Quick Guide XX258-20-06 Roughneck® V920D Series Camera Domes Vicon Industries Inc. Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation.
V920D Series Quick Installation Guide 1. Description The information in this manual provides quick installation and setup procedures for the Roughneck® V920D Series of Camera Domes. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-date manual, www.vicon-security.com.
V920D Series Quick Installation Guide • Package Component The system comes with the following components: Camera unit Installation CD Installation Guide Template Sheet Accessory Kit Optional OSD Controller Check your package to make sure that you received the complete system, including all components shown above. Note: The optional V920D-OSD OSD Controller and V920D-AUDIO audio cable assembly can be purchased separately. • Contents in the installation CD 1. The V920D User’s Manual 2.
V920D Series Quick Installation Guide Quick Installation For complete detailed instructions on how to install the V920D, read the Installation section.
V920D Series Quick Installation Guide 2. Installation The V920D mounts directly to a ceiling or wall using four mounting holes. As a mounting alternative, the mounting holes align with a standard 4 x 4 electrical box (use V910/V600W-PLATE adapter plate for a clean appearance). There is an accessory kit included with the Roughneck V920D. The table below lists the contents.
V920D Series Quick Installation Guide 2.1 Connection For the operation of the network camera, it is necessary to connect a network cable for data transmission (IP version) and power connection from customer-supplied power adapter. Depending on operation methods, it is possible to additionally connect an alarm cable. Refer to the full User's manual.
V920D Series Quick Installation Guide External devices can be used to signal the network camera to react on events. Mechanical or electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors. G (Ground): Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector. Alarm Out: The network camera can activate external devices such as buzzers or lights. Connect the device to the AO (Alarm Out) and G (Ground) connectors.
V920D Series Quick Installation Guide ▶ ID & IP assignment To make changes in the OSD menu, use the OSD controller (provided optionally). You can set Camera Title and IP Address. 1. 2. 3. 4. Connect the OSD Controller to the Service Monitor port of the network camera. Connect Service Monitor and the Video Output port of the OSD Controller. Press the SET key to access Main menu. Change Camera ID, and IP Address. You can change the Name or Title and IP address of the camera.
V920D Series Quick Installation Guide If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to search and allocate an IP address to your products, or reset the product to the factory default settings and then perform the installation again. 1. 2. Connect the network camera/device to the network and power up.
V920D Series Quick Installation Guide 3. Operation The network camera can be used with Windows operating system and browsers. The recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows. Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but the functionality is the same or similar. 3.1 Access from a browser 1. 2. 3. Start a browser (i.e., Internet Explorer).
V920D Series Quick Installation Guide 3.3 Setting the admin password over a secure connection To gain access to the camera, the password for the default administrator user must be set. This is done in the “Admin Password” dialog, which is displayed when the network camera is accessed for the setup at the first time. Enter your admin name and password, set by the administrator. Note: The default administrator username is “ADMIN” and password is “1234”.
V920D Series Quick Installation Guide The Snapshot button takes a snapshot of the current image. The location where the image is saved can be specified. The Digital Zoom activates a zoom-in or zoom-out function for the video image on the live screen. The Full Screen button causes the video image to fill the entire screen area. No other windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full screen view.
V920D Series Quick Installation Guide • Adjusting Zoom: Click“<” button to zoom out and click “>” button to zoom in. The focus is moved slightly after adjusting zoom; adjust the focus again, as necessary. • Adjusting Focus: Click “>” button for far focus and click “<” button to near focus. • Fine Focus: Click “Go” button to readjust focus automatically. Note: Click the button in the Live View screen to set the focus to the optimum position. 3.
V920D Series Quick Installation Guide 3.6 Resetting to the factory default settings To reset the network camera to the original factory settings, go to the Setup>System> Maintenance web page (described in “3.5.5 System > Maintenance”) or use the Reset button (SW1) on the board of the dome camera, as described below: • Using the Reset Button Follow the instructions below to reset the Network Camera to the factory default settings using the Reset button. 1. 2. 3. 4. 5. 6. 7.
Vicon Industries Inc. For office locations, visit the website: www.vicon-security.