Manual EN Handleiding NL Manuel FR Anleitung DE Manual ES Användarhandbok SE MPPT 150/45-Tr MPPT 150/60-Tr MPPT 150/70-Tr MPPT 150/45-MC4 MPPT 150/60-MC4 MPPT 150/70-MC4 MPPT 150/85-Tr MPPT 150/100-Tr MPPT 150/85-MC4 MPPT 150/100-MC4 MPPT 250/60-Tr MPPT 250/70-Tr MPPT 250/60-MC4 MPPT 250/70-MC4 MPPT 250/85-Tr MPPT 250/100-Tr MPPT 250/85-MC4 MPPT 250/100-MC4 Appendix SmartSolar charge controllers
1. General Description EN Bluetooth Smart built-in: dongle not needed The wireless solution to set-up, monitor and update the controller using Apple and Android smartphones, tablets or other devices. NL VE.Direct port For a wired data connection to a Color Control, Venus GX, PC or other devices. FR Remote on-off input On/off control by a VE.Bus BMS when charging Li-ion batteries. DE Programmable relay Can be programmed (a.o. with a smartphone) to trip on an alarm, or other events.
Automatic battery voltage recognition The controllers will automatically adjust to a 12V, 24V or a 48V system one time only. If a different system voltage is required at a later stage, it must be changed manually, for example with the Bluetooth app or the optionel LCD display. Similarly, manual setting is required in case of 36V system. Flexible charge algorithm Fully programmable charge algorithm, and eight preprogrammed algorithms, selectable with a rotary switch.
EN NL FR DE Configuring and monitoring - Bluetooth Smart built-in: the wireless solution to set-up, monitor and update the controller using Apple and Android smartphones, tablets or other devices. - Use the VE.Direct to USB cable (ASS030530000) to connect to a PC, a smartphone with Android and USB On-The-Go support (requires additional USB OTG cable). - Use a VE.Direct to VE.Direct cable to connect to a MPPT Control, a Color Control or the Venus GX.
2. Safety instructions SAVE THESE INSTRUCTIONS - This manual contains important instructions that shall be followed during installation and maintenance. Danger of explosion from sparking Danger of electric shock ● Please read this manual carefully before the product is installed and put into use. ● This product is designed and tested in accordance with international standards. The equipment should be used for the designated application only. ● Install the product in a heatproof environment.
EN ● Use flexible multistranded copper cable for the battery and PV connections. The maximum diameter of the individual strands is 0,4mm/0,125mm² (0.016 inch/AWG26). NL A 25mm² cable, for example, should have at least 196 strands (class 5 or higher stranding according to VDE 0295, IEC 60228 and BS6360). An AWG2 gauge cable should have at least 259/26 stranding (259 strands of AWG26). Maximum operating temperature: ≥ 90°C.
3. Installation WARNING: DC (PV) INPUT NOT ISOLATED FROM BATTERY CIRCUIT. CAUTION: FOR PROPER TEMPERATURE COMPENSATION THE AMBIENT CONDITION FOR CHARGER AND BATTERY MUST BE WITHIN 5°C. 3.1 General ● Mount vertically on a non-flammable surface, with the power terminals facing downwards. Observe a minimum clearance of 10 cm under and above the product for optimal cooling. ● Mount close to the battery, but never directly above the battery (in order to prevent damage due to gassing of the battery).
3.3 PV configuration (also see the MPPT Excel sheet on our website) EN ● The controllers will operate only if the PV voltage exceeds battery voltage (Vbat). ● PV voltage must exceed Vbat + 5V for the controller to start. Thereafter minimum PV voltage is Vbat + 1V. ● Maximum open circuit PV voltage: 150V or 250V, depending on model. NL For example: 24V battery, mono- or polycristalline panels, max PV voltage 150V: ● Minimum number of cells in series: 72 (2x 12V panel in series or one 24V panel).
3.
EN A binary LED code helps determining the position of the rotary switch. After changing the position of the rotary switch, the LEDs will blink during 4 seconds as follows: Switch LED LED LED Blink position Bulk Abs Float frequency 0 1 1 1 Fast 1 0 0 1 Slow 2 0 1 0 Slow 3 0 1 1 Slow 4 1 0 0 Slow 5 1 0 1 Slow 6 1 1 0 Slow 7 1 1 1 Slow Thereafter, normal indication resumes, as described in the LEDs section. NL FR 3.
3.8 Battery charging information The charge controller starts a new charge cycle every morning, when the sun starts shining.
3.10 Pluggable LCD display - Live data NL The following information will be displayed if the "-" button is pressed (in order of appearance): Charger temperature (1) .,, °C/°F Notes: 1) A valid temperature is shown, --- = no sensor information or Err = invalid sensor data. 2) These items are only visible when relevant. ES Pressing the "-" button or the "+"button for 4 seconds activates the autoscroll-mode. Now all LCD-screens will pop-up one by one with short intervals.
Scrolling text Icons (1) Segments . . . . . . . .
Icons Segments Units , .-. A Function or parameter On/off switch Maximum charge current System voltage Charge algorithm (1) Absorption voltage (2) .-.-. V .-.-. V Float voltage (2) Equalization voltage (2) , , Automatic equalization (3) Manual equalization (4) .-.-. V Low battery voltage alarm clear .-.-. V High battery voltage alarm set .-.-. V High battery voltage alarm clear .-. V .-.-.
Notes: 1) The factory defined battery type can be selected with the rotary switch next to VE.Direct connector. The selected type will be shown here. The setting can alter between a factory defined type and "USER". 2) These values can ONLY be changed for the battery type "USER". The values in the table are for a 24V-battery. 3) Automatic equalisation can be set to “OFF” (default) or a number between 1 (every day) and 250 (once every 250 days). See section 3.8 for more details about automatic equalisation.
FR DE ES 11) Press SELECT: the text “” will blink, press SELECT again to reset to original factory settings. The charger will re-boot. The history data will not be affected (kWh counter, etc). 12) Press SELECT: the text “” will blink, press SELECT again to erase the history data (kWh-counter, etc). Note that this takes a few seconds to complete. NL 10) VE.Direct port TX pin mode (setting 58) Value Description 0 Normal VE.
4. Troubleshooting Problem Charger does not function Possible cause Solution Reversed PV connection Connect PV correctly Reverse battery connection Non replacable fuse blown.
n. a. High temperature: the thermometer icon blinks Err 2 Battery voltage too high (>76,8V) Err 17 Controller overheated despite reduced output current Err 18 Controller over-current Err 20 Maximum Bulk-time exceeded Err 21 Current sensor issue Err 26 Terminal overheated 17 Appendix The charge controller does not charge the battery SE n. a. ES The LCD does not light up (backlight works, no display, charger seems to work) DE n. a.
Error nr. Problem Err 33 PV over-voltage Err 34 PV over-current Err 38 Input shutdown due to battery over-voltage Inf 65 Communication warning Inf 66 Incompatible device Err 67 BMS connection lost Err 114 CPU temperature too high Err 116 Err 119 Calibration data lost Settings data lost Cause / Solution fasten bolts if possible. This error will auto-reset. This error will auto-reset after PV-voltage has dropped to safe limit.
5. Specifications, 150V models Charge algorithm Temperature compensation Battery reverse polarity (fuse, not user accessible) PV reverse polarity / Output short circuit / Over temperature -30 to +60°C (full rated output up to 40°C) 95%, non-condensing 5000m (full rated output up to 2000m) Indoor, unconditioned PD3 VE.
Specifications, 150V models continued SmartSolar charge controller Battery voltage Maximum battery current Nominal PV power, 12V 1a,b) Nominal PV power, 24V 1a,b) Nominal PV power, 36V 1a,b) Nominal PV power, 48V 1a,b) Max.
6. Specifications, 250V models Battery reverse polarity (fuse, not user accessible) PV reverse polarity / Output short circuit / Over temperature -30 to +60°C (full rated output up to 40°C) 95%, non-condensing 5000m (full rated output up to 2000m) Indoor, unconditioned PD3 VE.
Figure 1: Power connections Illustration 1 : Connexions électriques Abbildung 1: Stromanschlüsse Figura 1: Conexiones de alimentación Bild 1: Strömanslutningar
SmartSolar MPPT 150 I 85/100 – Tr dimensions SmartSolar MPPT 150 I 85/100 – Tr dimensions SmartSolar MPPT 150 I 85/100 – Tr Maße SmartSolar MPPT 150 I 85/100 – Tr dimensiones SmartSolar MPPT 150 I 85/100 – Tr dimensioner 23
SmartSolar MPPT 150 I 85/100 – MC4 dimensions SmartSolar MPPT 150 I 85/100 – MC4 dimensions SmartSolar MPPT 150 I 85/100 – MC4 Maße SmartSolar MPPT 150 I 85/100 – MC4 dimensiones SmartSolar MPPT 150 I 85/100 – MC4 dimensioner
Distributor: Serial number: Version Date : 04 : April 15th, 2019 Victron Energy B.V. De Paal 35 | 1351 JG Almere PO Box 50016 | 1305 AA Almere | The Netherlands General phone E-mail : +31 (0)36 535 97 00 : sales@victronenergy.com www.victronenergy.
