Quick Guide XX247-30-01 V-CELL-HD High-Security Corner-Mount Cameras Vicon Industries Inc. Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation.
V-CELL-HD Quick Installation Guide 1. Description The information in this manual provides quick installation and setup procedures for the V-CELL-HD of High-Security Corner-Mounted Cameras. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly before beginning an installation. Refer to the complete manual for detailed information.
V-CELL-HD Quick Installation Guide 2. Installation For the network camera to operate, it is necessary to connect a network cable for data transmission and power connection from customer-supplied power supply. 2.1 Exploded View Parts and Description ① ② ③ ④ ⑤ Main Power 24VAC/12VDC (↑(+) pole /↓(-) pole) RJ45(PoE) Port Micro-SD Card Slot Alarm & Audio In/Out Port Status LED Upon boot-up, green and red are both on for a short time and then only green will be on.
V-CELL-HD Quick Installation Guide Quick Installation (without 1. 2. 3. 4. 5. 6. Rear Cover) Use camera mounting frame as template to mark mounting holes on mounting surface. (Fig.1) Drill holes for mounting base and a minimum 3/4 in. hole for routing wines. (Fig.1) Mount camera mounting frame using appropriate hardware for mounting surface. (Fig.2) Route wires through hole in wall and out through base plate. (Fig.2). Terminate wires to camera board. Mount front plate to base plate. (Fig.
V-CELL-HD Quick Installation Guide Quick Installation (using Rear Cover) 1. Use rear cover as template to mark mounting and cable access holes. 2. Drill mounting and cable access holes in mounting surface. 3. Insert cable clamp into access hole, route cables through clamp and mount cover using appropriate hardware. 4. Use camera mounting frame to mark its mounting holes, drill holes and mount using appropriate hardware. 5. Terminate wires to camera board.
V-CELL-HD Quick Installation Guide 2.2 Connections • Connecting to the RJ-45 Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is used for directly connection to PC, while a direct cable is used for connection to a hub. Micro SD memory slot on the board Insert the SD memory card (customer-supplied). • Connecting Alarms Alarm-In: External devices can be used to signal the network camera to react upon events.
V-CELL-HD Quick Installation Guide The Video Output can also be used for easy zoom and focus control when adjusting the lens. Video Output is restricted to 704x480 (576) resolution. Note: The optional OSD Controller can be purchased separately. 2.3 Network Connection and IP assignment The network camera is designed for use on an Ethernet network and requires an IP address for access. Most networks today have a DHCP server that automatically assigns IP addresses to connected devices.
V-CELL-HD Quick Installation Guide Note: For more information, refer to the Smart Manger User’s Manual. 3. Operation The network camera can be used with Windows® operating system and browsers. The recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows. Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX controls. Note: Some screens may appear different (i.e.
V-CELL-HD Quick Installation Guide 3.2. Access from the internet Once connected, the network camera is accessible on your local network (LAN). To access the network camera from the Internet you must configure your broadband router to allow incoming data traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the network camera. This is enabled from Setup > System > Network > NAT. For more information, see “3.5.
V-CELL-HD Quick Installation Guide 3.4 Live View Page The Live View page provides seven screen modes: 1920x1080, 1280x1024, 1280x720, 704x480 (576), 640x480, 352x240 (288), and 320x240. Select the most suitable mode in accordance with your PC specifications and monitoring purposes. 1) General controls Live View Page Search & Playback Page Setup Page Help Page The video drop-down list allows you to select a customized or pre-programmed video stream on the live view page.
V-CELL-HD Quick Installation Guide Use this scale to control the volume of the speakers. Use this scale to control the volume of the microphone. 3) Video Streams The network camera provides several images and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in network camera provides access to H.264, MPEG-4 and Motion JPEG video streams, and to the list of available video streams.
Vicon Industries Inc. Internet Address: www.vicon-security.