Specifications
DMU-2000 DATA MANAGEMENT UNITPage 46
MEMORY MODE
It is possible to rotate the antenna automatically to headings, which you store into memory in advance. Use of a Yaesu
Rotator (G-800DXA, G-1000DXA, or G-2800DXA) requires the connection of the optional T9101556 cable to the
connector located on the back of the transceiver.
G
REAT
C
IRCLE
M
AP
/ R
OTATOR
C
ONTROL
FUNCTION
PROGRAMMING BEAM HEADINGS INTO MEMORY
1. Press the
[
KEY4
(
MODE
)]
key, as necessary, to select
the “PRESET” or “MANUAL” mode.
2. Use the techniques learned previously to rotate the
antenna to the desired beam heading.
3. Now press the
[
KEY4
(
MODE
)]
key to select the
“MEMORY” mode.
4. Select the desired memory channel register by using
the
[
KEY2
(
)]
key and
[
KEY3
(
)]
keys, then press
the
[
KEY6
(
MW
)]
key to memorize the programmed
beam heading.
Advice: The maximum number of beam-heading memo-
ries which can be stored is 9.
If you have connected your after-market keyboard to the
DMU-2000, you can append a name (tag) to the memory
channel (maximum: 6 characters). It is often convenient
to enter the callsign of a station, or perhaps a label such as
“Europe” for easy reference. The method of entering the
name tag into a memory is described below.
1. Use the
[
KEY2
(
)]
key and
[
KEY3
(
)]
keys to se-
lect the rotator memory register onto which you wish
to append a name tag.
2. Press the keyboard’s
[
ENTER
]
key; the cursor on the
screen will blink.
3. Use your keyboard to enter the name tag; a maximum
of six characters may be utilized.
MEMORY RECALL
1. Use the
[
KEY2
(
)]
key and
[
KEY3
(
)]
keys to se-
lect the desired location from the rotator memory list.
2. When you briefly press the
[
KEY5
(
MR/ERASE
)]
key,
the rotator will turn to the memorized beam heading.
ERASING MEMORY
1. Use the
[
KEY2
(
)]
key and
[
KEY3
(
)]
keys to se-
lect the rotator memory you wish to erase.
2. Press the
[
KEY5
(
MR/ERASE
)]
key for 2 seconds to
erase the memory’s data.
Note: Once erased, memory data cannot be restored!
“REGULAR COMPASS” DISPLAY
“GREAT CIRCLE MAP” DISPLAY
MANUAL
REFERENCE
[
KEY1
(
xxx
)]
[
KEY2
(
xxx
)]
[
KEY3
(
xxx
)]
[
KEY4
(
xxx
)]
[
KEY5
(
xxx
)]
[
KEY6
(
xxx
)]
[
KEY7
(
xxx
)]
[
KEY8
(
xxx
)]
FT-950
FTDX5000
[
1.8
(
1
)]
[
3.5
(
2
)]
[
7
(
3
)]
[
10
(
4
)]
[
14
(
5
)]
[
18
(
6
)]
[
21
(
7
)]
[
24.5
(
8
)]
FT-2000
FT-2000D
[
F1
(
CH-1
)]
[
F2
(
CH-2
)]
[
F3
(
CH-3
)]
[
F4
(
CH-4
)]
[
F5
(
MEM
)]
[
F6
(
DEC
)]
[
F7
(
P.BACK
)]
[
DISPLAY
]