VESTEL WASHING MACHINE USER MANUAL CMH-XXL 9412 TKE - CMH-XXL 9412 TGE
CONTENTS CHAPTER-1: TECHNICAL SPECIFICATIONS CHAPTER-2: BEFORE USING WASHING MACHINE Safety warnings Recommendations CHAPTER-3: SETTING UP .....
CHAPTER -1: TECHNICAL SPECIFICATIONS 2 3 4 1 1.Detergent drawer 2.Upper tray 3.Programme knob 4.Electronic display 5.Door 6.Cover of pump filter 5 6 8 9 10 7 7 7.Transport safety screw 8.Power cable 9.Discharging hose 10.
CHAPTER -1: TECHNICAL SPECIFICATIONS Operating voltage / frequency (V/Hz) (220-240) V ~/60Hz 10 Total current (A) Maximum: 1 Mpa Minimum: 0.
CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS SAFETY WARNINGS Do not use multiple receptacles or extension cord. Do not plug in damaged or torn plugs. In case of a breakdown of power cable, contact the nearest authorized service for replacing it. Never pull the cable when unplugging. Grab the plug when unplugging. Do not plug-in or out the plug from the receptacle with wet hands to prevent electric shock. Never touch the machine with your wet, damped hand or foot.
CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS / RECOMMENDATIONS You should absolutely remove the transport screws of your machine before the first usage. Faults occurring in the machines operated with transport screw fitted shall be out of scope of warranty. Do not put discharging hose of your machine in a vessel, bucket or sink. Your machine is out of warranty against faults caused by any kind of external factors (spate, pesticides, fire, etc.).
CHAPTER -3: SETTING UP REMOVING TRANSPORT SAFETY SCREWS Before operating your washing machine, you should certainly remove the transport safety screw on the rear side of the machine. For this reason, transport safety screws shall be loosened by being rotated in counter-clockwise using an appropriate wrench.
CHAPTER -3: SETTING UP REMOVING TRANSPORT SAFETY SCREWS Transport screws shall be removed by pulling out. Fit the plastic transport screw taps delivered in accessories bag to the places where transport screws have been removed. The transport safety screws should be stored to be used in case of a transportation. You should absolutely remove the transport screws of your machine before the first usage. Faults occurring in the machines operated with transport screw fitted shall be out of scope of warranty.
CHAPTER -3: SETTING UP ADJUSTING ADJUSTABLE STAYS Do not install your machine on a carpet or suchlike grounds. To ensure silent and vibration-free operation of your machine, it should be deployed on a non-sliding and firm ground. Loosen the plastic adjustment nut. Adjust the stays upward and downward by rotating them. After maintaining the balance, compress the plastic adjustment nut upward again.
CHAPTER -3: SETTING UP ELECTRICAL CONNECTION / WATER INLET CONNECTION Electrical connection Your washing machine is set to 220-240V and 60Hz. Mains cord of your washing machine is equipped with a specific grounded plug. This plug should always be inserted to a grounded receptacle of 10 amperes. Fuse current value of the power line connected to this plug should also be 10 amperes. If you don’t have such a receptacle and fuse confirming with this, please have it done by a qualified electrician.
CHAPTER -3: SETTING UP WATER INLET CONNECTION / WATER D SCHARGE CONNECTION Water discharge connection Ensure that water discharge hose is not folded, twisted, crushed or elongated. Water discharge hose can be fitted minimum 60 cm and maximum 100 cm above the ground. The end of water discharge hose can be fitted to a specific apparatus directly attached to dirty water discharge hole or outlet joint of the basin elbow. Never attempt to extend the water discharge hose by jointing.
CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING SEPARATING LAUNDRIES Separate your laundries according to their types (cotton, synthetic, sensitive, woollen, etc.), their temperatures (cold, 30°, 40°, 60°, 90°) and degree of contamination (slightly stained, stained, highly stained). Never wash your coloured and white laundries together. Wash your coloured laundries separately in the first washing as they may bleed.
CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING SEPARATING LAUNDRIES Ironing temperature is maximum 110°C Whitening available No whitening Ironing temperature is maximum 150°C Ironing temperature is maximum 200°C Dry cleaning available No dry cleaning Hang when wet Dry by hanging Drying by twirling is not allowed Dry cleaning in gas oil, pure alcohol and R113 is allowed Perchloroethylen e R11, R113, Petroleum Perchlorinetyhlene R11, R113, Gas oil 13 No ironing Leave on a flat place
CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING PUTTING LAUNDRIES IN THE MACHINE Open the door of your machine. Spread your laundries in your machine. Note: Maximum loading capacity may vary based on the laundry type you will wash, degree of contamination and the programme you have chosen. Do not exceed maximum dry loading capacity indicated in the programme table for washing programmes. You can take the following table of weights as an example.
CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING ADDING DETERGENT INTO MACHINE The amount of detergent you will put in your machine will depend on the following criteria: Your detergent utilization will be based on the degree of contamination of your laundries. Do not prewash your less stained laundries and put your slight amount of detergent in the 2nd compartment of the detergent drawer.
1-Detergent drawer 2-Programme knob 3-Electronic display and auxiliary functions 1 2 3 CHAPTER 5: CONTROL PANEL 16
CHAPTER 5: CONTROL PANEL DETERGENT DRAWER E D B A C A. Prewashing compartment B. Main washing compartment C. Softener compartment D. Siphon cover E.
CHAPTER 5: CONTROL PANEL PROGRAMME KNOB You may select the programme you like to wash your laundries through programme knob. You may set the programme selection operation by rotating the programme knob in both direction. Ensure that the programme knob is exactly on the programme you want to select.
CHAPTER 5: CONTROL PANEL ELECTRONIC DISPLAY 1-Adjusting button for revolution speed 2-Adjusting button for temperature of washing water 3-Auxiliary function prewash 4-Auxiliary function for rapid wash 5-Auxiliary function for easy ironing 6-Auxiliary function for delay timer 7-Start/Pause button 8-Electronic display On the electronic display, you may view washing water temperature, wringing revolution speed of your machine, the amount time your machine will continue washing, the auxiliary functions you hav
CHAPTER 6: OPERATING YOUR MACHINE Plug your machine in. Open the water faucet. Open the machine door. Spread your laundries in your machine. Push the door of your machine until hearing the locking sound to close it. Put detergent and softener in the detergent drawer. First washing operation Some water may be left in your machine due to experiments and tests carried out during production.
CHAPTER 6: OPERATING YOUR MACHINE Half-load detection system Your machine features a half-load detection system. In case you put approximately half or less amount of laundries of maximum laundry capacity in your machine, your machine will run so as to save washing time, water consumption and energy in some programmes (White cotton 95°, Colorfast cotton 60°, Non colorfast cotton 40°). When halfload function is active, the machine can complete the programme you have set in a shorter time.
CHAPTER 6: OPERATING YOUR MACHINE PROGRAM TABLE PROGRAMME TEMPERATURE (°C) DETERGENT COMPARTMENT MAXIMUM AMOUNT OF DRY LAUNDRY (kg) LAUNDRY TYPE Very dirty cotton and flax textiles. (Underwears, linen, tablecloth, towel (maximum 4 kg), bedclothes, etc. Dirty cotton and flax textiles. (Underwears, linen, tablecloth, towel (maximum 4 kg), 2- COTTON 60 2 9 bedclothes, etc. Dirty cotton and flax textiles. (Underwears, linen, tablecloth, towel (maximum 4 kg), 3- COTTON 40 2 9 bedclothes, etc.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 1-Revolution speed selection and auxiliary function of soaking You can set the wringing revolution for your laundries via revolution speed setting button. When you select a new programme, the maximum wringing revolution speed of the programme you have selected will be viewed on the display of revolution speed.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS If this function is selected, your laundries will be soaked in the latest rinsing water. When your machine soaks your laundries in the latest rinsing water, symbol will blink on electronic display. If you want to take your laundries out, press on “Start / Pause” button. Your machine will empty the water in it and finish the programme without wringing.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 2-Washing water temperature selection You can select the washing water temperature with the washing water temperature adjustment button. Whenever you select a new programme, the maximum washing water temperature is shown on the washing water temperature display. You can gradually decrease the washing water temperature between the maximum temperature and cold washing (--) by pressing washing water temperature adjustment button.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 3-Auxiliary function prewash You can expose your very dirty laundries to prewashing operation prior to main washing by using this auxiliary function. When using this function, you should put detergent in front washing compartment of the detergent drawer. 4-Auxiliary function for rapid wash This auxiliary function will enable the washing duration of your laundries that are not very dirty to be shortened.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 6-Auxiliary function for delay timer By using this auxiliary function, you can let your machine start washing after half an hour to 23 hours. To use auxiliary function of delay timer: - Press time delay button once. - Expression of “0.5h” will appear on the display. - Press on time delay button until the time, on which you want washing operation to be started.
CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 7-Anti-Allergic auxiliary function In the programmes where this auxiliary function is active, your machine will perform an extra rinsing operation on your laundries prior to latest rinsing operation. Note: Anti-Allergic auxiliary function is selected automatically only in Hygiene programme.
CHAPTER 6: OPERATING YOUR MACHINE STARTING THE PROGRAMME Start/Pause button By pressing on Start/Pause button, you may start the programme you have selected, suspend a running programme. If you switch your machine to pause mode, electronic display will blink. When you start your machine, the following symbols for the programmes you have selected will be available on electronic display.
CHAPTER 6: OPERATING YOUR MACHINE ADDING/REMOVING LAUNDRY Laundry adding to / removing from the machine If you want to add or remove laundries when your machine is running: - Switch your machine to pause mode by pressing on Start/Pause button. moves over electronic - After a while, if you realize that symbol display, this means that the door of your machine will be convenient for opening. When you see symbol on electronic display, you can either add or remove laundries after opening the machine door.
CHAPTER 6: OPERATING YOUR MACHINE CHILD LOCK Child lock To avoid programme flow from being affected if programme knobs are pressed or programme knob is turned when performing washing operation in your machine, child lock is available. Child lock will be activated in case pressed on both auxiliary functions of quick washing and wrinkle removing at the same time in excess of 3 seconds. Symbol will flash on the electronic display when activated.
CHAPTER 6: OPERATING YOUR MACHINE CANCELLING PROGRAMME Cancelling programme If you want to cancel any programme running: - Switch the programme knob to 0. - Your machine will stop the washing operation and the programme will be cancelled. - To get rid of the water accumulated in the machine switch the programme knob to any programme. - Your machine will perform the necessary discharge operation and cancel the programme. - You can run your machine by selecting a new programme.
CHAPTER 6: OPERATING YOUR MACHINE FINISHING PROGRAMME Finishing programme - Your machine will stop by itself as soon as the programme you have selected finishes. -Expression of “END” will flash on the electronic display. Note: Within 2 minutes after the programme has finished, your machine will extinguish the electronic display to save energy. It will reflash when pressed on a button of any auxiliary function.
CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS WARNING OF WATER CUT-OFF / LOW MAINS WATER PRESSURE If symbol flashes on the electronic display: - Water faucet may be closed. Check. - Mains water may be cut-off. Check. If so, switch the programme knob to position 0. You can select a programme and run your machine after the mains water is supplied. - Mains water pressure may be low. Check. - Water inlet hose may be twisted. Check. - Water inlet hose may be clogged. Clean water inlet hose filters.
CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS WARNING OF CLOGGED PUMP FILTER If symbol flashes on the electronic display: - Pump filter may be clogged. Clean the pump filter. (*) - Discharging hose may be clogged or twisted. Check the discharging hose. (*) See the chapter regarding maintenance and cleaning of your machine.
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE Unplug your machine. Turn the water faucet off. WATER INLET FILTERS Filters to avoid dirt and foreign substances in the water from penetrating into the machine are available both on the side of faucet and on the ends of water valves along the water inlet hose of your machine. If your machine cannot intake sufficient amount of water despite water faucet being open, these filters should be cleaned. Detach the water inlet hoses.
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE / PUMP FILTER A filter system which avoids threads remaining from your laundries and tiny materials from entering into the pump during water discharging operation carried out by your machine after completing washing so prolonging the lifecycle of your pump is available. It is recommended that you clean your pump filter once in 2 months.
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE / PUMP FILTER After cleaning the filter, fit the filter cover by rotating it in clockwise. Fit the pump section of the toe board. Remember that water will leak if you do not fit the filter cover properly. You can use the pump section of the toe board for discharging slight amount of water remaining in the pump of your machine. WARNING! As water in the pump may be hot, wait until it cools down.
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE / DETERGENT DRAWER Your detergents may deposit residue in detergent drawer and housing of detergent drawer over time. To clean the residue formed, disassemble the detergent drawer in particular periods. To eject the detergent drawer: Pull the detergent drawer up to the end Keep on pulling by depressing on the flush cover in the detergent drawer already being pulled up to the end and then unsettle the detergent drawer. Flush it using a brush.
CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE / SIPHON PLUG / BODY / DRUM Siphon plug Disassemble the detergent drawer. Disassemble the flush stopper and clean the softener residues completely. Refit the flush stopper after cleaning it. Check whether it has settled properly. Body Clean the outer body of your machine with warm water and a noninflammable cleaning agent that will not abrade the body of your machine. After rinsing with some water, dry it using a soft and dry cloth.
CHAPTER -9: PRACTICAL INFORMATION Alcoholic drinks: Spotted area should initially be washed using cold water, and then be wiped with glycerine and water and rinsed with vinegar-mixed water. Shoe shine: Spot should be rubbed out gently without damaging the cloth and be scrubbed and rinsed with detergent. If not removed, it should be scrubbed using the mixture obtained by adding 1 scale of alcohol (96 ) into 2 scales of water, and then be washed with warm water.
CHAPTER -9: PRACTICAL INFORMATION Blood stain: Submerge your laundries in cold water for 30 minutes. If the stain is not removed, then submerge in a mixture of water and ammoniac (3 spoons of ammoniac in 4 litres of water) for 30 minutes. Cream, ice cream and milk: Submerge your laundries in cold water and scrub the spotted area with detergent. If the spot is not removed, apply bleacher to the extent suitable for your laundries. (Do not use bleacher for colour laundries.
CHAPTER -10: TROUBLESHOOTING All repairing operations required for your machine should be carried out by our authorised service. If your machine requires a repair or if you cannot remove the fault by the help of the information provided as follows: Unplug your machine. Turn the water faucet off. Contact the nearest authorised service. FAULT Your machine does not start. POSSIBLE CAUSE It is not plugged. Fuses out of order. Electricity cut-off. Start/pause button not pressed. Programme knob on position 0.
CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE Discharging hose clogged or twisted. Your machine does not discharge water. Pump filter clogged. Laundries settled in the machine nonhomogeneously. The stays of your machine not adjusted. Safety assembly fitted for transport not disassembled. Less amount of laundries in the appliance. REMOVING METHODS Check the discharging hose. Clean the pump filter. (*) Spread your laundries in the machine properly and homogeneously. Adjust the stays of your machine.
CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE Excessive amount of detergent used. Excessive foam is formed in the detergent drawer. Wrong detergent used.. The contamination degree of your laundries does not match the programme you have chosen. Unsatisfactory washing result. Amount of detergent used insufficient. Laundries in excess of maximum capacity put in your machine. 45 REMOVING METHODS Press on Start/Pause button.
CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE Water being hard. (Dirty, hard, etc.) Unsatisfactory washing result. Laundries distributed in your machine nonhomogenously. As soon as the machine is loaded with water, water discharges. No water appears in the drum during washing. The end of water discharging hose is too low for the machine. No fault. Water in the non-visible part of the drum. REMOVING METHODS Adjust the amount of detergent based on the instruction of detergent manufacturer.
CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE Wringing operation is not performed or runs late. No fault. Unbalanced load control system has been activated. 47 REMOVING METHODS Unbalanced load control system will try to spread your laundries homogeneously. Wringing operation will start after spreading your laundries. Put your laundries in the machine homogeneously in the next washing operation.
CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. TROUBLE CODE POSSIBLE FAULT WHAT TO DO E01 The door of your machine is left open. Close the machine door. If your machine persists to indicate fault, turn off your machine, unplug it and contact the nearest authorised service immediately.
CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE TROUBLE CODE POSSIBLE FAULT Water cut-off or low mains water pressure.. Pump is faulty or pump filter is clogged or electrical connection of the pump is faulty. 49 WHAT TO DO - Water faucet may be closed. Check. - Mains water may be cut-off. Check. - If so, switch the programme knob to position 0. You can select a programme and run your machine after the mains water is supplied. - Mains water pressure may be low. Check.
CHAPTER -12: DESCRIBING SAVING ENERGY Energy and water consumption may vary based on water pressure, water hardness, water temperature, ambient temperature, laundry amount, additional function selection, voltage fluctuations.
DISPOSAL OF YOUR OLD MACHINE This symbol on the product or package implies that the product should not be treated as domestic waste. Instead, it should be delivered to applicable waste collection places recycling electrical and electronic equipment. You will contribute to avoid potential negative results regarding environment and human health, which will arise due to wrong waste procedure for the product by ensuring that this product is annihilated properly.
CALL CENTER The lifetime of your product (the period during which the spare parts will be provided for its proper functioning) evaluated and announced by the Ministry of Customs and Trade is 10 years Producer Company: Vestel Beyaz Eşya Sanayi ve Ticaret A.Ş.
