HX270E VHF/FM Marine Handheld Transceiver Owner's Manual HX 2 70 E
TABLE OF CONTENTS 1. GENERAL INFORMATION ........ 2 2. ACCESSORIES .......................... 3 2.1 PACKING LIST ................................... 3 2.2 OPTIONS ............................................ 3 3. BATTERY ................................... 4 3.1 BATTERY CHARGING ....................... 4 3.2 BATTERY REMOVAL/ INSTALLATION ..... 4 3.3 USING THE NC-88 BATTERY CHARGER .... 5 3.4 FBA-25A ALKALINE BATTERY CASE .... 5 3.5 BATTERY SAFETY ............................ 6 4. CONTROLS AND INDICATORS ...
Congratulations on your purchase of the HX270E! Whether this is your first portable marine VHF transceiver, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON organization is committed to ensuring your enjoyment of this high-performance transceiver, which should provide you with many years of satisfying communications even in the harshest of environments.
1. GENERAL INFORMATION 1.1 INTRODUCTION The HX270E is a submersible, miniature 5-Watt portable two-way VHF marine transceiver. The transceiver has all allocated USA, international, or Canadian channels. It has an emergency channel 16 which can be immediately selected from any channel by pressing the 16/9 key.
2. ACCESSORIES 2.1 PACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: • HX270E Transceiver • FNB-83 7.2 V, 1400 mAh Ni-MH Battery Pack • NC-88C/U 230 VAC Overnight Charger • CD-26 Charger Cradle • FBA-25A Alkaline Battery Case • CAT460 Antenna • E-DC-19A DC Cable with 12 V Cigarette Lighter Plug • CLIP-14 Belt Clip with screw • Owner’s Manual 2.
3. BATTERY The FNB-83 is a high performance rechargeable battery providing high capacity in a compact package. 3.1 BATTERY CHARGING If the radio has never been used, or its charge is depleted, it may be charged by connecting the NC-88 battery charger (see figure 2 on page 5). If 12V DC power is available, the optional E-DC-6 or the E-DC-19A DC adapter with cigarette plug may be used for charging the battery.
3.3 USING THE NC-88 BATTERY CHARGER 1. Install the supplied FNB-83 battery pack on the rear of the HX270E. Ensure that the transceiver is switched off. 2. Plug the NC-88 Overnight Charger into the AC line outlet, then insert the cable plug into the jack located on the side panel of the CD-26 Charger Cradle. 3. Insert the transceiver and battery pack into the CD-26; the antenna jack should be at the left side when viewing the charger from the front. 4.
3.5 BATTERY SAFETY Battery packs for your transceiver contain Ni-MH batteries. This type of battery stores a charge powerful enough to be dangerous if misused or abused, especially when removed from the transceiver. Please observe the following precautions: DO NOT SHORT BATTERY PACK TERMINALS Shorting the terminals that power to the transceiver can cause sparks, severe overheating, burns, and battery cell damage. If the short is of sufficient duration, it is possible to melt battery components.
4. CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. For detailed operating instructions, refer to section 5 of this manual. Refer to Figure 3 for the location of the following controls, indicators, and connections.
4.1 CONTROLS AND CONNECTIONS Antenna Connector The supplied CAT460 flexible antenna is attached here. POWER SWITCH/VOLUME CONTROL Turns the transceiver on and off, and adjusts the volume. PUSH-TO-TALK (PTT) SWITCH Activates transmission. SQUELCH (SQL) SWITCH Sets the point at which random noise on the channel does not activate the audio circuits but a received signal does. This point is called the Squelch threshold.
DW KEY Press the DW key, scan for voice communications on the priority channel and another selected channel until a signal is received on either channel (Dual Watch). Refer to section “5.8 DUAL WATCH” for details. H/L KEY Toggles the transmitter power level between High (5 Watts), Medium (2.5 Watts), and Low (1 Watt) of output. Does not operate on “low power only” and transmission-inhibit channels.
4.2 INDICATORS Figure 4 Indicators Channel Display The operating channel is shown on the LCD in both the transmission and reception modes. A Indicator Signifies ship-to-ship channels in USA or Canadian mode (whose counterpart in the International mode is a public correspondence (marine operator) channel). USA/INTL/CAN Indicator Denotes the “band” of operation for the particular channel. “USA” indicates the USA band; “CAN” indicates the Canadian band; and “INTL” indicates the International band.
MEM Indicator The channel is in the transceiver’s “Scan Memory.” Battery Indicator When the battery charge is almost depleted, a “ ” icon will appear on the display. When this icon appears, it is recommended that you charge the battery soon. No Icon (Blinking) Enough battery power Lower battery power Nearing depletion Prepare to charge the battery NOTE: The battery indicator should be used only as a guide in charging the FNB-83 battery.
5. OPERATION 5.1 INITIAL SETUP 1. Install the belt clip on the transceiver, if desired. 2. Install the battery pack on the transceiver (see figure 1 and section 3.2). 3. Install the antenna onto the transceiver. NOTE ¯ Water resistance of the transceiver is assured only when the battery pack and antenna are attached to the transceiver. Figure 5 Antenna Installation Installing the Quick Draw Belt Clip 1.
5.2 RECEPTION 1. Turn the POWER/VOLUME CONTROL knob clockwise to turn the transceiver on. 2. Press the SQL key, then press the [T] key until the SQL level is 00. 3. Turn up the POWER/VOLUME CONTROL knob until the noise or audio from the speaker is at a comfortable level. 4. Select a channel that has no signal being received (no one is transmitting on the channel) and where only noise is heard. 5. Press the SQL key, then press the [S ] key and stop immediately after the noise disappears.
5.3 TRANSMISSION NOTE Never key the transceiver without an antenna connected, as this may cause damage to the transceiver. 1. Perform steps 1 through 7 of the RECEPTION discussion above. 2. Before transmitting, monitor the channel and make sure it is clear. 3. For communications over short distances, press the H/L key until “ ” is displayed on the LCD. This indicates Low power (approximately 1 Watt). NOTE Transmitting on 1 Watt prolongs battery life. Low power (1 Watt) should be selected whenever possible.
5.5 USA, CANADIAN, AND INTERNATIONAL BANDS 1. To change the operating band (channel set) of the transceiver, hold down the 16/9 key and press the DW key. The band will change from USA, to International, and to Canadian with each press. 2. “USA” appears on the LCD for the USA band, “INTL” appears for the International band, and “CAN” appears for the Canadian band. 5.
5.7 PROGRAMMABLE PRIORITY SCAN The priority scanning feature allows the radio to scan while also keeping watch on a particularly important “priority channel.” The following channels can be set as the priority channel: 16, 09, and Preset Channels 1 through 8 (Preset Channels are described in section 5.13). 1. To set the priority channel, hold down the 16/9 key and press the MEM key.
5.9 EMERGENCY (CHANNEL 16 USE) Channel 16 is known as the Hail and Distress Channel. An emergency may be defined as a threat to life or property. In such instances, be sure the transceiver is on and set to CHANNEL 16. Then use the following procedure: 1. Press the PTT (push-to-talk) switch and say “Mayday, Mayday, Mayday. This is , , ” (your vessel’s name). 2. Then repeat once: “Mayday, ” (your vessel’s name). 3.
Prior to making contact with another vessel, refer to the channel charts in this manual, and select an appropriate channel for communications after initial contact. For example, Channels 68 and 69 of the U.S. VHF Charts are some of the channels available to non-commercial (recreational) boaters. Monitor your desired channel in advance to make sure you will not be interrupting other traffic, and then go back to either channel 16 or 9 for your initial contact.
5.13 PRESET CHANNELS (1 ~ 8): INSTANT ACCESS Eight user-assigned channels can be programmed for instant access. 5.13.1 Programming 1. Hold down the PRESET key, and press the [S] or [T] key (repeatedly, if necessary) until the desired channel number (from among the regular operating channels) is displayed. 2. With the desired channel number displayed, release the PRESET key.
5.15 SETUP MODE The HX270E’s Setup Mode allows a number of the HX270E operating parameters to be custom-configured for your operating requirements. The Setup Mode is easy to activate and set, using the following procedure: 1. Turn the radio off. 2. Hold down the SQL key, then turn on the transceiver while still holding down the SQL key. 3. “SEt” will appear on the display, indicating that the Setup Mode has been activated. 4. Press the SQL key to select the Menu item to be adjusted (see below). 5.
5.15.1 bEP (KEY BEEP) Function: Enable/Disable the Keypad beeper. Available Values: ON/OFF Default: ON 5.15.2 dUL (DW DISPLAY) Function: Selects the Dual Watch scanning display mode. Available Values: nor (Normal)/SPL (Special) Default: SPL (Special) When “Special” is selected, channel number which is the LCD shows received channel. 5.15.3 LP (LAMP MODE) Function: Select the LCD/Keypad Lamp mode.
6. MAINTENANCE The inherent quality of the solid-state components in STANDARD HORIZON radios will provide many years of continuous use. Take the following precautions to prevent damage to the radio. Keep the microphone connected or the jack covered at all times to prevent corrosion of electrical contacts; Never key the transmitter unless an antenna or suitable dummy load is connected to the antenna receptacle. Use only STANDARD HORIZON-approved accessories and replacement parts.
MEMO HX270E Page 23
7. CHANNEL ASSIGNMENTS CH 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 15 16 17 18 19 20 21 22 23 24 25 26 27 28 60 61 62 63 64 65 65 66 67 68 69 VHF MARINE CHANNEL CHART TX RX Remarks 156.050 160.650 Duplex 156.100 160.700 Duplex 156.150 160.750 Duplex 156.200 160.800 Duplex 156.250 160.850 Duplex 156.300 Simplex 156.350 160.950 Duplex 156.400 Simplex 156.450 Simplex 156.500 Simplex 156.550 Simplex 156.600 Simplex 156.650 Simplex 156.700 Simplex --156.750 Receive only 156.750 Simplex 156.800 Simplex 156.
The following channels may be fitted to your radio. These are only licensed for use in the countries indicated. No attempt should be made to use them in any other country. Designation M M2 31 96 L1/1L L2/2L L3/3L F1/1F F2/2F F3/3F Tx 157.850 161.425 157.550 162.425 155.500 155.525 155.650 155.625 155.775 155.825 Rx 157.850 161.425 161.150 162.425 155.500 155.525 155.650 155.625 155.775 155.
8. SPECIFICATIONS 8.1 General Frequency range: Frequency stability: Emission type: Antenna impedance: Supply voltage: Current consumption: Operating Temperature: Waterproof rating: Case Size (W x H x D): Weight (Approx): 156 MHz - 163.275 MHz (Marine Band) Channel Steps: 25 kHz ± 5 ppm (–30 °C to +60 °C) 16K0G3E 50 Ohms 7.2 VDC 200 mA (Receive) 40 mA (Standby, Saver Off) TX: 1.4 A (H)/0.9 A (M)/0.5 A (L) –30 °C to +60 °C 30 minutes @ 1 meter depth (JIS 7) 58 x 120 x 30.5 mm 380 g with FNB-83 8.
MEMO HX270E Page 27
MEMO Page 28 HX270E
VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. YAESU EUROPE B.V. P.O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong E M 0 0 7 N 2 5 1 Copyright 2005 VERTEX STANDARD CO., LTD.
