Installation Manual 1 1x1
Material Needed Included Ceiling | 1 uni. Lateral | 3 uni. Door | 1 uni. Structure | 4 uni. Floor | 1 uni. A B C D E F G H 32 uni. 16 uni. 16 uni. 18 uni. 48 uni. 18 uni. 48 uni. 6 uni. X 4 mm | 2 uni. 5 mm | 1 uni. Not included Bubble Level Box Cutter 6mm Phillips Screwdriver | 2 uni. 2 I J 4 uni. 8 uni.
1 Remove the floor panels and the 3 PET layers from the floor structure. Unscrew the floor levelers to half their length (about 15 mm - 0.59 in), with exception of the center one, that should stay fully retracted. ~15mm | 0.59’’ 2 Level the floor structure using the 5mm Hex Key (X) - adjust the center leveler last and make sure it stays in contact with the floor.
3 Insert wooden dowels (A) in the floor structure according to the diagram. Step’s Material A 4 Screw the metal fittings (B) in the floor structure according to the diagram.
Insert the locking cams (C) in the Structure Pillars and insert the wooden dowels (A) in the top end of the structure pillars. Step 1 Step’s Material A 1 uni.
Fit the Structure Beams on the floor structure according to the diagram and rotate the locking cams (C) by hand using a screwdriver - make sure the beams are completely inserted before rotating the locking cams to the locked position.
Remove the top covers and the ceiling panels from the ceiling structure - the PET and Vicycle layers stay attached to the top cover. 8 Screw the metal fittings (B) in the ceilling structure according to the diagram.
9 Fit the ceiling structure on top of the structure beams according to the diagram and rotate the locking cams (C) by hand using a screwdriver - make sure the structures are completely inserted before rotating the locking cams to the locked position. 10 Fit the Side Panels - make sure the Side Panels are placed in the correct position by checking the diagram. The Side Panels are fixed using the 42mm screws (F) on the top and lower ends, and the 28mm screws (D) on the sides.
11Make sure the holes are aligned before placing the screws (You can use two screwdrivers to help align the holes in the center of the panel). This step must be executed by two persons. We advise one person to align the panels with the help of the Screwdrivers and the other one to fasten the screws. Step’s Material 6mm Phillips Screwdriver | 2 uni. Please follow the order of fixing the screws as described in the diagram and the indications concerning the type of screws to be used.
11 Carefully separate the Door Frame from the Door. 12 Fit the Door Frame using the 45mm screws (H) on the top and lower ends, and the 31mm screws (G) on the sides. Use the flat heads (E) and the 4mm Hex Keys (X).
13 Fit the door by carefully sliding the hinges down into the hinge shaft on the Door Frame. 14 In some cases, due to the unevenness of the floor, slight bend can occur on the door frame. It may be necessary to loosen and/or tighten some fixing screws on the door frame so that it stays as parallel as possible to the door and guarantees perfect contact between the two surfaces. ! Please re-check the leveling of the floor structure.
15 Place the PET layers in the Floor Structure. Fit the floor panel. Make sure the PET layers and the floor panel are placed in the correct position by checking the diagram.
16 Place the top cover on the ceiling structure according to the diagram. Fit the ceiling panels using the “J” screws.
17 Fit the ceiling panel using the “I” screws - make sure the ventilation slots are aligned with the slots on the underside of the top panels.
18 If you need to insert a cable into VicBooth Ultra, you must do so from the inside out. Lift the cable entry cover and force the plug through the layers of PET so that it runs out through the cutout made for this purpose.
Main Office, R&D & Logistics Avenida do Pólo 3, Nº 159, Carvalhosa 4590-137 Paços de Ferreira, Portugal Office Rua Quinta do Bom Retiro Nº 16, Armazém 9 2820-690 Charneca da Caparica, Portugal T (+351) 212 964 100 Info and Sales E sales@vicoustic.com www.vicoustic.com © Vicoustic, 2020 | V1 No parts of this document might be copied and/or published without written consent of Vicoustic.