Manual

ManualsBrandsVestil ManualsEquipmentPM4-xxxx-LP

INSTRUCTION MANUAL

FOR Low Profile 4,000 lbs. Pallet Truck

ODELS NUMBER: PM4-xxxx-LP

ESTIL MANUFACTURING CORP.

2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

ELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868

AX: (260) 665-1339

URL: WWW.VESTILMFG.COM EMAIL: SALES@VESTIL.COM

Summary of content (9 pages)

PAGE 1
INSTRUCTION MANUAL FOR Low Profile 4,000 lbs. Pallet Truck MODELS NUMBER: PM4-xxxx-LP VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX: (260) 665-1339 URL: WWW.VESTILMFG.COM EMAIL: SALES@VESTIL.
PAGE 2
Hand Pallet Truck Note: Owner and operator MUST read and understand this operating instructions before use this pallet truck. Thank you for choosing our pallet truck. For your safety and correct operation, please carefully read the manual before use. NOTE: All of the information reported herein is based on data available at the time of printing. The factory reserves the right to modify its own products at any time without notice or incurring in any sanction.
PAGE 3
(D133) counter-clockwise until the forks do not lower. 3.3 If the forks do not descent when the control handle (D608 or D608S) is in the LOWER position, turn the nut (D615) or adjusting screw(D133) clockwise until raising the control handle(D608 or D608S) lowers the forks. Then check the DRIVE position according to item 3.1 and 3.2 to be sure the nut (D615) or adjusting screw (D133) is in the proper position. 3.
PAGE 4
5.6 Do not handle unstable or loosely stacked loads. 5.7 Do not overload the truck. 5.8 Always place loads centrally across the forks and not at the end of the forks (See Fig. 2). 5.9 The capacity of the truck assumes an evenly distributed load with the centre of the load being at the halfway point of the length of the forks. 5.10 Make sure that length of the forks matches the length of the pallet. 5.11 Lower the forks to lowest height when the truck is not being used. 5.
PAGE 5
HANDLE ASSEMBLY 4
PAGE 6
PARTS LIST OF HANDLE TYPE A NO. PM4-L101-H-A Description Spring PM4-L102-H-A Blade Spring PM4-L103-H-A Roller PM4-L104-H-A Elastic pin PM4-L105-H-A Elastic pin PM4-L106-H-A Elastic pin PM4-L107-H-A Elastic pin PM4-L108-H-A Control Handle PM4-L109-H-A Pull Board Qty. Remark NO.
PAGE 7
FORK FRAME ASSEMBLY PARTS LIST OF FORK FRAME No Description PM4-201SL-F Fork Frame PM4-202SL-F Bolt PM4-203SL-F-20 Rock-Arm - (TRUNION) -20" WIDE PM4-203SL-F-27 Rock-Arm - (TRUNION) - 27" WIDE PM4-203SL-F-33 Rock-Arm - (TRUNION) - 33" WIDE PM4-204SL-F Shaft PM4-205SL-F Retaining Ring PM4-206SL-F Joint PM4-207SL-F Pin PM4-208SL-F Nut PM4-209SL-F Elastic Pin PM4-210SL-F Pushing Rod PM4-211SL-F-20 Long Shaft – 20” PM4-211SL-F-27 Long Shaft – 27” Qty. 1 1 1 1 1 2 2 2 2 2 1 2 1 1 6 No Description Qty.
PAGE 8
PARTS LIST OF PUMP 7
PAGE 9
Part List of Pump NO. Description Qty. Remark NO. PM4-L301-P Retaining Ring (for axle) 2 PM4-L326-P PM4-L302-P Hub Cap 2 PM4-L327A-P PM4-L303-P Washer 2 PM4-L304-P Shaft of wheel PM4-L305-P Bearing - 6204 2RS Description Qty.