VESTEL TELEViZYON KULLANIM KILAVUZU OPERATING INSTRUCTIONS PERFORMANCE 24VF3021 24” LED TV
İçindekiler GÜVENLİK ÖNLEMLERİ....................................................................1 Teknik Özellikler..................................................................................2 Desteklenen PC Girişi Tipik Ekran Modları.........................................2 Adım 1 – Uzaktan Kumandaya Pil Takılması.......................................2 Adım 2 - Kontrol Düğmesi...................................................................2 Adım 3 – Harici Cihazların Bağlanması ...............
Teknik Özellikler RF ANTEN GİRİŞİ 75 Ohm (dengeli olmayan) ÇALIŞMA GERİLİMİ 220-240V AC, 50 Hz. SES ÇIKIŞ GÜCÜ (WRMS.) (%10 THD): 2 x 2,5 GÜÇ TÜKETİMİ (W): 50 W (maks) < 1 W (Bekleme) PANEL 16:9 görüntü, 24” Ekran Boyutu BxUxY (Ayaklı): 135 x 579 x 408 Ağırlık (Kg): 5,20 BxUxY (Ayaksız): 35 x 579 x 372 Ağırlık (Kg): 4,80 Transmisyon Standartları: VHF (BANT I/III) UHF (BANT U) HİPERBANT Adım 1 – Uzaktan Kumandaya Pil Takılması 1.
APS sonlandıktan sonra ekranda program tablosu belirecektir. Program tablosunda, program numaralarını ve programlara verilen isimleri görürsünüz. Adım 4 – Güç ve Anten/Kablo Bağlantısı 75 ohm yuvarlak anten kablosu kullanınız. TV'nin ARKASI Giriş Seçimi Harici sistemleri TV’nize bağladıktan sonra farklı giriş kaynaklarına geçebilirsiniz. Kaynakları doğrudan değiştirebilmek için kumanda üzerindeki SOURCE tuşuna basınız.
Uzaktan Kumanda 1. Bekleme 2. Mono-Stereo/Dual I-II 3. Genişletme (TXT modunda)/Görüntü boyutu 4. Yeşil / Görüntü Menüsü 5. Kırmızı / Ses Menüsü 6. Rakam tuşları 7. Teleteks / Miks 8. İmleç sola 9. Menü açık / kapalı 10. AV / Kaynak 11. İşlev yok 12. Ses Seviyesini Artırma 13. Bilgi/Göster (TXT modunda) 14. Sessiz 15. Ses azaltma 16. Program aşağı 17. İşlev yok 18.
HDMI Gerçek Siyah TV HDMI kaynaktan izlenirken bu özellik Gelişmiş Ayarları menüsünde gösterilecektir. Görüntünün siyahlığını iyileştirmek için bu özelliği kullanabilirsiniz. HDMI Gerçek Siyah modunu etkinleştirmek için bu özelliği “Açık” olarak ayarlayabilirsiniz. Ses Menüsü Ses Ekolayzır Balans Ses Modu AVL Sıfırlama Sesi seviyesini ayarlar. Ekolayzır menüsünde önceki ayar Müzik, Film, Konuşma, Düz veya Kullanıcı olarak değiştirilebilir. Önceki menüye geri dönmek için “MENU” tuşlarına basınız.
Kaynak Menüsü TV’nize harici sistemler bağladıktan sonra, o kaynaktan görüntü alabilmek için gerekli girişi seçmelisiniz Kaynak menüsünde, “ ” veya “ ” tuşlarına basarak kaynağın ışığının yanmasını sağlayınız ve OK tuşuna basarak o moda geçiniz. “ ” veya “ ” düğmeleri ile Açık veya Kapalı ayarlarını seçebilirsiniz. Kapalı seçimi yapıldığında, uzaktan kumanda üzerindeki “SOURCE” düğmesine basıldığında bu kaynak ekran menüsünde görüntülenmez.
PC Pozisyonu Menüsü Ekranı otomatik olarak en uygun hale getirir. En uygun hale getirmek için OK tuşuna basınız. Bu özellik, görüntüyü ekranın sağ veya sol tarafına yatay olarak kaydırır. Bu özellik, görüntüyü ekranın üstüne veya altına doğru dikey olarak kaydırır. TV setine girdiğiniz çözünürlüğe ve tarama sıklığına bağlı olarak ekranda bulanık veya gürültülü bir görüntü görebilirsiniz. Böyle bir durumda, deneme yanılma yöntemiyle daha net bir görüntü almak için bu özelliği kullanabilirsiniz.
ÖNEMLİ UYARILAR 1. Üreticinin saklı bulundurduğu haklar: Üretici firma, üründe ya da ürünün kullanım kılavuzunda belirtilen özellikleri, teknolojideki ilerlemenin gereği olarak, herhangi bir bilgilendirme yapmadan değiştirme hakkını saklı tutar. 2. Ekran Teknolojisi ile İlgili Uyarılar: TFT ve Plazma teknolojisi gereği, ekranda aktif olmayan ya da sürekli parlayan beyaz, kırmızı ya da mavi noktacıklar (pixeller) bulunabilir. Bu ürünün performansını etkilemez, bu bir arıza değildir.
Contents SAFETY PRECAUTIONS....................................................................9 Specifications....................................................................................10 Supported PC Input Typical Display Modes......................................10 Step 1 - Installing the Batteries to the Remote..................................10 Step 2 - Control Touch Buttons..........................................................10 Step 3 - Connecting External Devices .....................
Specifications RF AERIAL INPUT 75 Ohm (unbalanced) OPERATING VOLTAGE 220-240V AC, 50 Hz. AUDIO OUTPUT POWER (WRMS.) (10% THD): 2 x 2,5 POWER CONSUMPTION (W): 50 W (max) < 1 W (Standby) PANEL 16:9 display, 24” Screen Size Step 1 - Installing the Batteries to the Remote 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover.
Step 4 - Connect Power and Antenna/ Cable Use 75 ohm round antenna cable. REAR OF THE TV Input Selection Once you have connected external systems to your TV, you can switch to different input sources. Press SOURCE button on your remote control consecutively for directly changing sources. Changing Channels and Volume or Make sure the power plug is plugged securely to the wall outlet. After APS is finalized, the programme table will appear on the screen.
Remote Control 17. No function 1. Standby 18. Programme up 2. Mono-Stereo / Dual I-II 3. Expand (in TXT mode) / Image size 4. Green / Picture menu 1 30 2 29 28 3 4 5 6 5. Red / Sound menu 6. Numeric buttons 7 7. Teletext / Mix SUBTITLE PIP SCREEN LANG 1 2 6 3 4 7 8 27 5 9 0 25 26 24 8 8. Cursor left 9 9. Menu on/off OK 10 10. AV / Source 11. No function 11 12 13 14 15 12. Volume Up 13. Info / Reveal (in TXT mode) 14.
HDMI True Black While watching from HDMI source,this feature will be visible in the Advanced Settings menu.You can use this feature to enhance blackness in the picture. You can set this feature as “On” for activating HDMI True Black mode Sound Menu Volume Adjusts volume level. Equalizer In equalizer menu, the preset can be changed to Music, Movie, Speech, Flat and User. Press the MENU button to return to the previous menu.
Source Menu Once you have connected optional equipment systems to your TV, you should select the required input to view pictures from that source. In source menu, highlight a source by pressing “ ” or “ ” button and switch to that mode by pressing “OK” button. With the “ ” or “ ” buttons you can set Off or On. When Off is selected; this source does not appear in the OSD when you press the “SOURCE” button of the remote control.
PC Position Menu Autoposition (in PC mode) H Position (in PC mode) V Position (in PC mode) Phase (in PC mode) Dot Clock (in PC mode) Automatically optimizes the display. Press OK to optimize. This item shifts the image horizontally to right hand side or left hand side of the screen. This item shifts the image vertically towards the top or bottom of the screen. Depending on the resolution and scan frequency that you input to the TV set, you may see a hazy or noisy picture on the screen.
IMPORTANT WARNINGS 1. Rights reserved by the manufacturer: The manufacturer reserves the right to change the features stated in the product or in the user’s manual of the product without giving any information, when required by the improvements in technology. 2. Warnings about Screen Technology: Due to TFT and Plasma technologies, there may be inactive or continuously shining white, red or blue pixels in the screen. This does not affect the performance of the product, and it is not a failure.
Üretici firma: Vestel Elektronik Sanayi ve Ticaret A.Ş.
Vestel Danışma Hattı’nı arayarak; Ürüninizle ilgili tüm soru ve taleplerinizi Vestel Danışma hattına iletebilir, şikayet, dilek, önerileriniz ve Vestel Şirketler Grubu ile ilgili sorularınızı ilgili birimlere aktarabilirsiniz. E-mail başvurularınız için; tuketicihizmetleri@vestel.com.tr Cihazınızın T.C.