Quick Guide XX268-30-01 CE102B Network Outdoor Bullet Camera Vicon Industries Inc. Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation.
Quick Installation Guide 1. Description The information in this manual provides quick installation and setup procedures for the CE102B-NIR Bullet Camera. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-date manual, www.vicon-security.com.
Quick Installation Guide 2. Installation 2.1 Camera Installation Base Installation 1. Create a hole in the mounting surface for the cables. Route the necessary cables to the mounting location. 2. Secure the camera mounting base to the wall or ceiling using the screws supplied in the accessory kit. Note: Make sure the mounting surface is strong enough to support the weight of the unit.
Quick Installation Guide Camera Dimension See the diagrams below for the exact dimension Dimensions Unit: mm 2.
Quick Installation Guide • Connecting to the RJ-45 Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is used for directly connection to PC, while a direct cable is used for connection to a hub or switch. Micro SD memory slot Remove the front cap of the camera to insert the SD memory card (customer-supplied). SD memory card slot Remove the front cap • Connecting the Power Connect the 12 VDC power adaptor (customer-supplied) to the camera.
Quick Installation Guide 2.2 Network Connection and IP assignment The network camera is designed for use on an Ethernet network and requires an IP address for access. Most networks today have a DHCP server that automatically assigns IP addresses to connected devices. By the factory default, your camera is set to obtain the IP address automatically via DHCP server. If your network does not have a DHCP server the network camera will use 192.168.1.100 as the default IP address.
Quick Installation Guide 3. Operation The network camera can be used with Windows® operating system and browsers. The recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows. Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX controls. Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but the functionality is the same or similar. 3.1 Access from a browser 1. 2. 3.
Quick Installation Guide 3.2. Access from the internet Access from the internet once connected, the Network Camera is accessible on your local network (LAN). To access the network camera from the Internet you must configure your broadband router to allow incoming data traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the network camera. This is enabled from Setup > System > Network > NAT.
Quick Installation Guide The protocol drop-down list allows you to select which combination of protocols and methods to use depends for your viewing requirements and on the properties of your network. 2) Control toolbar The live viewer toolbar is available in the web browser page only. It displays the following buttons: The Stop button stops the video stream being played. Pressing the key again toggles the start and stop. The Start button connects to the network camera or start playing a video stream.
Quick Installation Guide 3.5 Network Camera Setup This section describes how to configure the network camera, and is intended for product Administrators, who have unrestricted access to all the Setup tools; and Operators, who have access to the settings for Basic, Live View, Video & Image, Event, and System Configuration. You can configure the network camera by clicking Setup in the top right-hand corner of the Live View page.
Quick Installation Guide 1. 2. 3. 4. 5. 6. 7. Switch off the network camera by disconnecting the power adapter. Remove the front cap of the camera. Press and hold the Reset button while reconnecting the power. Keep the Reset button pressed for at least 2 seconds. Release the Reset button. The network camera resets to factory defaults and restarts after completing the factory reset. Close the front cap of the camera. Caution: When performing a Factory Reset, you will lose any settings you have saved. 3.
Vicon Industries Inc. Internet Address: www.vicon-security.