Instructions / Assembly

Vestil Manufacturing Corporation
2999 North Wayne St., Angola, IN 46703
Ph: [phone] • Fax: [phone]
[e-mail] • www.vestil.com
CONCRETE HARDWARE KIT (standard)
The following tools/hardware are required for installing your car
stop.
CS-33-CK KIT INCLUDES:
3 - 1/2” x 6” lag bolt for each hole
3 - 1/2” washers for lag bolts
3 - 1/2” anchor sleeve for each bolt
CUSTOMER SUPPLIES:
1 - High-speed hammer drill 3/4” masonry bit
1 - Impact wrench or heavy ratchet 3/4” socket
ASPHALT HARDWARE KIT
The following tools/hardware are required for installing your car
stop.
CS-AK KIT INCLUDES:
3 - 12” long steel spikes
1 - 72” long pieces of Butyl tape
CUSTOMER SUPPLIES:
1 - Sledge Hammer
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior to
shipment. However, it is possible that the unit may incur damage
during transit. If damage is noticed when unloading, make a note
of it on the BILL OF LADING. Remove all packing and strapping
material, then inspect the unit again for damage. IF DAMAGE IS
EVIDENT, FILE A CLAIM WITH THE CARRIER IMMEDIATELY!
WARRANTY
This product is warranted for 30 DAYS from date of
purchase to be free of manufacturing defects in material and
workmanship. The manufacturer's obligation hereunder is limited
to repairing such products during the warranty period, provided
the product is sent prepaid back to the factory.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use or application contrary to installation
instructions, or disassembly, repair or alteration by any person
prior to authorization from a factory representative.
ASSEMBLY INSTRUCTIONS
CONCRETE (standard)
1.) Position the car stop in its intended position and using its
predrilled holes as templates, mark the location of each hole
on the road surface.
CAR STOP • MODEL CS-33
OWNERS
MANUAL
Revised 0809 29-126-103
A company dedicated to solving ergonomic and material
handling problems since 1955 .
Ergonomic Solutions
Assembly Instructions................................................... 1
Assembly Drawing ........................................................ 1
CAR STOP • MODEL CS-33
2.) Remove the car stop. Using high speed hammer drill
with a 3/4” masonry bit, drill a hole at each marked location
to a depth of 3-1/2” below the road surface.
3.) Insert a anchor sleeve into each hole (large sleeve opening
on top). Tap the sleeves into the holes with a hammer so that
the sleeves are set flush with the surface. Place a washer
over each sleeve hole.
4.) Make sure the substrates are thoroughly clean and dry.
Reposition the car stop in its installation position. Apply firm
hand pressure. Slip a washer onto a lag bolt, insert the
bolt through a predrilled hole in the speed bump, align over
anchor sleeve and tighten the bolt about three-quarter of the
way with the 3/4” socket. Repeat for each hole in the speed
bump. Finish tightening each bolt until just snug. DO NOT
OVER TIGHTEN! Excessive tightening may damage the
car stop and void the product warranty.
ASSEMBLY INSTRUCTIONS
ASPHALT, HIGH USE AREA’S, OR LOCATIONS WITH
TEMPERATURES OVER 110°F
1) Adhere the Butyl tape to the under structure of car stop
length wise.
2) Place car stop in desired position.
3) Insert spike through predrilled hole. DO NOT HOLD SPIKE
WHILE HAMMERING! Drive spike into ground until flush
with car stop.
Contents
Hardware Kits .............................................................. 1
Receiving Instructions ................................................. 1
Warranty ...................................................................... 1
E
N
G
L
I
S
H
E
S
P
A
N
O
L
F
R
A
N
Ç
A
I
S