98/99™ Series Exit devices
Introduction Exit devices are a critical part of the fire and life safety egress system and will provide safe and reliable service when properly applied and maintained. Von Duprin designs and manufactures exit devices in accordance to ISO 9001 Quality Management System and meets or exceeds accepted U.S. domestic and International standards. All 98 and 99 Series exit devices are UL listed for panic hardware or fire hardware, and are certified to ANSI A156.3, 2001, Grade 1.
Table of contents Exit hardware Fire exit hardware Rim devices Rim devices 98/99E 8 98-F/99E-F 10 Trim 9 Trim 11 Mortise lock devices Mortise lock devices 875/9975 12 9875-F/9975-F 14 Trim 13 Trim 15 Surface mounted Vertical rod devices Surface mounted Vertical rod devices 9827/9927 16 9827-F/9927-F 18 Trim 17 Trim 19 Three-point latching devices Three-point latching devices 9857/9957 20 9857-F/9957-F 22 Trim 21 Trim 23 Concealed vertical rod devices Concealed vert
Options and accessories Applications & trim operation Single & double door applications Door handing outside trim operation Lever styles Trim options Knob Thumbpiece Lever Electrified outside lever trim (E996L) Breakaway lever Thumbturn control Hospital pull Offset pull Vandal resistant pull AD-Series adaptable electronic trim Strike options Strike/Stile information Strikes Dogging options Cylinder dogging Hex key dogging Less dogging Dogging keys Special center case dogging Double cylinder Electric
Nomenclature – how to order EL None SD CD CX E QEL EL LX RX RX2 SS AX Standard Special dogging R/VR - panic only Cylinder dogging - panic only Chexit Electric locking mortise/lever Quiet electric latch retraction Electric latch retraction Latch bolt monitoring Request to exit Double request to exit Signal switch Accessible device PL PN WS XP Pullman latch Pneumatic latch retraction Surface vertical rod exit device Heavy protection - rim WS Tornado & hurricane tested 98 99 Series 98-smooth Series 99-
Popular double door applications Single door applications Double door applications Mortise lock and surface mounted or concealed vertical cable/rod device combination—same direction Single rim device Single mortise lock device Two rim devices with mullion— same direction Two vertical rods—double egress Door handing Left hand-reverse Left Hand-Reverse orientation Right hand-reverse Right Hand-Reverse orientation Orientation Orientation LHR RHR hand reverse) (Left(Left hand-reverse) (Right hand
Lever styles Decorative levers M51 Knurling available M52 Knurling available M53 M54 M55 M56 M57 •• M61 (Handed) M62 •• (Handed) M63 (Handed) M81 Knurling available M82 M83 M84 M85 (Handed) •• Available in Stainless Steel substrate ONLY. Standard Levers 01 02 Knurling available 03* Knurling available 05 06* Default lever Knurling available 07 12 (Handed) 16 (Omega) 17* Knurling available 18 ACC (Accent) (Handed) AST (Asti) (Handed) MER (Merano) (Handed) STA (St.
98/99 Rim exit device The 299 Strike ships standard, optional strikes available 98 and 99 Rim exit devices for all types of single and double doors with mullion, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 98 device has a smooth mechanism case and the 99 device has a grooved case. The rim device is non-handed except when the following device options are used: SD (special dogging), -2 (double cylinder) or SS (signal switch).
Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required 98EO 99EO 98DT 99DT 98NL 99NL 98NL-OP 99NL-OP — 990DT 990NL-R/V 110NL-MD 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — Pull center to center — 5 /2" (140mm) 5 /2" (140mm) — Projection 2" (51mm) 2" (51mm) — Product description Trim description Escutcheon plate size —
98-F/99-F Rim exit device The 299F Strike ships standard, optional strikes available 98-F and 99-F Rim fire exit devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors with 9954 or 9854 mullion, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required 98EO-F 99EO-F 98DT-F 99DT-F 98NL-F 99NL-F 98NL-OP-F 99NL-OP-F — 990DT 990NL-R/V 110NL-MD 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — Pull center to center — 5 /2" (140mm) 5 /2" (140mm) — Projection 2" (51mm) 2" (51mm) — Product descr
9875/9975 Mortise lock device 7500 Mortise Lock 9875/9975 Mortise lock device for all types of single or double doors, UL listed for Panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4 3/4" (121mm). The 9875 device has a smooth mechanism case and the 9975 device has a grooved case. The mortise lock device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch).
Standard trim EO DT NL HL No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Hospital latch Key locks & unlocks Product description 9875EO 9975EO 9875DT 9975DT 9975NL 9875NL 9875HL Trim description — 990DT 990NL-M HL6M — 3" x 14 3/16" x 3/32" (76x360x2mm) 3" x 14 3/16" x 3/32" (76x360x2mm) 2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) – Projection 2" (51mm) 2"
9875-F/9975-F Mortise lock fire exit device 9875-F/9975-F Mortise lock fire exit device 9875-F/9975-F Fire exit mortise lock devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors installations, UL listed for fire exit hardware; See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. Fits door stiles as narrow as 4 3/4" (121mm).
Standard trim DT NL HL No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Hospital latch Key locks & unlocks Product description 9875EO-F 9975EO-F — — 9875NL-F 9975NL-F 9875HL-F 9975HL-F Trim description — 990DT 990NL-M HL6M — 3" x 14 3/16" x 3/32" (76x360x2mm) 3" x 14 3/16" x 3/32" (76x360x2mm) 2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm) Pull center to center — 5 1/2" (140mm) 5 1/2" (140mm) – Projection 2" (51mm)
9827/9927 Surface mounted vertical rod device Top latch 299 Top strike 9827/9927 Surface mounted vertical rod device 9827/9927 Surface mounted vertical rod device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9827 device has a smooth mechanism case and the 9927 device has a grooved case.
Standard trim EO DT NL NL-OP TL TL-BE Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) 9827EO 9927EO 9827DT 9927DT 9827NL 9927NL 9827NL-OP 9927NL-OP 9827TL 9927TL 9827TL-BE 9927TL-BE — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) 1
9827-F/9927-F Surface Mounted Vertical Rod Fire Device Top latch 9827/9927 Surface mounted vertical rod device 299 Top strike 9827-F/9927-F Fire exit surface mounted vertical rod device pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9827-F device has a smooth mechanism case and the 9927-F device has a grooved case.
Standard trim TL-BE Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9827NL-F 9927NL-F 9827NL-OP-F 9927NL-OP-F 9827TL-F 9927TL-F 9827TL-BE-F 9927TL-BE-F 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 1 11/16" x 7 1/2" x 7/8" (43x191x22mm) 1 11/16" x 7 1/2" x 7/8" (43x191
9857/9957 Three-point latching device Top latch 299 Top & middle strike 9857/9957 Three-point latching device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9857 device has a smooth mechanism case and the 9957 device has a grooved case. The three-point latching device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch).
Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9857EO 9957EO 9857DT 9957DT 9857NL 9957NL 9857NL-OP 9957NL-OP 9857TL 9957TL 9857TL-BE 9957TL-BE — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT
9857-F/9957-F Three-point latching fire exit device Top latch 9857-F/9957-F Three-point latching fire exit device 299 Top & middle strike 9857-F/9957-F Fire exit three-point latching device for all types of single doors up to 4' x 8' (1219mm x 2438mm) or up to 8' x 8'(2438mm x 2438mm) double doors with 9954 or 9854 mullion, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9857EO-F 9957EO-F 9857DT-F 9957DT-F 9857NL-F 9957NL-F 9857NL-OP-F 9957NL-OP-F 9857TL-F 9957TL-F 9857TL-BE-F 9957TL-BE-F — 990DT 990NL-R/V 110NL-MD 110NL-WD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 1
9847/9947 Concealed vertical rod device Top Latch 338 Top Strike 9847/9947 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847 device has a smooth mechanism case and the 9947 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch).
Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9847EO 9947EO 9847DT 9947DT 9847NL 9947NL 9847NL-OP 9947NL-OP 9847TL 9947TL 9847TL-BE 9947TL-BE Trim description — 990DT 990NL
9847-F/9947-F Concealed vertical rod fire exit device Top Latch 9847-F/9947-F Concealed vertical rod fire exit device 338 Top Strike 9847-F/9947-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9847EO-F 9947EO-F — — 9847NL-F 9947NL-F 9847NL-OP-F 9947NL-OP-F 9847TL-F 9947TL-F 9847TL-BE-F 9947TL-BE-F Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360
9848/9948 Concealed vertical rod device Top Latch 338 Top Strike 9848/9948 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Covers stock hollow metal doors with 86 or 161 cutouts. Devices are ANSI A156.3 – 2001 Grade 1. The 9848 device has a smooth mechanism case and the 9948 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used:SD (special dogging), or SS (signal switch).
Standard trim EO DT NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9848EO 9948EO 9848DT 9948DT 9848NL 9948NL 9848NL-OP 9948NL-OP 9848TL 9948TL 9848TL-BE 9948TL-BE Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T
9848-F/9948-F Concealed vertical rod fire exit device Top Latch 9848-F/9948-F Concealed vertical rod fire exit device 338 Top Strike 9848-F/9948-F Concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm), UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9848-F device has a smooth mechanism case and the 9948-F device has a grooved case.
Standard trim EO DT NL NL-OP TL TL-BE Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) Product description 9848EO-F 9948EO-F — — 9848NL-F 9948NL-F 9848NL-OP-F 9948NL-OP-F 9848TL-F 9948TL-F 9848TL-BE-F 9948TL-BE-F Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT — 3" x 14 13/16" x 3/32" (76x360
9849/9949 Concealed vertical cable device Top latch 338 Top strike retrofit bracket 9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch).
Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849EO 9949EO 9849DT 9949DT 9849NL 9949NL 9849NL-OP 9949NL-OP Trim description — 990DT 990NL-R/V 110NL-MD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — — 2" (51mm) 2" (51mm) — AN
9849-F/9949-F Concealed vertical cable fire exit device Top latch 9848-F/9948-F Concealed vertical rod fire exit device 338 Top strike retrofit bracket 9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case.
Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849EO-F 9949EO-F — — 9849NL-F 9949NL-F 9849NL-OP-F 9949NL-OP-F Trim description — 990DT 990NL-R/V 110NL-MD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center
9847WDC/9947WDC Wood door concealed vertical rod device Top Latch 9847WDC/9947WDC Wood door concealed vertical rod device 338 Top Strike 9847WDC/9947WDC Concealed vertical rod device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case.
Standard trim EO DT NL NL-OP TL TL-BE Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) 9847WDC-EO 9947WDC-EO 9847WDC-DT 9947WDC-DT 9847WDC-NL 9947WDC-NL 9847WDCNL-OP 9947WDCNL-OP 9847WDC-TL 9947WDC-TL 9847WDC-TL-BE 9947WDC-TL-BE — 990DT 990NL-R/V 110NL-WD 376TWDC x 990DT 376TWDC-BE x 990DT — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" — (76x360x2mm)
9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device Top Latch 9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device 338 Top Strike 9847WDC-F/9947WDC-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO Trim description NL NL-OP TL TL-BE No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Thumbturn Key locks & unlocks (use with DT trim) Thumbturn Blank escutcheon always operable (no cylinder) (use with DT trim) 9847WDC-EO-F 9847WDC-DT-F 9847WDC-NL-F 9847WDCNL-OP-F 9847WDC-TL-F 9847WDC-TL-BE-F 9947WDC-EO-F 9947WDC-DT-F 9947WDC-NL-F 9947WDCNL-OP-F 9947WDC-TL-F 9947WDC-TL-BE-F
9849WDC/9949WDC Wood door concealed vertical cable device Top latch 9849WDC/9949WDC Wood door concealed vertical cable device 338 Top strike retrofit bracket 9849WDC/9949WDC Concealed vertical cable device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case.
Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849WDC-EO 9949WDC-EO 9849WDC-DT 9949WDC-DT 9849WDC-NL 9949WDC-NL 9849WDC-NL-OP 9949WDC-NL-OP Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Pr
9849WDC-F/9949WDC-F Wood door concealed vertical cable fire device Top latch 9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device 338 Top strike retrofit bracket 9849WDC-F/9949WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9849WDC-EO-F 9949WDC-EO-F — — 9849WDC-NL-F 9949WDC-NL-F 9849WDC-NL-OP-F 9949WDC-NL-OP-F Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate
9850WDC/9950WDC Wood door concealed vertical cable device Top latch 9850WDC/9950WDC Wood door concealed vertical cable device 338 Top strike retrofit bracket 9850WDC/9950WDC Concealed vertical cable device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9850WDC device has a smooth mechanism case and the 9950WDC device has a grooved case.
Standard trim DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9850WDC-EO 9950WDC-EO 9850WDC-DT 9950WDC-DT 9850WDC-NL 9950WDC-NL 9850WDC-NL-OP 9950WDC-NL-OP Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate size Pull center to center — Pr
9850WDC-F/9950WDC-F Wood door concealed vertical cable fire device Top latch 9850WDC-F/9950WDC-F Wood door concealed vertical rod fire device 338 Top strike retrofit bracket 9850WDC-F/9950WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1.
Standard trim EO DT NL NL-OP No outside trim Exit only Dummy trim Pull when dogged (not recommended for fire device) Night latch Key retracts latchbolt Night latch Key retracts latchbolt optional pull required Product description 9850WDC-EO-F 9950WDC-EO-F — — 9850WDC-NL-F 9950WDC-NL-F 9850WDC-NL-OP-F 9950WDC-NL-OP-F Trim description — 990DT 990NL-R/V 110NL-WD — 3" x 14 13/16" x 3/32" (76x360x2mm) 3" x 14 13/16" x 3/32" (76x360x2mm) — 5 1/2" (140mm) 5 1/2" (140mm) — Escutcheon plate
98/99 Optional trim Knob, exit only and thumbpiece trim – 990 & 996K K-NL K Knob Key locks & unlocks Trim 996K description Knob – night latch Key retracts latchbolt 996K-NL K-BE Knob – blank escutcheon Always operable (no cylinder) 996K-BE K-DT Knob – dummy trim Pull when dogged 996K-DT EO Exit only plate 996EO TP Thumbpiece Key locks & unlocks 990TP TP-BE EO Thumbpiece blank escutcheon Always operable (no cylinder) Exit only plate 990TP-BE 990EO Escutcheon 23/4" x 103/4" x 27/32" 23
98/99 Optional trim Optional trims – 696 DT NL TP TP-BE Dummy trim Pull when dogged (not recomended for fire device) Night latch Key retracts latchbolt Thumbpiece Key locks & unlocks Trim description 696DT 696NL 696TP 696TP-BE Escutcheon plate size 23/4" x 103/4" x 27/32" (70x273x21mm) 23/4" x 103/4" x 27/32" (70x273x21mm) 15/8" x 131/2" x 3/16" (41x343x5mm) 15/8" x 131/2" x 3/16" (41x343x5mm) Pull center to center 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) 51/2" (140mm) Projection 2 /
98/99 Optional trim E996L Electrified breakaway lever 392-7 Offset pull The 392-7 Offset pull is 3/4₄" round stainless steel, with a 7" center to center which matches the 98/99 center case. Often used with a night latch operation. 3 1/2" (89mm) offset with 1 1/2₂" (38mm) clearance. E996L Electrified lever trim provides remote locking and unlocking. Furnished standard in fail safe (FS) condition, can be field converted to fail secure (FSE) where allowed.
98/99 Optional trim This page intentionally left blank Trim options Von Duprin 98/99 Series • 51
Schlage AD-Series AD-Series adaptable electronic locks Standalone locks are a cost-effective solution for doors that do not require real-time monitoring. The AD-Series standalone solution provides: There are a variety of options that allow you to select the AD-Series electronic lock that’s right for you, and a wide selection of features that can be configured in the field to further customize each opening.
Schlage CO-Series CO-Series electronic locks from Schlage In the world of standalone electronic locks, nothing compares to the CO-Series from Schlage. And because CO-Series locks offer a wide variety of options, it’s easy to find the right solution for any facility. For openings with a relatively small number of users, we recommend the C0-100. It’s an offline keypad programmable lock. For larger applications try the CO-200 or CO-250. They’re computer programmable locks that can provide audit trails.
98/99 Strike/Stile information Device type Standard single door Strike Trim/Stile 990/996 98/99 XP 98/99 98-F/99-F XP98-F/XP99-F Strike options / Dogging options 9875 9975 4 3/8" (111mm) Strike Strike w/mullion* Trim/Stile 299 x 4954 299F 909 Strike Application PL9827/PL9927 Pullman latch 299 (Top) 304L/248-L-4 (Bottom) 9827-F 9927-F 299 (Top) 304L (Bottom) 9847 9947 9848 9948 338 (Top) 385A (Bottom) 338 (Top) 385A (Bottom) 338 (Top) 385A (Bottom) 299F 499F x 9954 304L 4 7/8" (124mm)
98/99 Strike information Strikes for rim devices 264 299 299F 499F 1408 Projection 9/16" (14mm) Projection 13/16" (21mm) Projection 13/16" (21mm) Projection 15/16" (24mm) One per pair of doors 1439–Blade stop 1410–Integral stop 1606 1609 Projection 1/2" (13mm) Projection 1/2" (13mm) Projection 3/8" (10mm) Panic devices only – Requires coordinator – For panic exit application only, not fire rated Strikes for vertical cable devices 909 249 - Top249 strike 954 1" (25 mm) 349 349 - Botto
98/99 Dogging options CD Cylinder dogging SD Special center case dogging Cylinder dogging is available on all 98/99™ Panic exit devices to replace the standard hex key dogging. Unit requires a standard 1 3/4" (32mm) mortise cylinder with an inverted straight cam (Schlage Cam B502-191 reference). Special cylinder dogging in the center case is available for Chexit, EL, QEL, ALK panic devices to allow for mechanical push/pull operation.
98/99 Electrical options RX Request to exit The RX (2xit) feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the pushpad. The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply. The RX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resisitive maximum). The RX switch is available in a low current (LC) switch.
98/99 Electrical options CX The Chexit® Internal horn: Whenever the device is in alarm or the push pad is pressed the internal horn will sound. The volume level of this horn exceeds 85 db at 6 feet. Door position input: An external door position switch can be connected to the Chexit. Designed for use on delayed exit applications, the Chexit system is ideal for controlled areas.
98/99 Electrical options Chexit typical application Chexit single door with options – The Chexit is used as an access control device. The card reader allows access. Also shown in this application is an external horn and door position switch. The auxiliary horn is used for increased volume in remote locations. Using a door position switch gives added security to the opening in case the door is not reclosed. With the Chexit disarmed, the opening functions as a normal exit device.
98/99 Electrical options E Electric mortise lock device Electrical options & accessories The electric mortise lock device has all the versatility and advantages of the standard mortise lock device, plus the advantage of being electrically controlled by a remote switching device, an access control system or an automatic fire alarm system. The device features the E7500 mortise lock. The E7500 controls the locking of the outside trim.
98/99 Electrical options EL Electric latch retraction QEL Quiet electric latch retraction If manual hex-key dogging is required, specify HD-EL. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-EL. SD-EL is not available on the 9875 or 9975 devices.
98/99 Electrical options Power Supplies Series PS902/914 PS902 PS904 PS906 PS914 Number of connectors on power supply for the following: 2 amps 4 amps 6 amps 4 amps Distribution boards 1 2 3 2 Battery back-up board 1 1 1 1 Note: One fire alarm board can be connected directly to the PS902. If a fire alarm board is desired for the PS904, PS906 or PS914 it can be connected to a distribution board.
98/99 Electrical options EPT Electrical power transfer PNT Pneumatic transfer Electric Power Transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideal for installations involving abuse or heavy traffic. Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and EPT-10 are U/L listed as “miscellaneous door accessory”.
98/99 Mechanical options AX Accessible device The AX device is a UL certified exit device designed to meet the progressive requirements of the California Building Code for accessible openings. This device meets the 5 lbs of operating force requirement called for in chapter 11B-309.4. The AX device also exceeds ANSI/BHMA requirements. Available devices include: AX98/99, AX98/99-F, AX98/9949LBL, AX98/9949-F LBL, AX98/9949-F LBLAFL.
98/99 Mechanical options Dummy pushpad The 330 dummy pushpad is designed as a companion unit for all 99 devices. The 350 dummy pushpad is a companion unit for all 98 devices. The pushpad is rigid or nonfunctioning. A push/pull operation can be accomplished by using 990DT, 996DT trim or any Ives Pull. The 330/350 can be equipped with a functional pushpad and will accommodate an RX or WP-RX switch. Specify RX-330. May also be equipped with the RX2, double RX switch. Specify RX2-330 To order, specify: 1.
98/99 Mechanical options PN Pneumatic controlled exit devices Mechanical options & accessories The PN feature provides remote latch bolt retraction in hazardous areas where electrically operated devices would not be permitted. The pneumatic solenoid will retract the latch bolt for momentary or prolonged periods. PN exit devices are particularly suited for use with automatic door operators. The PN feature is available on both Panic and fire exit hardware devices.
98/99 Device options & accessories RG-27 Vertical rod and latch guard Series RG-27 Vertical rod and latch guards protect the bottom rods of exit devices from the damaging impacts of carts or gurneys passing through doors. (If bottom rods become damaged, the exit device will not function as intended and can jeopardize the ability to exit safely during an emergency.
98/99 Device options & accessories Cylinders Cylinders are not furnished with device or trim and must be specified when ordering. Refer to trim pages for cylinder type.
98/99 Device options & accessories Mullions Removable steel mullions provide single door performance in double door openings with rim devices. Mullions are easily removed by loosening bottom set screw and removing top fitting cover. The top mullion fitting is attached to the frame and is concealed by the fitting cover. Steel mullions are 2" (51mm) wide and 3" (76mm) deep, with a wall thickness of 1/8" (3mm). Mullions are shipped with mounting screws and prepared for strikes.
98/99 Device options & accessories Sex bolts 325 sex bolts used on surface Vertical Latches. Sex bolts when ordered with devices may be furnished with screw lengths different than shown in Column B. Below, Column B indicates popular sizes. Sex Bolts ordered separately are not furnished with screws. If screws are required refer to chart below and order screws by description as a separate item. Other screw lengths may be used based on minimum and maximum allowable thread engagement, shown in column “C.
98/99 Function, grade, type options ANSI Function, grade & type Function Grade 1, type 1 Grade 1, type 2 Grade 1, type 3 Grade 1, type 7 Grade 1, type 7 Grade 1, type 8 Grade 1, type 8 Grade 1, type 8 Grade 1, type 9 1 98EO & F 99EO & F 9827EO & F 9927EO & F 9875EO & F 9975EO & F 9847WDCEO & F 9947WDCEO & F 9849WDCEO & F 9949WDCEO & F 9847EO & F 9947EO & F 9848EO & F 9948EO & F 9849EO & F 9949EO & F 9857EO & F 9957EO & F 2 98DT 99DT 9827DT 9927DT 9875DT 9975DT 9847WDCDT 9947WDCDT 984
UL Listing for fire exit hardware UL Listed fire exit hardware label and opening size Double door Door material With 9954 Single door mullion With 9854 mullion With kr9954 mullion With kr9854 mullion Vxv V x mortise Vxv same direction same direction double egress 98-F 99-F Metal 3 Hour 4' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 8' 3 Hour 8' x 8' — — — 9875-F 9975-F Metal 3 Hour 4' x 10' — — — — — 3 Hour 8' x 10' — 3 Hour 8' x 10' 3 Hour 8' x 10' Additional information
98/99 Finishes A. Center case cover B. Touch bar end cap C. Touch bar trim D. Cover plate E. Mechanism end cap F.
98/99 Finishes Finishes* US number BHMA number Color US number BHMA number Chromium, polished US26 625 Bronze, dull US10 612 Anodized, aluminum US28 628 US15 619 Chromium, dull US26D 626 Satin stainless steel US32D 630 Brass, polished US3 605 Duranodic dark bronze 313 710 Brass, dull US4 606 Black 315 711 Finishes Color Satin nickel Available for 35A ONLY Special finishes Color US number BHMA number Satin chrome, Antimicrobial US26DAM 626-AM Satin stainless steel,
About Allegion Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security. As a $2 billion provider of security solutions for homes and businesses, Allegion employs more than 7,800 people and sells products in more than 120 countries across the world. Allegion comprises 23 global brands, including strategic brands CISA®, Interflex®, LCN®, Schlage® and Von Duprin®. For more, visit www.allegion.com © 2014 Allegion 006590, Rev. 04/14 www.allegion.