Installation Instructions

ManualsBrandsVerona ManualsCookingVPFSGG365DBU Verona 36" Prestige Series Gas Double Oven Range with 5 Sealed Gas Burners and Full Function Convection Oven - Burgundy

DOUBLE OVEN GAS RANGE

Models: VPFSGG365D..

INSTALLATION INSTRUCTIONS

IMPORTANT - PLEASE READ AND FOLLOW

• Before beginning, please read these instructions completely and carefully.

• Do not remove permanently affixed labels, warnings, or plates from the product. This may

void the warranty.

• Please observe all local and national codes and ordinances.

• Please ensure that this product is properly grounded.

• The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

• The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel Gas

Code ANSI Z223.1/NFPA 54 - Iatest edition. Electrical installation must be in accordance

with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN

CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National

Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.

Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical

Codes Part 1 and/or local codes.

INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with

the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly

the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)]

or, when such standard is not applicable, the Standard for Manufactured Home Installations,

ANSI/NCSBCS A225.1, or with local codes where applicable.

INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with

state or other codes or, in the absence of such codes, with the Standard for Recreational

Park Trailers, ANSI A119.5.

Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual

shut-off valve must be installed in an accessible location in the gas line external to the

appliance for the purpose of turning on or shutting off gas to the appliance (In Massachusetts

such shutoff devices should be approved by the Board of State Examiners of Plumbers &

Gas Fitters).

If an external electrical source is utilized, the appliance, when installed, must be electrically

grounded in accordance with local codes or, in the absence of local codes, with the national

Electrical Code, ANSI/NFPA 70.

FOR INSTALLER ONLY

THIS RANGE IS FOR RESIDENTIAL USE ONLY

Some models are supplied with a protective lm on steel and aluminium

parts. This lm must be removed before installing/using the appliance.

Summary of content (28 pages)

PAGE 1
DOUBLE OVEN GAS RANGE Models: VPFSGG365D.. INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW • • • • • • Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. Please ensure that this product is properly grounded.
PAGE 2
WARNING Tip-Over Hazard A child or adult can tip the range and be killed. Install anti-tip device to range and/or structure per installation instructions. Engage the range to the anti-tip device Installed to the structure. Re-engage anti-tip device if range is moved. Failure to follow these instructions can result in death or serious burns to children and adults.
PAGE 3
DATA PLATE CONVERSION LABEL WARNING: This product can expose you to chemicals including formaldehyde, which is known to the State of California to cause cancer, and lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www. P65Warnings.ca.gov.
PAGE 4
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Installation must conform with local codes. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agente or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
PAGE 5
GENERAL INFORMATION 1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 - Latest Edition, CAN/CGA-B149.1 or CAN/ CGA-B149.2. 2.
PAGE 6
installation 1 PROXIMITY TO SIDE CABINETS 1. This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets. Range dimensions: • width: 35” 7/8 (911 mm) • depth: 23” 31/32 (609 mm) • height (without backguard): MIN 35” 7/16 (900‑mm) MAX 37” 13/32 (950 mm) • backguard IMPORTANT: the backguard is not packaged with the appliance but it is supplied separately by the distributor.
PAGE 7
1 GAS AND ELECTRIC CONNECTION Rif. inch mm A 7” 15/32 190 B 15” 3/4 400 C 5” 1/8 ÷ 7” 3/32 (*) 130 ÷ 180 (*) D 20” 1/8 511 * : Depending on feet regulation Dotted line showing the position of the range when installed Area for ELECTRICAL connection D Area for GAS connection B C A Fig. 1.
PAGE 8
1 13" max. PROXIMITY TO SIDE CABINETS (330 mm) min. (300 mm) 30" min. (762 mm) 11" 13/16 18" min. (457 mm) RANGE WITH 8" BACKGUARD 20" min . (500 m 36" (914 mm) m) Fig. 1.3a 0" (0 mm ) 0" (0 mm 13" max. (3 ) 30 mm) . 20" min 18" min. (457 mm) 30" min. (762 mm) OVEN 11" 13/16 min. (300 mm) m) (500 m OVE 36" (914 mm) N VE 0" m) (0 m 0" ) (0 mm 8 Fig. 1.
PAGE 9
1 13" max. (3 30 mm) PROXIMITY TO SIDE CABINETS min . (30 5m m) 18" min. (457 mm) 12" 30" min. (762 mm) RANGE WITH 2" or 3" BACKGUARD 11" 13/16 min. (300 mm) m) . (500 m 36" (914 mm) 20" min Fig. 1.3c 0" m) (0 m 0" ) (0 mm (330 mm) VENT mm) 12" min T VEN N OVE 5m . (30 20" min . (500 m m) T VEN 36" (914 mm) N OVE min. (300 m) 30" min. (762 mm) 11" 13/16 18" min. (457 mm) OVEN 13" max. 0" (0 mm ) 0" (0 mm ) Fig. 1.
PAGE 10
1 Fig. 1.4 Fig. 1.5 FITTING THE ADJUSTABLE FEET The adjustable feet must be fitted to the base of the cooker before use. Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. ATTENTION: Most important! Pay special attention not to damage the range during this operation. Fit the 4 legs by screwing them tight into the support base as shown in picture 1.5. 0 mm 0" + 1" 31/32 + 50 mm Fig. 1.
PAGE 11
1 ASSEMBLING THE BACKGUARD 8" BACKGUARD A B It is mandatory to install the backguard • Assemble the backguard as shown in figure 1.8a, 1.8b or 1.8c and fix it by screwing the 5 screws “A” (which are already fixed on the back of the cooktop). • Fit the no.3 spacers "B" on the rear of the backguard using the screws and spacers supplied with the backguard kit. A IMPORTANT: Do not install the range without the "B" spacers fitted on the backguard. B 3" BACKGUARD A Fig. 1.
PAGE 12
1 INSTALLING THE ANTI-TIP BRACKET The anti-tip bracket has two components: • the adjustable bracket • the stability bracket IMPORTANT! You must install both parts of the anti-tip bracket and ensure they are properly fitted together to prevent the range from tipping. To fit the anti-tip bracket 1 2 3 Fig. 1.9 1. Thread the bolt through the adjustable bracket and fix in place using the two supplied nuts. Exnsure the nuts are well tightened. Fig. 1.10 2.
PAGE 13
1 3. • • • 4. • Fix the stability bracket in place. It can be fixed as follows: To the floor OR on the rear wall by #4 screws (supplied). To the floor AND on the rear wall by #8 screws (supplied). • There are 8 x wood screws and 8 x screws with plastic sleeve anchors supplied with the range in two separate kits. Use the proper screws according to the type of material on the floor and/ or wall.
PAGE 14
1 INSTALLING THE COOKTOP FRONT GUARD (Only for the models without hob rail) To increase the clearance between the front edge of the cooktop and the burners it is possible to install the cooktop front guard supplied with the appliance. IMPORTANT: To install/remove the guard it is necessary to remove the cooktop. Attempting to install/remove the guard without disassembling the cooktop will result in permanent damage to the appliance. Install the front guard as shown in figure 1.12: 1.
PAGE 15
gas connection 2 All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to te action of LP/Propane gas. The range is equipped for the use with NATURAL gas. It is design-certified by CSA International for NATURAL and L.P. gases with appropriate conversion.
PAGE 16
2 PRESSURE REGULATOR INSTALLATION STEP 1 Mount the 1/2” NPT (conical) male connector to the pressure regulator and tighten by using a wrench. Do not over tighten the connector. Over tightening may crack regulator. LOCK Arrow Fig. 2.2a STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The regulator cover must be ordiented toward the front side of the range. IMPORTANT: use two spanners to tighten the connection.
PAGE 17
2 STEP 3 Insert the extension pipe + pressure regulator group in the “A” bracket. A A Fig. 2.2c STEP 4 Assemble the extension pipe + pressure regulator group to the range manifold interposing the gasket supplied. The regulator cover must be ordiented toward the front side of the range. IMPORTANT: use two spanners to tighten the connection. Fig. 2.
PAGE 18
2 STEP 5 Fix the “B” bracket on the back of the range by the 2 (two) screws supplied with the kit for gas connection. The regulator cover must be ordiented toward the front side of the range. B B Fig. 2.
PAGE 19
2 PRESSURE REGULATOR INSTALLATION To range Range manifold Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) male 1/2” G cylindrical (ISO 228-1) female Gasket nExtension oisnetxE elamfemale ef epip pipe gpipe nittiffitting epip To mains connection Extension pipe Extension pipe male pipe fitting Pressure regulator Gasket 1/2” NPT (conical) male 1/2” NPT female 1/2” NPT female 1/2” G cylindrical (ISO 228-1) male Connector Arrow 1/2” G cylindrical (ISO 228-1) female WARNING: check the righ
PAGE 20
2 TEST POINT ADAPTER The Test Point adapter is available from the After-Sales Service. c) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company. Please provide the service person with this manual before work is started on the range. (Gas conversions are the responsibility of the dealer or end user.) d) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with NATURAL gas.
PAGE 21
2 CONVERSION TO LP/PROPANE GAS (OR CONVERSION BACK TO THE ORIGINAL GAS - NATURAL GAS) Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. CAUTION: Save the orifices removed from the appliance for future use. SETTING THE PRESSURE REGULATOR (fig. 2.
PAGE 22
2 INJECTORS TABLE BURNERS NOMINAL POWER REDUCED POWER BTU/hr BTU/hr LP/PROPANE 11" W.C.P. Ø injector NATURAL GAS 4" W.C.P. Ø injector [1/100 mm] [1/100 mm] Semi-rapid (SR) 8000 1500 85 139 Triple ring (TR) 12000 5000 102 170 Inner crown 2800 (1) 1100 (1) 50 (no. 1 central) 80 (no. 1 central) Outer crown 17000 (2) 6500 (2) 80 (no. 2 outer) 139 (no.
PAGE 23
2 SETTING THE BURNER MINIMUM When switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out even when passing suddenly from maximum to minimum flame. To regulate the flame (fig. 2.7) follow the instructions below: Triple-ring and semirapid burner • Light the burner. • Set the gas valve to • • Remove the knob. With a thin screwdriver, turn the regulation screw “R1” until adjustment is correct. position (minimum rate).
PAGE 24
2 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTORS OF THE OVEN AND BROIL BURNERS (LEFT and RIGHT OVEN) a) Oven Burner – Lift and remove the lower panel inside the oven. – Remove the burner securing screw (fig. 2.8). Fig. 2.8 – Withdraw the burner as shown in figure 2.9 and rest it inside the oven. Take care not to damage the wire to the ignition electrode and the safety valve probe. – Using a 7 mm box spanner, unscrew the injector (indicated by the arrow in fig. 2.
PAGE 25
2 ADJUSTMENT OF THE OVEN BURNER MINIMUM (LEFT and RIGHT OVEN) Fig. 2.12 G This needs to be done only for the oven burner (the broil is a fixed capacity) by acting on the thermostat in the following way: – Turn on the burner by setting the thermostat knob on position 8. – Remove the knob and unscrew the by-pass screw "G" (fig. 2.12) about three times by passing a small flat screwdriver (Ø 3 mm blade, 100 mm length) through the panel opening.
PAGE 26
electrical connection 3 WARNING If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Check with a qualified electrician if you are not sure whether the range is properly grounded. Do Not ground to a gas pipe. A 120-volt, 60-Hz, AC-only, 15-ampere, fused electrical supply is required. A timedelay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
PAGE 27
3 WIRING DIAGRAM 27
PAGE 28
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances. Cod.