum flame. To regulate the flame (fig. 2.10) follow the instructions below: Semirapid burner • Light the burner. • Set the gas valve to “LO” position (minimum rate). • • Remove the knob. With a thin screwdriver, turn the regulation screw “R1” until adjustment is correct.
PAGE 19
2 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTOR OF THE OVEN BURNER • Lift and remove the lower panel inside the oven. • Gently unlock, from the burner, the safety valve probe “V” and the ignition electrode “E” (as indicated in fig. 2.11). Take care not to damage the probe and the ignition electrode. • Unscrew and remove the burner securing screws “A” (fig. 2.11). • Withdraw the burner as shown in figure 2.12.
PAGE 20
2 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTOR OF THE BROIL BURNER • Gently unlock, from the burner, the safety valve probe “V” and the ignition electrode “E” (as indicated in fig. 2.13). Take care not to damage the probe and the ignition electrode. • Unscrew and remove the burner securing screw “A” (fig. 2.13). • Withdraw the burner as shown in figure 2.14. • Using a 7 mm box spanner, unscrew the injector (indicated by the arrow in fig. 2.
PAGE 21
2 ADJUSTMENT OF THE OVEN BURNER MINIMUM This needs to be done only for the oven burner (the broil is a fixed capacity) by acting on the thermostat in the following way: • Turn on the burner by setting the thermostat knob on position “8” (maximum). • Remove the knob and unscrew the by-pass screw “G” (fig. 2.15) about three times by passing a small flat screwdriver (Ø 3 mm blade, 100 mm length) through the panel opening.
PAGE 22
3 electrical connection If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Check with a qualified electrician if you are not sure whether the range is properly grounded. Do Not ground to a gas pipe. A 120-volt, 60-Hz, AC-only, 15-ampere, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
PAGE 23
3 WIRING DIAGRAM OS Sw L L Sw N N T0 T-Zero TC1 TC2 TC3 TC4 TC5 TC6 T MU M L N TL T AS CF P2 P1 F1 V PA SWITCH SECURITY MICROSWITCH COOLING FAN FAILURE LAMP OVEN LAMP AIR FLOW SWITCH FAN MOTOR THERMAL OVERLOAD IGNITION SWITCHES GROUP (COOKTOP BURNERS) ELECTRIC DIAGRAM KEY F1 MS S1 LF AS V TL PA LF 2 1 MS A OS MU TO CF M T MS S1 A IGNITION COIL OVEN/BROIL IGNITION SWITCH MAGNET UNIT - OVEN/BROIL THERMOCOUPLES OVEN/BROIL IGNITION SYSTEM COOLING FAN MOTOR TERMINAL BLOCK EARTH CONNEC
PAGE 24
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances. Cod.