PMC-05P3/E 03.8.
PMC-05P3/E 03.8.19 2:58 PM ページ 1 CONGRATULATIONS! Thank you for your purchasing the VESTAX PMC-05ProIII, Professional Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safely and in the knowledge of all its special features and suitable applications.
PMC-05P3/E 03.8.19 2:58 PM ページ 10 IMPORTANT SAFEGUARDS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions-The safety and operating instructions should be retained for future reference. 3.
PMC-05P3/E 03.8.19 2:58 PM ページ 3 16. Replacement Parts-When replacement parts are 18. Carts and Stands-The appliance should be used required, be sure the service technician has used only with a cart stand that is recommended by replacement parts specified by the manufacturer manufacturer. or have the same characterristics as the original parts. Unauthorized substitutions may result in 19. An appliance and cart combination should be fire, electric shock or other hazards. moved with care.
PMC-05P3/E 03.8.
PMC-05P3/E 03.8.19 2:58 PM ページ 5 qMAIN MIC LEVEL Adjusts the input level of the MAIN MIC input. wMIC EQs Adjusts the HI and LOW frequencies for both the MAIN and SUB MIC input. eMIC PAN Adjusts the panning for both the MAIN and SUB MIC. rTRIM (PGM1/PGM2) Adjusts the input level of each channel. For optimal acoustic quality, set the INPUT FADER to a position of 7 or 8 then adjust the TRIM so that a sufficient signal is fed through the channel without distorting.
PMC-05P3/E 03.8.19 2:58 PM ページ 6 FRONT PANEL @1 PHONE JACK @3 EFFECT SEND JACK Connect the headphones with the impedance of 8ohm to 600ohm. Connect to the input of the external effects. (Delay, Reverb etc) @2 EFFECT RECEIVE JACK Connect to the output of the external effects. REAR PANEL 31 24 25 30 29 27 28 26 connected, the signal from the turntable is fed to the respective PGM when the Phono Input is selected. @4 SUB MIC LEVEL Adjusts the input level from SUB MIC IN.
PMC-05P3/E 03.8.19 2:58 PM ページ 7 HOW TO CHANGE THE FADER UNIT q Remove the fader knobs. (See fig-a) w Remove the 4 screws which fix the top panel. (See fig-a) e Remove the 2 screws which fix the fader panel, and remove the fader unit from position in mixer. (See fig-b) r Carefully remove the multi-cable connector from the fader unit. t Remove the fader knob of new fader unit. y Attach multi-cable connector to new fader unit. (See fig-c/d) u Position the new fader unit carefully and secure with screws.
PMC-05P3/E 03.8.19 2:58 PM ページ 4 HOW TO CHANGE INPUT SELECT SWITCH e Carefully remove the multi-cable connector from the switch unit. (See fig-f) q Remove the top panel in the same procedure. (See fig-a) w Remove the 2 screws which fix the switch panel, fix the r Attach multi-cable connector to new switch unit. switch panel, and remove the switch unit from t Position the switch unit carefully, and secure with position in mixer. (See fig-e) screws.
PMC-05P3/E 03.8.
PMC-05P3/E 03.8.19 2:58 PM ページ 2 SPECIFICATION INPUT SECTION NOMINAL INPUT LEVEL IMPEDANCE MIC -54dBv 3.3kΩ LINE -10dBv 10kΩ PHONO -42dBv 56Ω RCV -10dBv 10kΩ NOMINAL OUTPUT LEVEL IMPEDANCE -10dBv 2kΩ 58mW MAX(@47Ω) ≧8Ω ‐10dBv 2kΩ LINE OUTPUT SECTION PHONES SEND FREQUENCY RESPONSE 25Hz∼25kHz CROSS TALK ≧100dB SN RATIO ≧75dB THD <0.01% DIMENSION (WxHxD) 262 (W) x 106 (H) x 370 (D) WEIGHT 3.
PMC-05P3/E 03.8.19 2:58 PM ページ 11 AUG.