Technical Support and E-Warranty Certificate www.vevor.com/support ICE CREAM MACHINE MODEL:BQL-9200STA BQL-9200ST We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.
ICE CREAM MACHINE MODEL:BQL-9200STA BQL-9200ST BQL-9200STA BQL-9200ST NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate www.vevor.com/support This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received.
Warning-To reduce the risk of injury, user must read instructions manual carefully. CORRECT DISPOSAL This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol.
VII.Ice Cream Machine Cleaning and Maintenance Methods VIII.Fault Analysis and Solutions Safety Precautions ·Before using the appliance, please read this user manual to ensure that you gain the maximum benefit from it. 1. WARNING: 1.
flammable propellant in this appliance. 11. Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances. ·Note: This appliance contains flammable refrigerant R290 and foaming agent cyclopentane. Please avoid contact fire when you transport and use it. Please ask professional for servicing when the machine broke down. Please send it to your local appointed disposal station when you discard it.
This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
to allow cold air to enter the machine and allow hot air to escape, to ensure the condensation cycle of the machine.Clean the dust on the condenser regularly . Note: The machine will inevitably be shaken during transportation. It is best to use it for 4 hours after smoothing. III.Electrical Connection 1) According to the required power, determine the wire size used in the connection circuit. All internal lines in the ice cream machines have been connected before leaving the factory.
Product Structure： 1.screw for distributor 2.pin 3.handle 4.piston 5.wave ring 6.beater 7.seal for distributor 8.tray 9.compressor 10.condenser 11.fan 12.gear motor 13.mother board 14.panel 15.hopper 16.cover for hopper 17.rear plate 18.
Introduction Home Page (A) Setting Page (B) Switch on the power, as shown in figure (A), bottom-left corner shows the tank is short of ingredient, the red icon flashes. After adding ingredient, red icon changes to white icon.and press “Set” enter to figure ( B)“Setting page” . Home Page (C) Home Page (D) Press “ Sales settings” : Password: 8888; Press “Clear” Counting restart, press “back” “Back” Go back to home page.
Cleaning Page (E) Cooling Page (F) In the standby state, press “Wash” enter to figure (E) “Cleaning Page” .the stirring motor runs, display screen shows the current value of the current stirring motor. Press “ Stop” to enter the standby state. In the standby state, press “Auto” enter to figure (F) “cooling Page”, the stirring motor, the compressor, and the fan motor start, and the display screen shows the current value of the current stirring motor. Press “Stop” to enter the standby state.
Display screen show as figure (H), please cut off the power switch to wait or check. BQL-9200STA Operation Panel and Function Introduction the operation panel is divided into LCD screen (select the corresponding operation with the object control) LCD screen operation and function introduction ) 1.the washing-defrosting key: in the standby state, tap this key, enter the cleaning state, the cleaning indicator light is on, the buzzer makes a short sound, and the stirring motor operates.
4.preservation pre cooling key : In standby state, press the “Preservation” button, the preservation indicator lights up, the buzzer makes a short sound, the agitator motor, compressor, fan motor delay start, the liquid crystal display shows the current value of the current agitator motor. 5.Press the button and enter standby.
Please use the food detergent and cleaning brush to clean the parts that have been dismantled (refer to the product structure drawing), especially the groove of the O-ring should be thoroughly cleaned. Note: Please do not damage or lose parts during operation; do not use hot water or dish washing detergent to clean the resin parts, otherwise it may cause deformation; please do not soak the parts in the detergent for more than 30 minutes, otherwise it may cause deterioration.
3）Assembly of the discharge valve, refer to (Figure K) Note: Don't forget to install the seal ring 4）Install the water tank as shown (Figure L). Figure K Figure L Note: the components are assembled in the process of the ice cream machine, make sure the control power switch is off.
hardness value. 4 ） Press the "Auto" button, the machine enters the cooling state. press the “Fresh” button to cool the slurry in the feed chute. 5)When the hardness of the current ice cream reaches the set hardness, the machine will automatically stop and rest; when the machine stops taking a rest, the automatic start time adjustment range is within 3-9 minutes. At this time, press “ Set”→“User setting”→”Automatic restart time to set the machine to enter the next refrigeration.
1）Press the wash button to discharge all the slurry in the tank, press stop, the machine stops. 2）Please use hot water and an appropriate amount of disinfectant, pour it into the tank and pour it into a volume of about 70% of the tank. 3）Press the wash button again and stir for about 5 minutes before draining the cleaning solution. 4）Please wash with hot water for 2-3 times and stop. 5）Use a cleaning brush to clean the chute discharge port.
3）Press the wash button again and stir for about 5 minutes before draining the cleaning solution. 4）Please wash with hot water for 2-3 times and stop. 5）Use a cleaning brush to clean the chute discharge port.Carefully clean the liquid level sensor with a clean cloth and a cleaning brush.If the cleaning is not clean, sometimes the material shortage alarm will not work. Please remove the mixing blade and clean the rotating shaft and the head with a clean cloth.
IV.Cleaning and maintenance of the condenser During the working period, the condenser will be covered with dust ,which will affect the heat dissipation. The cooling effect is poor. It must be cleaned every two months. It is best to clean it by professional. Always turn off the power before cleaning, and do not damage the condenser fins. Fault Analysis and Solutions No. 1 2 Fault phenomenon The machine does not start. Cleaning function does not work Cause Method of exclusion 1.
3 The compressor docs not run 1.Low voltage 1.Check the supply voltage 2.Function switch wiring loose 2.Function switch cable reconnection 3.Contactor is bad 3.Replace contactor 4.There is a problem with the PCB 4.Replace the PCB board 5.Capacitor failure (220V series) 5.Replace capacitor 6.Compressor is bad 6.Replace compressor 1.Refrigerant leak 4 5 Not cooling 2.Condenser blocked 1.Repair the leak point and vacuum the refrigerant 2.Cleaning the condenser 3.The fan does not tum 3.
6.motor speed is not match 1.Slurry ratio is wrong 6 7 8 Ice cream is too soft Ice cream is too hard Material Leakage 6. press "set", “factory settings"enter password 6800 1o retest 1.Reconstitute qualified slurry 2.Improper hardness setting 2.Reset hardness 3.Motor current is large, there is a short circuit. 3.Repair or replace the motor 4.Improper hardness setting 4.Reset hardness l.Too much water in the ingredients 1.Reconstitute qualified slurry 2.Improper hardness setting 2.
9 10 The compressor stops after the ice cream is formed, and the motor does not stop. When the ice cream is made, the motor does not turn, and the ice cream does not come out 11 Beater split 12 LCD does not display 1.Travel switch contacts are attached. 1.Repair or replace the travel switch 1.Travel switch damage 1.Repair or replace the travel switch Under normal circumstances, it will not happen. The abnormal situation is as follows. 1.Slurry water, freezing tank 2.
5.Excessive use of a cylinder when playing ice cream 6.Hot slurry is poured into the cylinder for rapid cooling 7.When the motor direction is reversed, the material is cooled. 8.There is a problem with the PCB 9.LCD monitor is damaged UH--Over voltage alarm 13 Alarm display UL-Low voltage alarm IJ -- Motor overload alarm - 21 - 2.
Made In China - 22 -
Technical Support and E-Warranty Certificate www.vevor.
