Product specifications

ManualsBrandsVicon ManualsDigital CameraIX 3000 L

Installation&

eration Manual

IX 1000 L, IX 1000 H

IX 3000 L, IX 3000 H

Colour Camera

Vicon Industries Inc. Does not warrant that the functions contained in this equipment will meet your requirments or

that the operation will be entirely error free or perform precisely as discribed in the documentation. This system

has not been designed to be used in life critical situations and must not be used for this purpose.

Product specifications subject to change without notice.

Vicon and ist logo are registered trademarks of Vicon Industries Inc.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24- Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 WEB: vicon-cctv.com

Summary of content (16 pages)

PAGE 1
Vicon Industries Inc. Does not warrant that the functions contained in this equipment will meet your requirments or that the operation will be entirely error free or perform precisely as discribed in the documentation. This system has not been designed to be used in life critical situations and must not be used for this purpose. Copyright © 2006 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice.
PAGE 2
Dear Customer! By selecting this VICON product you have chosen a professional device which guarantees highest possible quality and reliability. We like to thank you very much for your confidence in our products and kindly ask you to read the following instructions carefully before commissioning the product in order to be able to take full advantage of all quality features regarding this product line.
PAGE 3
GENERAL INFORMATION General Information Safety Precautions * Read these instructions carefully before commissioning the camera in order to avoid damages caused by improper installation or use. * Installation may only be carried out by authorised personnel according to the local safety regulations. * Operate the camera with the designated voltage only. * Follow the safety instructions attached to the camera. * Never use the camera for other purposes than designated.
PAGE 4
MOUNTING THE CAMERA Mounting the Camera Mounting the Camera to a Wall Mount -4-
PAGE 5
COMMISSIONING THE CAMERA Commissioning the Camera Tips for Camera Location 1.0 To avoid internal overheating: - never expose the camera to direct sunlight without additional camera housing - keep sufficient distance to direct heat sources. 2.0 Never install the camera at humid, oily or dusty locations without using an additional housing. (without additional housing the camera is not suitable for outdoor use!) 3.0 The camera should be installed out of reach (min. height: 2.30 m) 4.
PAGE 6
COMMISSIONING THE CAMERA Adjustment of Back Focus This adjustment should only be carried out, if the lens cannot be focused properly using the lens focus ring. For such a case proceed as follows: 1 Loosen the Allan head screw with the attached Allan head key. For large distances, turn the focus ring of the lens almost (0.5 cm) to the "endless" limit position. If you need to focus an object near the camera, turn the focus ring of the lens to a position 1cm before the "near" limit position.
PAGE 7
COMMISSIONING THE CAMERA Focusing the Camera Lens After you have selected the correct picture detail you have to adjust the lens focus. The focus adjustment needs to be done with the iris fully open, since the camera has the smallest depth of focus in this position. If the focus adjustment was not done with the iris completely open, the picture would be sharp during the day but slowly getting out of focus the more the light disappears.
PAGE 8
CIRCUIT POINTS AND OPERATION Circuit points and operation Rear view 12V DC / 24V AC Model Video, ELC, DC: Change-over between video drive lenses (Video), Auto Shutter (ELC) and DC drive lenses (DC) ELC ON OFF ON VIDEO DC DC LEVEL: Shutter adjustment during DC lense operation DC LEVEL FL AGC BLC OFF ON OFF AC24V/ DC12V FG PL: Power signal FL: Flickerless on / off VIDEO OUT AGC: Automatic gain on / off BLC: Back Light Control on / off Rear view 230 V AC Model AC24V / DC 12V: Power connection, the
PAGE 9
CIRCUIT POINTS AND OPERATION Lense mounting and connection ES-Control DC-Control 1. +8,5 V DC 2. NC 3. ES-Signal 4. Ground (GND) 1. 2. 3. 4.
PAGE 10
EXHIBIT Exhibit Troubleshooting Error Cause No picture - No operating voltage (check red LED) Coaxial connection interrupted (check video cable) The picture is noisy - Insufficient light The lens drive of the used lens (DC / AI) is not properly adjusted to the camera (level too low) The picture is too bright - The lens drive of the used lens (DC / AI) is not properly adjusted to the camera (level too high) Too much peak light; change camera location or activate backlight function of the camera -
PAGE 11
EXHIBIT Technical Specifications Model IXion 1000 IXion 3000 1/3“ Super HAD CCD SENSOR 440.000 Effective Pixels Resolution Sensitivity 550 TVL Colour 0,45 1/50 ~ 1/100.000 (PAL) Auto Shutter > 48 dB (AGC OFF) Signal to Noise Ratio (SNR) ON/OFF (28dB) AGC / ALC 12V DC Intern / 24V AC & 230V AC Linelock ON / OFF Backlight compensation AWB White Balance Day / Night Function 550 TVL Colour/ 570 TVL B/W 0,3 Lux (F1.4, 30IRE, AGC ON) 0,1Lux (F1.
PAGE 12
CLEANING AND CARE Cleaning and Care Before you start to clean the camera body, disconnect the unit from power supply. For reasons of electrical safety never clean the camera with water or other liquid matters and never put the camera under water. To clean use a soft dry cloth. Cleaning the camera inside is strictly forbidden and may only be done by your authorised dealer.
PAGE 13
NOTES -13-
PAGE 14
NOTES -14-
PAGE 15
SHIPPING INSTRUCTIONS Shipping Instructions: Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. Vicon Industries Inc.
PAGE 16
Vicon Industries Inc.