Manual

ManualsBrandsVestil ManualsEquipmentFLOW Series

7 1/4"

6 3/4"

Horizontal bracing

GRAVITY FLOW RACK

STEP 1:

7 - RUBBER BASE UPRIGHT GRIP - 4PCS./UNIT

6 - NUT: M8X1.25 - 12PCS./UNIT

4 - RUBBER SPACERS - 4PCS./UNIT

FLOW-3

5 - BOLT: M8X1.25X50MM - 12PCS./UNIT

3 - ANGLE BRACING - 6PCS./UNIT

ROLLER OVERALL LENGTH - 37"

DIVIDER OVERALL LENGTH - 37"

HORIZONTAL BRACE OVERALL LENGTH - 34"

FLOW-4

ANGLE BRACE OVERALL LENGTH - 41.60"

UPRIGHT - 84"

DIVIDER OVERALL LENGTH - 49"

ROLLER OVERALL LENGTH - 49"

ANGLE OVERALL LENGTH - 52"

PARTS LIST TO ASSEMBLE UPRIGHTS:

1 - UPRIGHT - 4 PCS./UNIT

2 - HORIZONTOL BRACING - 4PCS./UNIT

UPRIGHT HEIGHT - 84"

HORIZONTOL BRACE OVERALL LENGTH - 46"

bolt

Horizontol bracing

angle bracking

angle bracing

upright

rubber spacer

nut

1 - LAYDOWN 2 UPRIGHTS ON THE FLOOR, WITH OPEN SIDES FACING EACH OTHER.

2 - WHEN ASSEMBLING BOTTOM & TOP HORIZONTOL BRACING, USE THE RUBBER SPACER

3 - CONNECT ONE END OF THE HORIZONTOL BRACING WITH 1ST UPRIGHT AND CONNECT

THE OTHER END OF HORIZONTOL BRACING AND ANGLE BRACING WITH THE 2ND UPRIGHT

4 - USE RUBBER BASE UPRIGHT GRIP ON BOTTOM OF THE UPRIGHTS.

Summary of content (8 pages)

PAGE 1
STEP 1: GRAVITY FLOW RACK 1 - LAYDOWN 2 UPRIGHTS ON THE FLOOR, WITH OPEN SIDES FACING EACH OTHER. 2 - WHEN ASSEMBLING BOTTOM & TOP HORIZONTOL BRACING, USE THE RUBBER SPACER 3 - CONNECT ONE END OF THE HORIZONTOL BRACING WITH 1ST UPRIGHT AND CONNECT THE OTHER END OF HORIZONTOL BRACING AND ANGLE BRACING WITH THE 2ND UPRIGHT 4 - USE RUBBER BASE UPRIGHT GRIP ON BOTTOM OF THE UPRIGHTS.
PAGE 2
STEP 2: 1 - Assemble 2 top beams (beam tabs should fit in upright slots). 2 - Assemble roller beams at desired height (beam tabs should fit in upright slots). 4 3 - Install safety pin in all beams ( two per beam) 1 3 2 PARTS LIST TO ASSEMBLE THE BEAMS. 1 - TOP BEAM - 2PCS./UNIT 2 - REAR ROLLER BEAM - 3PCS/UNIT FOR FLOW-3 - 4PCS/UNIT FOR FLOW-4 - 5PCS/UNIT FOR FLOW-5 3 - FRONT ROLLER BEAM - 3PCS/UNIT FOR FLOW-3 - 4PCS/UNIT FOR FLOW-4 - 5PCS/UNIT FOR FLOW-5 4 - SAFETY PIN - 2PCS/BEAM 16 PCS.
PAGE 3
STEP 3: 1 - Assemble 8 rollers per shlef. 2 - Assemble 4 dividers per shelf. PARTS LIST TO ASSEMBLE ROLLERS & DIVIDERS 1 - 8 ROLLERS PER SHELF FLOW-3-3: 24 ROLLERS FLOW-3-4: 32 ROLLERS FLOW-3-5: 40 ROLLERS 3 1 2 - 4 DIVIDERS PER SHELF (not shown in the drawing) FLOW-3-3: 12 DIVIDERS FLOW-3-4: 16 DIVIDERS FLOW-3-5: 20 DIVIDERS 3 - M6X1.00X25mm BOLT - 16PCS/SHELF FLOW-3-3: Total bolt 48 PCS. FLOW-3-4: Total bolts 64 PCS. FLOW-3-5: Total bolts 80 PCS. 4 - M6x1.00x10.
PAGE 4
STEP 4 (IF APPLICABLE) BOLT TWO UNITS TOGETHER TO MAKE A CONTINUOUS GRAVITY FLOW RACK PARTS LIST TO ASSEMBLE 2 RACKS TOGETHER 1 - THREADED STUD M8X1.25X70MM - 6PCS/UNIT 2 - NUT M8X1.
PAGE 5
GRAVITY FLOW RACK ASSEMBLY INSTRUCTIONS 9/24/2007 Fig.1 M8-1.25x50mm long Bolt (12 pcs/unit) to secure horizontal & angle bracing to to uprights Position of bottom horizontal brace (Fig.2) 7 1/4" Fig.
PAGE 6
Position of top horizontal brace (Fig.3) 6 3/4" Fig.3 Spacer 4 pcs/unit Fig.
PAGE 7
Roller bar Fig.5 M6-1.25x25mm long Bolt 16 pcs/shelf to secure 8 roller bars. M6-1.25 Wing Nut 16 pcs/shelf to secure 8 Roller bars M6-1.25 Wing Nut 8pcs/shelf to secure 4 dividers M6-1.25x10mm long Shoulder Bolt 8 pcs/shelf to secure 4 dividers Divider Fig.
PAGE 8
Bolt two units together to make a continuous Gravity Flow Rack Fig.9 M8-1.25 nut as a spacer between 2 racks, 18pcs./unit M8-1.25x70mm long stud, 6 pcs./unit Fig.