Use and Care Manual

ManualsBrandsVestil ManualsBuilding materials500 lbs. 28 in. x 46 in. Linear Bench Top Tilter

0813 Rev. 5/20/2014 BTT, manual.doc

BTT-SERIES BENCHTOP TILTERS

NSTRUCTION MANUAL

Receiving instructions:

After delivery, IMMEDIATELY remove the packaging from the product in a manner that preserves the packaging and

maintains the orientation of the product in the packaging; then inspect the product closely to determine whether it

sustained damage during transport. If damage is discovered during the inspection, immediately record a

complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging.

NOTES:

1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the product

is used is exclusively the responsibility of the owner/end-user.

2) VESTIL is not liable for any injury or property damage that occurs as a consequence of failing to apply either: a)

the instructions in this manual; or b) information provided on labels affixed to the product. Neither is VESTIL

responsible for any consequential damages sustained as a result of failing to exercise sound judgment while

assembling, installing, using or maintaining this product.

Table of Contents

Hazard identification: explanation of signal words……………………………………………………………………. 2

Safety Guidelines…………………………………………………………………………..…………………….………. 2

Exploded parts diagrams and bills of materials……………………………………………………………………….. 3 – 7

Product specifications……………………………………………………………………………………………………. 8

Installation instructions…………………………………………………………………………………………………… 8

Use instructions…………………………………………………………………………………………………………… 8 – 9

Inspections & Maintenance Recommendations………………………………………………………………………. 9

Label placement diagram …………..

…………………………………………………………................................. 9

Limited warranty………………………………………………………………………………………………………….. 10

VESTIL MANUFACTURING CORP.

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703

Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868

Fax: (260) 665-1339

www.vestilmfg.com e-mail: sales@vestil.com

Summary of content (10 pages)

PAGE 1
0813 Rev. 5/20/2014 BTT, manual.doc VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.
PAGE 2
0813 Rev. 5/20/2014 BTT, manual.doc HAZARD IDENTIFICATION: explanation of signal words This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention to uses of the product likely cause property damage.
PAGE 3
0813 Rev. 5/20/2014 BTT, manual.doc FIG. 1: BTT-5-36 Exploded Parts Diagram & Bill of Materials Item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part no. 03-514-004 03-512-002 03-513-006 37024 11110 33082 03-148-001 37027 24095 68083 20-110-006 21-113-021 33084 13159 03-148-002-001 Description Frame assembly Hinge link assembly 28in. x 36in. deck subassembly 3 /8 in. - 16 Nylock nut 3 /8 in. - 16 x 1¾in. HHCS #2 zinc-plated bolt 3 /8 in. zinc-plated SAE flat washer Linear actuator (BTT-500) 7 /16 in.
PAGE 4
0813 Rev. 5/20/2014 BTT, manual.doc FIG. 2: BTT-5-46 Exploded Parts Diagram & Bill of Materials Item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part no. 03-514-004 03-513-007 03-512-002 11110 37024 33082 03-148-001 24095 68083 20-110-006 21-113-021 03-148-002-001 33084 13159 37027 Description Frame assembly 28in. x 46in. deck subassembly Hinge link assembly 3 /8 in. - 16 x 1¾in. HHCS #2 zinc-plated bolt 3 /8 in. - 16 Nylock nut 3 /8 in. zinc-plated SAE flat washer Linear actuator (BTT-500) 3 /8 in.
PAGE 5
0813 Rev. 5/20/2014 BTT, manual.doc FIG. 3: BTT-6-36 and BTT-6-46 Exploded Parts Diagram & Bills of Materials BTT-6-36 Bill of Materials: Item no. 1 2 3 4 5 Part no. 03-514-002 03-510-003 03-513-003 11105 37024 Description Base frame subassembly Cross-bar support subassembly 28in. x 36in. deck subassembly 7 /16 in. - 16 x 1in. HHCS #2 zinc-plated bolt 3 /8 in. - 16 zinc-plated Nylock nut Quantity 1 1 1 4 4 BTT-6-46 Bill of Materials: Item no. 1 2 3 4 5 Part no.
PAGE 6
0813 Rev. 5/20/2014 BTT, manual.doc FIG. 4: BTT-10-36 Exploded Parts Diagram & Bill of Materials Item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part no. 03-002-009 03-148-002 03-524-001 03-112-006 01-034-021 37024 33082 37015 24213 11109 32415 16-145-002 03-148-002-001 Description Final assembly without power Linear actuator (BTT-1000) Actuator guard assembly Cylinder pin Rubber grommet 3 /8 in. -16 Nylock nut 3 /8 in. zinc-plated SAE flat washer 10-32 zinc-plated Nylock nut #10-32 x 1in.
PAGE 7
0813 Rev. 5/20/2014 BTT, manual.doc FIG. 5: BTT-10-46 Exploded Parts Diagram & Bill of Materials Item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part no. 03-148-002 03-524-001 03-112-006 16-145-002 01-034-021 24213 37015 32415 33082 37024 11109 03-148-002-001 03-002-012 Description Linear actuator (BTT-1000) Actuator guard assembly Cylinder pin ½ in. Tinnerman fastner Rubber grommet #10-32 x 1in. flat head socket cap screw 10-32 zinc-plated Nylock nut 5 /16 in. - 18 x ½in.
PAGE 8
0813 Rev. 5/20/2014 BTT, manual.doc Product specifications Dimensions and other specifications appear in the table below: Platform dimensions Possible angles of Model Capacity (W x L x H) inclination 28in. x 36in. x 2in. 600 lb. BTT-6-36 15°; 30°; and 45° 71.1cm x 91.4cm x 5.1cm 272.7 kg 28in. x 46in. x 2in. 600 lb. BTT-6-46 15°; 30°; and 45° 71.1cm x 116.8cm x 5.1cm 272.7 kg 28in. x 36in. x 5in. 500 lb. Adjustable from 0° BTT-5-36 71.1cm x 91.4cm x 12.7cm 227.3 kg through 45° 28in. x 46in. x 5in.
PAGE 9
0813 Rev. 5/20/2014 BTT, manual.doc Power-actuated models (BTT 5-36; BTT-5-46; BTT-10-36; & BTT-10-46 The deck can be inclined at any angle from zero up to 45 degrees. To incline the deck, simply press the “UP” pushbutton on the pendant controller until the deck achieves the degree of tilt desired. To decrease the angle, press the “DOWN” button. Always return the deck to the horizontal configuration before leaving the tilter unattended.
PAGE 10
0813 Rev. 5/20/2014 BTT, manual.doc LIMITED WARRANTY Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service. Who may request service? Only a warrantee may request service.