Manual

ManualsBrandsViconics ManualsFor HomeS80

S60 DUCT SENSOR

ADAPTER FOR

THERMOSTAT

This sensor can be mounted

directly onto the back of any

MICRO-STAT, with the

supplied hardware. This

transforms the MICRO-STAT

into a duct-mounted stat.

S70: REMOTE DUCT

SENSOR

This sensor can be mounted

directly onto the supply or return

of the ventilation duct. The

MICRO-STAT may be located

on the wall with temperature

sensing from the remote S70

sensor location.

S80: ROOM SENSOR

This sensor can be wall in any

remote location. The MICRO-

STAT may be located on the

duct or other location, with

temperature sensing from the

S80 sensor location.

S90: IMMERSION

SENSOR

This sensor is intended for

temperature control for hot or

cold water, or other fluids. The

sensor features 316 Stainless

teel construction with 1/4"

diameter.

APPLICATIONS

• Remote control of temperature from air return.

• Remote control supply temperature.

• Limitation of supply temperature.

• Auto changeover of damper operation from supply

temperature monitoring.

• Hot water control.

TEMPERATURE SENSORS ARE COMPATIBLE

WITH ALL VICONICS MICRO-STAT SERIES

ELECTRONIC THERMOSTATS.

• WALL

• DUCT

• IMMERSION

The model S60, S70, S80, S90 are part of Viconics' Micro-

Stat Series low voltage RHVAC room temperature and

humidity controls line.

SPECIFICATIONS

Operating Conditions: -18 °C to 82 °C ( 0 °F to 180 °F )

0% to 95% R.H. non-condensing

Sensor: 47 K NTC thermistor

Interchangeability: ± 1 °C @ 25 °C ( ± 1.8 °F @ 77 °F )

Accuracy: ± 2 °C ( for -18 °C to 82 °C )

± 3.6 °F ( for 0 °F to 180 °F )

WIRING

These sensors may be wired using standard copper wiring 12 to

24 Ga. without regard to sensor polarity. Remove the internal

"J4" thermostat jumper. By removing this internal jumper, one of

these sensors may be used instead of the temperature sensor in

the MICRO-STAT.

Wire lengths may exceed 100 feet without causing temperature

errors, due to the high 47,000 ohm resistance.

Avoid running long sensor leads closed to, or in the same conduit

as, high voltage and power wiring.

Four sensors may be wired in series / parallel combination in

order to obtain average temperature readings.

ORDER CODE

S60 - 47K

DUCT SENSOR ADAPTER FOR

THERMOSTAT

S70 - 47K

REMOTE DUCT SENSOR

S80 - 47K

ROOM SENSOR

S90 - 47K

IMMERSION SENSOR

Example: S80 - 47K

CRO-ST∆T



SENSORS

S60, S70

S80, S90

Summary of content (2 pages)

PAGE 1
µiCRO-ST∆T SENSORS  S60 DUCT SENSOR ADAPTER FOR THERMOSTAT This sensor can be mounted directly onto the back of any MICRO-STAT, with the supplied hardware. This transforms the MICRO-STAT into a duct-mounted stat. S70: REMOTE DUCT SENSOR This sensor can be mounted directly onto the supply or return of the ventilation duct. The MICRO-STAT may be located on the wall with temperature sensing from the remote S70 sensor location.
PAGE 2
APPLICATIONS DIMENSIONS S60 MICRO-STAT 0.5" ( 12.7 mm ) 3.77" ( 95.8 mm ) 20 25 2 15 30 10 S90 C PIPE 0.9" ( 22.8 mm ) 1.6" ( 40.6 mm ) LIQUID 1/4" BORE-THRU COMPRESSION FITTING OR WELL MICRO-STAT S70 1.275" MOUNTING HARDWARE 3.77" ( 95.8 mm ) S60 0.9" ( 22.8 mm ) 2.8" ( 71 mm ) S70 VENTILATION DUCT WIDTH: 4.5" ( 114 mm ) MICRO-STAT 20 25 15 30 2 10 S80 C WIRING FROM TOP OR FROM BACK SECURITY SCREW 1 2 3 4 5 ROOM MICRO-STAT 6 7 8 9 10 S80 20 25 15 30 BASE 2 10 3.