Specifications

VX-7R OPERATING MANUAL 83
SET MODE
ø1: Depends on the Frequency Band. ø2: Requires optional SU-1 ø3: Depends on the Transceiver Version.
Function
Selects the Tone Encoder and/or Decoder mode.
Setting of the CTCSS Tone Frequency.
Setting of the DCS code.
Enables/Disables “Inverted” DCS code decoding.
Selects the CTCSS Bell ringer repetitions.
Enables/disables split CTCSS/DCS coding.
Enables/disables the DTMF Autodial feature.
Programming of the DTMF Autodialer.
Selects the Channel Counter Search Width.
Enables/disables the Band-edge beeper while scanning.
Selects the Scan Resume mode.
Enables/disables the Scan lamp while paused.
Selects the Smart Search Sweep mode.
Selects the Spectrum Analyzer Sweep mode.
Enables/disables the audio output of the center frequency
(q) when the Spectrum Analyzer is activated in the
Amateur band.
Selects the display of the sensor units’s information.
Select the Wave Form to be monitored.
Selects the measurement units for the Temperature sensor.
Selects the measurement units for the Barometric
Pressure sensor
ø2
.
Correcting the Barometric Pressure
ø2
.
Select the measurement units for the Altimeter
ø2
.
Correcting the Altimeter
ø2
.
Setting of the Automatic Power-Off time.
Selects the Receive-mode Battery Saver interval (“sleep”
ratio).
Enables/disables the Transmit Battery Saver.
Setting of the TOT time.
Set the ON Timer time.
Set the OFF Timer time.
Select the Beep option during ARTS operation.
Select the Polling Interval during ARTS operation.
Program and activate the CW Identifier (used during
ARTS operation).
Enables/disables the Busy Channel Lock-Out feature.
Selects the function of the [HM/RV(EMG)] key.
Selects the MONI key (just below the PTT switch)
function.
Exchange the functions between the [MON/F] key and the
MONI keys on the left side of the radio.
Select the alarms utilized when the Emergency function is
engaged.
Reducing the Deviation level by 50%.
Enables/disables VOX operation; sets VOX sensitivity.
Selects the VOX delay (“hang”) time.
Enables/disables the BAND Link feature.
Selects or disables the VFO Band edge for the current
band.
Editing of the User font.
Enables/disables the Icon display.
Editing of the User Icon.
ICON selection.
Shifting of CPU clock frequency.
Sets the Clock time.
Selects the language for the Set (Menu) mode selections.
Enables/disables the Front-end Attenuator
Enables/disables the Microphone Monitor feature.
Enables/disables the Weather Alert Feature
Available Values
(
Default: Bold Italic
)
OFF/TONE/TONE SQL/DCS
50 standard CTCSS tones
(88.5 Hz)
104 standard DCS codes (023)
ENABLE/DISABLE
OFF/1/3/5/8/CONTINUE
OFF/ON
ON/OFF
–
±5 MHz/±10 MHz/± 50 MHz/
±100 MHz
ON/OFF
3SEC/5SEC/7SEC/10SEC/BUSY/
HOLD
ON/OFF
1/CONTINUOUS
1/CONTINUOUS
ON/OFF
TIME/DC/TEMP/WAVE/BARO
ø2
/
ALTI
ø2
/WX
ø2
/OFF
ALL/ RX SIGNAL / TX MODULATION
°C/°F
ø3
hpa/mbar/mmHg/inch
ø3
–
m/ft
ø3
–
OFF/30 min/1 hour/3 hours/
5 hours/8 hours
OFF/200mS(1:1)/300mS(1:1.5)/
500mS(1:2.5)/1s(1:5)/2s(1:10)
ON/OFF
OFF/1 min/2.5 min/5 min/10 min
OFF/00:00 ~ 23:59
OFF/00:00 ~ 23:59
IN RANGE/ALWAYS/OFF
15 SEC/25 SEC
–
ON/OFF
HOME/REV
MONI/T-CAL
ø3
FUNC/MONI
BEEP+STROBE/BEEP/
STROBE1/STROBE2/STROBE3/
STROBE4/ STROBE5/BEAM
ON/OFF
OFF/HIGH/LOW
0.5S/1S/2S
ON/OFF
ALL/BAND
–
ON/OFF
–
–
ON/OFF
–
ENGLISH/JAPANESE
ON/OFF
ON/OFF
ON/OFF
Set Mode Item
#1 [SQL TYPE]
#2 [TONE SET]
#3 [DCS SET]
#4 [DCS COMPLEMENT]
#5 [BELL]
#6 [SPLIT TONE]
#7 [DTMF DIALER]
#8 [DTMF SET]
#1 [CH COUNTER]
#2 [EDGE BEEP]
#3 [RESUME]
#4 [SCAN LAMP]
#5 [SMART SEARCH]
#6 [SPEC-ANALYZER 1]
#7 [SPEC-ANALYZER 2]
#1 [SENSOR DISPLAY]
#2 [WAVE MONITOR]
#3 [TEMP UNIT]
#4 [BARO UNIT]
#5 [BARO OFFSET]
#6 [ALTITUDE UNIT]
#7 [ALTITUDE OFFSET]
#1 [APO]
#2 [RX SAVE]
#3 [TX SAVE]
#4 [TOT]
#5 [ON TIMER]
#6 [OFF TIMER]
#1 [ARTS BEEP]
#2 [ARTS INTERVAL]
#3 [CW ID]
#1 [BCLO]
#2 [HOME/REV]
#3 [MON/T-CAL]
#4 [MON-F CHANGE]
#5 [EMG SET]
#6 [HALF DEVIATION]
#7 [VOX SENS]
#8 [VOX DELAY]
#9 [BAND LINK]
#10 [VFO MODE]
#11 [FONT EDITOR]
#12 [ICON SET]
#13 [ICON EDITOR]
#14 [ICON SELECT]
#15 [CLOCK SHIFT]
#16 [TIME SET]
#17 [LANGUAGE]
#18 [ATT]
#19 [MIC MONITOR]
#20 [WX ALERT]
TSQ/DCS/DTMFScan ModesMeasurementSave ModesARTSMisc Setup