LEAD 20 20W Tube-Driven Amplifier User Manual VC-20
Table of Contents Table of Contents............................................3 Product Safety Information............................4 Panel Functions...............................................5 Technical Specifications.................................
Product Safety Information WARNING! Please read ALL Safety & Operating Instruction BEFORE using this product. CAUTION: To avoid the risk of fire or electric shock, please do not expose this product to rain or moisture. Dangerous high voltages are present inside the enclosure. Do not open the cabinet or remove either the front or the back cover. Refer servicing to qualified personnel only. Power Sources This product should be operated only from the type of power source indicated on the marking label.
Panel Functions (Please refer to Fig. 1 and Fig. 2 for details.) A. THE FRONT PANEL ON ON STANDBY POWER 12 13 CH SELECT 0 INPUT 1 10 0 CLEAN VOLUME 2 10 OVERDRIVE GAIN 3 4 0 10 -15 +15 -15 +15 OVERDRIVE LEVEL BASS MID 5 6 7 -15 +15 TREBLE 8 0 10 0 10 REVERB MASTER VOLUME 9 10 11 Fig. 1: The Front Panel 1. Input: Used to connect the signal output from an electric guitar. (Use a shielded cable with 1/4” mono plug.) 2.
5. Overdrive Level: Adjusts the volume level of Overdrive Channel. 6. Bass: Adjusts the low frequency level. Turn this knob clockwise to boost the bass sound, counter clockwise to cut the bass sound accordingly. Center position (straight up) provides no cut or boost. 7. Mid: Adjusts the middle frequency level. Turn this knob clockwise to boost the middle sound, counter clockwise to cut the middle sound accordingly. Center position (straight up) provides no cut or boost. 8.
B. THE REAR PANEL CAUTION HT FUSE T1AL250V Input Power 100W Voltage 100V~ 50 60Hz 120V~60Hz 230V~50Hz 240V~50Hz RISK OF ELECTRIC SHOCK, DO NOT OPEN! CHASSIS SURFACE HOT! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. INDOOR USE ONLY! AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION: SUPERFICIE DE CHASSIS CHAUDE SERIAL NUMBER Fuse Rating T2AH250V T2AH250V T1.6AH250V T1.
17: FX Send: This jack is used to send signal from the amp to external effects or signal processing devices. 18. Serial/Parellel FX: Allows you to select the desired type of effects loop, parallel or serial. 19. FX Return: This jack is used to receive signal from an external effects or signal processing devices. 20: Speaker Output (8 ohm): Used to connect an external speaker from the amplifier’s output (min 8 Ω), this switches out internal speakers.
Technical Specifications Name/Model VHT 20W Tube-Driven Amplifier / LEAD 20 Power Requirements & Consumption 120VAC, 60Hz ; 100/115VAC, 50/60Hz ; 220VAC/230VAC/240VAC, 50/60Hz Total Output Power 20W RMS Amp Type Tube Amp Power-Amp Section (2) EL84 Tubes Pre-Amp Section (4) 12AX7 Tubes Speaker 1 x 12” Celestion G12 H30 (16 ohms) Controls Clean Volume, Overdrive Gain, Overdrive Level, Reverb, Master Volume EQ 3-Band - Treble, Mid, Bass Reverb Accutronics/Reverb
Notes 10
Notes 11
Limited Warranty Information This amplifier is warranted, to the original Purchaser, to be free from defects in material and workmanship for a period of one (1) year, excluding the Tubes, which are warranted for ninety (90) days, from the original date of purchase. The manufacturer shall, at its option, either repair or replace the defective product if the product is returned to the original place of purchase.