User's Manual

88
The proles feature allows rapid access to pre-determined
combinations of settings that increase the speed and secu-
rity of workow. One example might be in a social situation
where there might be a need for formal outdoor portraiture
followed by informal indoor handheld ash-assisted wide-
angle shots, both situations requiring very dierent settings
in a stressful environment. By predetermining the relevant
settings required beforehand for each situation, they can be
saved collectively as a prole. By calling up the prole, you
can then be assured that all the settings are correct at the
press of one button.
For example, you might choose – autofocus single, brack-
eting, programmed exposure, etc – for outdoors. Once set,
you would click on the red PROFILES button, select a prole
name and press SAVE. A new name can be entered for the
new prole - ‘Outdoors’, for instance - and saved again. New
settings are made for the indoor shots changing to ash,
Pv setting, etc and the procedure repeated. By simply ac-
cessing ‘Outdoors’ or ‘Indoors’ in the prole list, all the rel-
evant settings will be instantly and correctly implemented
to match the situation.
There are eight proles: Default, Full auto, Studio, Fill
ash. two Action and two Spare reserved for customiza-
tion. All except Default can be changed and renamed.
The pre-set proles feature the following:
Default: normal ash sync, autofocus (single), single drive,
auto exposure (aperture priority), average metering, -None
Note
All settings, including those made on the sensor unit, are stored when a prole is created. This includes the ISO, white balance, color
temperature and color tint settings that were current at the time the prole was created. These prole settings will override the
settings in use at the time the prole button was pressed. In other words, remember to check for unintentional ISO, white balance
or color temperature changes when using proles. (Color tint is not a user setting but is stored after a manual white balance has
been made).
MAKING A PROFILE
1) Activate the camera and go through the various settings
(for example, autofocus, aperture priority, ll ash expo-
sure compensation, etc.) you require for the particular
purpose and save them as you go.
2) When all the required settings have been made, click (not
press!) the
PROFILES button (ON.OFF button) to access
the proles screen.
3) Use the scroll bar
to go through the list of proles. Choose a
Spare prole or a named prole (except Default). You can
either save the new prole under the original name or you
can change it
4) Press
Save (ISO/WB button). The Prole name screen is
then displayed where you can rename the prole to what
suits you (see under Image Info 4.2 for procedure details).
To use a prole from the main screen, press the PROFILES
button to reach the proles screen again. Scroll down the
list to the prole you want and then press the Load (AF) but-
ton. All the saved settings will then be automatically imple-
mented.
Full auto: normal ash sync, autofocus (single), single drive,
programmed exposure, centre weighted metering, -None
Studio: normal ash sync, manual focus, single drive, manu-
al exposure, spot metering, - AF
Fill ash: normal ash sync (adjusted output -1.7EV), auto-
focus (single), single drive, auto exposure, average metering.
Spare: customized proles.
The default setting is highlighted on the display for easy and
rapid access. Access to proles lower on the list is via a scroll
bar visible on the right of the display. Rotate the rear scroll
wheel to bring them into view.
All user proles can be restored to default values again sim-
ply by removing the battery and holding down the MENU
and ISO/WB buttons on the grip together and while keeping
them depressed, replace the battery. There will be an audible
signal that denotes the restoration.
There are two ways of making, saving and managing Proles:
1) Using the buttons on the grip
or
2) via the Camera Conguration tool in Phocus.
Note
If you decided to change the settings but nevertheless keep
the Prole name on the list, the new set of parameters will
be retained under that name. That is to say, the settings will
not be the same as listed here, despite the name. It might be
safer practice therefore to always change the prole name
to avoid later confusion.
PROFILES
SAVE
(ISO/WB)
LOAD
(AF)
PROFILES
(On/O)
(IS
(IS