V 1 S T E R E O T U R N TA B L E V PA - 5 8 3
OVERVIE W Top View Back Panel 45 RPM Adaptor Tone Arm Counter Weight Anti-Skating Knob Slipmat Tone Arm Lift Lever Tone Arm Turntable Platter Cartridge Function Knob Back View Remote Control Dust Cover Subwoofer RCA Output Optical In Record Line Jack Jacks Jack Speed Switch Subwoofer Pair Button (Wireless) Headphone Jack Aux-In Jack AC Power Port Power / Function Button Volume Control
Q U I C K S TA R T G U I D E FUNCTION KNOB - BASIC OPERATION POWER: VOLUME: Press and hold for 1-2 seconds to turn the unit ON or OFF. Rotate to raise or lower volume. FUNCTION KNOB - TO CYCLE THROUGH FEATURES VINYL: VINYL STREAM: BLUETOOTH: OPTICAL IN (TV): AUX-IN: OPERATION Press to enter record player function mode. Press to connect the unit to an external Bluetooth speaker. Press to pair the unit with a Bluetooth device (smartphone). Press to play audio from a connected TV.
S I M P L E S E T U P GETTING STARTED Remove the needle cover, by gently pulling towards the front of the unit. Carefully plug in the unit, install platter and tone arm weight. Note: It is recommended that this product should be operated only from the type of power source indicated on the rating label. This unit uses AC power and is powered by a standard wall outlet. BASIC OPERATION Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON or OFF.
T O N E A R M S E T U P ***IMPORTANT, THE TONE ARM MUST BE SET UP AS INSTRUCTED BELOW OR DAMAGE MAY OCCUR TO THE UNIT OR RECORDS. X X 0.5 0 TURN THE COUNTER WEIGHT ON THE BACK OF TONE ARM UNTIL THE TONE ARM IS FLAT AND BALANCED (SEE BOTTOM PICTURE) 2.5 0 REMOVE THE NEEDLE COVER - LIFT TONE ARM OUT OF THE HOLDER TO THE LEFT SO IT FLOATS FREELY - NOT TOUCHING ANYTHING 2 IDENTIFY THE WEIGHT ON THE BACK OF THE TONE ARM. USE THE INCLUDED 2.
V I N Y L P L AY I N G VINYL: Playing a Vinyl record Note: -Before using, make sure the tone arm is properly setup. See TONE ARM SETUP page. Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Simply press the Function Knob to make sure it is in Vinyl mode (the dial will illuminate white). Remove the needle cover, by gently pulling towards the front of the unit. Select the proper record speed (see back of unit). If using a 45 RPM record, use the included 45 adaptor.
BLUE TOOTH PAIRING BLUETOOTH: Connecting and playing music from a Bluetooth device (Smartphone). Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Simply press the Function Knob to make sure it is in Bluetooth mode (the dial will flash blue). On your device, turn Bluetooth ON. Then search for / select “V1 SYSTEM” in the settings menu. The unit will chime and say “Connected”, while the Function Knob will remain blue. Use your external device to control playback.
CARTRIDGE REPLACEMENT CARTRIDGE: VICTROLA VPC-190 REPL ACEMENT 2MM WHITE LEFT CHANNEL + RED RIGHT CHANNEL + The VPC-190 Cartridge is rated in excess of 1000 hours of normal use. As soon as you notice a change in sound quality or damage to the stylus, it is recommended that it be changed. 1. Unplug the unit and put the needle cover on the old cartridge. 2. Carefully remove all the wire leads from the back of the old cartridge. BLACK LEFT & RIGHT CHANNEL – 3.
W A R N I N G Important Safety Instruction 1. Read these instructions – All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions – The safety and operating instructions should be retained for future reference. 3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow all instructions – All operating and use instructions should be followed. 5.
S A F E T Y I N F O Safety Information 1. In order to shut off power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as during a vacation. 2. Use of controls, adjustments and performance of procedures other than those specified herein may result in hazardous radiation exposure. 3. To prevent electric shock, match wide blade of plug to wide slot, fully insert. 4.
- Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, jurisdiction to jurisdiction or country to country. All express and implied warranties for the product, including but not limited to any implied warranties of merchantability and fitness for a particular purpose, are limited in time to the term of this warranty.
