S7085x 8-Port 10/100 Fast Ethernet Switch Installation Guide Copyright January 2003 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.
The information contained in this document is subject to change without prior notice. Copyright ©. All rights reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. Warning This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
Table of Contents 1. Introduction........................................................................ 4 1.1 1.2 Features........................................................................................5 Specifications...............................................................................6 2. Installing the Switch........................................................... 8 2.1 2.2 2.3 Unpacking....................................................................................
1. Introduction This 8-port Fast Ethernet switch series provides seven 10/100 TP ports and one 100BaseFX fiber port, each capable of transmitting or receiving information simultaneously at full wire speed to control and allocate the network bandwidth. The key features of this switch unit are: . Optimized Bandwidth: Combining eight 10/100Mbps-based Fast Ethernet switched ports, the switch delivers a high network bandwidth for your Fast Ethernet network. .
1.1 Features Designed for resolving congestion problems caused by bandwidth-hungry devices and bandwidth-intensive applications as well as a high number of users, the switches not only adhere to the IEEE 802.3 10BaseT, 802.3u 100BaseTX and 100BaseFX standards, but also feature: . Seven 10/100BaseTX auto-negotiation switched ports and one 100BaseFX port for flexible connections to desktop PCs, servers and Fast Ethernet devices. .
1.2 Specifications 10/100 Ports 100FX Port Flow Control Cables LED indicators Forwarding rate Filtering address MAC address Aging time Environment Dimensions DC IN jack DC IN voltage Consumption IEEE 802.3 10BaseT, 802.3u 100BaseTX std. Shielded RJ-45 jacks with Auto MDI-X detection Auto-negotiation capable Speed for 10Mbps or 100Mbps Full-duplex or half-duplex mode support IEEE802.3u 100BaseFX compliant Fixed 100Mbps operation Duplex mode selector – full duplex or half-duplex IEEE 802.
100FX Port Fiber Specifications Model S70853 S70854 S70855-2 S70855-5 S70855-7 Connector ST SC SC SC SC Fiber Cable MM*2 MM SM*3 SM SM Max. Distance*1 2 Km 2 Km 20 Km 50 Km 70 Km *1: Operating on full duplex mode *2: Multimode fiber – 62.5/125µm, 50/125µm *3: Single Mode fiber – 9/125µm 100FX Port Optical Specifications Model S70853 S70854 S70855-2 S70855-5 S70855-7 Wavelength 1310nm 1310nm 1310nm 1310nm 1310nm Tx Power -19~ -14dBm -19~ -14dBm -15~ - 8dBm -5~ 0dBm 0~ + 5dBm 7 Rx Power -31dBm min.
2. Installing the Switch 2.1 Unpacking Check to see that you have everything before you start the installation. . Installation guide . The switch unit . One AC power adapter for the unit 2.2 Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. The specifications of the AC power adapter are: . AC input power: . DC output power: .
2.3 Installing the Switch 1. Install the switch with the AC power adapter provided. 2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet. 9 www.versitron.
3. Making Network Connections 3.1 Switched Ports The following figure shows the location of the switched ports: 3.
3.3 Making Fiber Connection For different fiber connections, several alternative models can be selected for different fiber connections. Refer to Section 1.2 for model selection.
4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the switch as illustrated below: 4.2 Interpretation LED Functions POWER LED: LNK/SPD/ACT LED: DUP/COL LED: indicates the power status of the switch.
