Emergency Pneumatics. Operating Instructions VETTER S.Tec Bags 10 bar Article No. 9987026702 | © Vetter GmbH I 07/14 I Changes and errors excepted.
Vetter S.Tec Bags 10 bar Contents 1. Important preliminary remarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Product description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 Description of the set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.2 Other accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.
1. Important preliminary remarks Only the knowledge and exact observance of these operating instructions guarantees correct and professional operation, produces the greatest possible use and ensures any claims made within the scope of the Vetter guarantee. The handling of the Vetter S.Tec Bag is only to be made by trained persons using the operating instructions of the manufacturer and the information from the user.
Vetter S.Tec Bags 10 bar Additional information for illuminated control element Air CU 10 bar Totmann lighting The lighting of the control element illuminates all couplings, switch levers and manometers. It is switched on and off with switch (1) on the side. 1 The control element is supplied by a 9 V block battery. Since the entire lifting bag system is designed for a temperature range of -20 °C to +55 °C, only batteries with this temperature range are allowed to be used.
2.2 Pos. Other accessories Article No. Description 1600 0261 00 Pressure regulator 200/300 bar 1 US Version 4500 psi or 1600 0262 00 (not compatible with below mentioned compressed air bottles) 2 1600 0108 00 Comp. air bottle 6 l / 300 bar 3 1600 0199 00 Comp.
Vetter S.Tec Bags 10 bar 2.3 Vetter safety coupling system a. Input coupling of the controller 3 2 1 Connect the air supply hose or the connection hose of the pressure regulator to the nipple of the input coupling (1) on the controller pushing the nipple solidly into the coupling until the ratchet action can be felt. In order to ensure that it is correctly connected: turn the brass sleeve (2) of the coupling opposite to the safety pin (3). b.
Temperature resistance of S.Tec Bags: Cold resistance -40° C Cold flexible -20° C Heat resistance long-term +90° C Heat resistance short-term +115° C The aramide layer on the S.Tec Bag can be damaged by damage made to the bag surface, e.g. cuts, cracks, punctures or by the effects of ozone.
Vetter S.Tec Bags 10 bar In case the lifting height of an S.Tec Bag is not sufficient then a maximum of 2 bags can be placed over each other. In this mode, the lifting height is additive for both S.Tec Bags. However the lifting power only corresponds to that of the smaller bag. Basically, the lower bag should always be inflated first. Sequence: large bag below, small bag on top! Never place 3 or more bags over each other! An S.
Never position 3 or more bags on top of each other! Ensure load against slippage. In order to fully use the strengths of the S.Tec Bag, the distance between load and bag should be at a minimum. The foundation support must brace at least the complete area of the bag and the smallest edge length of the foundation support must be larger than the height of the foundation support.
Vetter S.Tec Bags 10 bar 3. Preparing the product for use 3.1 Preparations for operation Remove the S.Tec Bag from the vehicle. Prepare the inflation device. Ensure that sufficient air supply is available. Only perfectly working and tested S.Tec Bag systems are to be used! From case to case, the head of operations is to decide, within his area of responsibility, about the method to be used for the operation as well as the operating instructions of the user. 3.
4.2 Operation with other sources of compressed air Basically, every source of air available can be used for operation of the S.Tec Bag as long as the pressure does not exceed 12 bar and that the air is free of oil as far as possible. Amongst others, the set of transition pieces (Art. No.: 1600 0125 01) with the following adapters are available for operation with other air sources: 8 5 9 3 4 6 7 2 10 1 1. Truck compressed air connection, dual brake system.
Vetter S.Tec Bags 10 bar 4.3 Dismantling of the lifting bag system after use Dismantling of the lifting bag system is carried out after ensuring the lifted load and complete deflation of the lifting bag system, including dismantling of all accessory parts in the reverse order. 4.4 Limit for the period of use S.Tec Bags are subject to natural aging the same as any other rubber products.
5. Elimination of defects If the safety valve blows too early because of foreign body penetration caught up inside then the blow-off valve is to be fully opened on the head of safety valve by turning counter-clockwise so that the compressed air can escape. If, due to this, the foreign body is not removed then the upper part of the safety valve is to be unscrewed when the safety valve is disassembled. To do this, position the pipe wrench in the centre and unscrew by turning to the left.
Vetter S.Tec Bags 10 bar 7. Technical data S.Tec Bags 10 bar Unit Art. No. Lift power Lift height Insertion height Dimensions Operating max. pressure Test pressure Air requirement at 10 bar/145 psi Nominal capacity Weight ca. Lift height Insertion height Dimensions Operating max. pressure Test pressure Air requirement at 10 bar/145 psi Nominal capacity Weight ca. V 4 S.Tec V 6 S.Tec V 7 S.Tec 1315000100 1315000200 1315000300 1315000400 1.1 3.8 6,3 7 US tons 1.3 4.2 6,9 7,7 cm 7.
S.Tec Bags 10 bar Unit Art. No. Lift power Lift height Insertion height Dimensions Operating max. pressure Test pressure 1315000900 1315001000 1315001100 1315001200 28.9 27.7 40.9 44.8 US tons 31.9 30.5 45.1 49.4 cm 30.6 20.1 37 31 inch 12 7.9 14.6 12.2 cm 2.5 2.5 2.5 2.5 inch 1 1 1 1 cm 52 x 62 31 x 102 65 x 69 43 x 115 inch 20 x 24 12 x 40 26 x 27 17 x 45 bar 10 10 10 10 psi 145 145 145 145 bar 16 16 16 16 psi 232 232 232 232 361.9 258.5 632.
Vetter S.Tec Bags 10 bar 8. Page 15/18 Diagram: Force vs. Stroke V 1 - V 85 S.
9. Safety of machines - DIN EN ISO 12100-1 and 12100-2 Page ref. DIN EN ISO 12100-1 4.2 Mechanical dangers 4.4 Thermal dangers 4.5 Danger due to noise 4/6/ 8 5/6 3/5/6 DIN EN ISO 12100-2 4.6 Measures for stability 4 4.8 Observing basic ergonomical principles 7 / 9 / 10 4.10 Avoiding dangers caused by pneumatic and hydraulic equipment 9 / 10 / 11 4.11 Using measures for inherent safety of control constructions 4.12 Minimizing the failure of safety functions 5.
Vetter S.Tec Bags 10 bar EC Conformity Declaration (available on request) in accordance with Directive 2006/42/EC Manufacturer name and address: Vetter GmbH A Unit of IDEX Corporation Blatzheimer Str. 10 - 12 53909 Zülpich We hereby declare, that the VETTER S.Tec Bags 10 bar for lifting and lowering of loads Type: Serial-No.
Place your trust in emergency pneumatics! We are the company who can help you, find a solution to your problem! Vetter GmbH A Unit of IDEX Corporation Sales Blatzheimer Str. 10 - 12 D-53909 Zülpich Germany Tel.: +49 (0) 22 52 / 30 08-0 Fax: +49 (0) 22 52 / 30 08-590 Mail: vetter.rescue@idexcorp.com www.vetter.de Article No. 9987026702 | © Vetter GmbH I 07/14 I Changes and errors excepted.
