Concept Pro VHSD-810EXT Speed Dome System User Manual
Safety Information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning Precaution This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
Precautions Contents Operating Before using, make sure power supply and others are properly connected. While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and then contact your Special dealer. 4 Precautions 1. Introduction 7 Parts Name & Functions Handling Do not disassemble or tamper with parts inside the camera. Do not drop or subject the camera to shock and vibration as this can damage camera.
1 Product & Accessories Parts Name & Functions Please check if all the camera and accessories are included in the package. 1 Dome Cover 1 Main Body Camera module, screws, terminal block slot and DIP switches are included. 2 Lockup Screw Fixes main body to the surface mount bracket. 2 Surface Mount Bracket - It is used when installing the camera right on to the ceiling.
2 DIP Switch Setup DIP Switch Setup Before installing the camera, you should set the DIP switch to configure the camera ID, communication protocol. Bottom of Main Body If the pin is located ‘ON’ side of the printed label, it means on. In reverse, means off. ON 1 Pin On ON Pin Off 1 ON 1 2 3 4 5 6 7 8 Pin On/Off ON 2. Communication Protocol Setup 7 AD(American Dynamics) ON Choose the appropriate baud rate protocol by setting the DIP switch 1 2 3 4 5 6 7 8 DIP Switch for Communication 1.
2 Installation Using Surface Mount Bracket 1 Drilling the Hole on the Ceiling To pass cables through the ceiling, drill a hole (30mm diameter) on the ceiling panel. Installation Using Flush Mount Ring Bracket (Option) 1 Drilling the Hole on the Ceiling 1 Drilling the Hole on the Ceiling 2 Separate the Lock-up Screws from the 2 Fix the Surface Mount Bracket Pass the cables to the ¾” pipe hole, and screw the surface mount bracket to the ceiling.
2 Installation Using Ceiling Mount Bracket (Option) Installation Using Wall Mount Bracket (Option) 1. Installing on the Concrete Ceiling 1. Installing on the Concrete Wall 1 Drill the Ceiling and Fix the Anchor Bolts On the ceiling, drill a hole (6mm diameter/ 50mm depth), and fix the anchor bolts. 2 Fix the Ceiling Mount Bracket 1. Drill a hole (20mm diameter) on the pipe of the bracket to pass the cables. 2. On the fixed anchor bolts, attach the rubber gasket and screw the ceiling mount bracket. 2.
2 Cabling the 5P Terminal Block Cabling the 7P Terminal Block 1 Relay Out 5P Terminal Block BNC Video 2 Sensor/Alarm Input 5p terminal block connects the sensor/alarm input and the relay out device to the camer’s main body. (Refer ‘Installation Using Surface Mount Bracket’ of page 10 for the connection of the terminal block.) Relay Out Input Slot Sensor/Alarm Input Slot 1 Relay Out - It connects to the alarm lights, siren or lamps, and it is activated according to the OSD menu setting.
3 Check Points before Operation Main Functions Check Points before Operation 1 Preset - Max. 127 positions can be stored as preset positions. The preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. - Refer page 26 - ‘CONCEPT PRO SPEED DOME>FUNCTION SETUP>PRESET SETUP’ for more detailed information. 1. Before power is applied, please check the cables carefully. 2. The camera ID of the controller must be identical to that of the target camera.
OSD Information PRESET LABEL Preset Label 1 General Rules of Menu Operation PATTERN1 CONCEPT PRO SPEED DOME - - - - - - - - - - - - - - - - - - - - - - - 5 Action Title 6 Temperature 7 Alarm Input Information - - - This page explains how to operate the OSD menu using keyboard controller. a Read the manual of the keyboard controller.
3 OSD Menu Contents CONCEPT PRO SPEED DOME The 1st screen The 2nd screen Value CONCEPT PRO SPEED DOME The 1st screen The 2nd screen Value FOCUS MODE AUTO / MANUAL / SEMIAUTO PAL DIGITAL ZOOM ON / OFF PELCO-D IMAGE FLIP BAUD RATE 2400 ADDRESS COLOUR SYSTEM PROTOCOL ON / OFF WB MODE AUTO / MANUAL 1 RED ADJUST 10 ~ 60 CAMERA ID ON / OFF BLUE ADJUST 10 ~ 60 PTZ INFORMATION ON / OFF / AUTO BACK LIGHT OFF
OSD - CONCEPT PRO SPEED DOME & SYSTEM INFORMATION 1 CONCEPT PRO SPEED DOME - - - - - - - - - - - - - - - - - - - - - - - - - - - EXIT 1 CONCEPT PRO SPEED DOME To enter this screen, enter ‘Preset key + 95’. OSD - DISPLAY SETUP 1 Shows information and current configuration. Enable/Disable of OSD display on main screen.
OSD - MOTION SETUP MOTION SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - PRESET LOCK OFF PWR UP ACTION ON AUTO FLIP ON JOG MAX SPEED 140/SEC JOG DIRECTION NORMAL FRZ IN PRESET OFF BACK EXIT 2 Press Near/Enter Key PARKING ACTOIN - - - - - - - - - - - - - - - PARK ENABLE WAIT TIME PARK ACTION SETUP - - - - - - - - - - - OFF 00:10:00 HOME OSD - MOTION SETUP 1 MOTION SETUP Setup the general functions of pan/tilt motions.
OSD - FUNCTION SETUP > PRESET SETUP FUNCTION SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - BACK EXIT PRESET SETUP - - - - - - - - - - - - - PRESET NO. Press Near/Enter Key Moves to ‘PRESET SETUP’ screen. 1 UNDEFINED > Select , Press Near/Enter Key EDIT SCENE Moves to ‘VST SETUP’ screen. Refer page 28. Moves to ‘GROUP SETUP’ screen.
OSD - FUNCTION SETUP>VST SETUP FUNCTION SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - BACK EXIT 2 Press Near/Enter Key VST SETUP - - - - - - - - - - - - - - - - - - - - - - - VST NO. 1 1ST POS. NOT USED NOT USED 2ST POS. VST SPEED CLEAR VST BACK EXIT 30/SEC CANCEL - - - OSD - FUNCTION SETUP>PATTERN SETUP 2 VST SETUP - Up to 8 VST are available, which makes the camera to move slowly between two preset positions.
OSD - FUNCTION SETUP>GROUP SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - BACK EXIT GROUP SETUP - - - - - - - - - - - - GROUP NO. Press Near/Enter Key 1 UNDEFINED CANCEL > 30 VST3 1 Preset 120 > EDIT GROUP 1 - - - - - - - - - - - - - - - - - - - - - - - - - - NO. ACTION NO.
OSD - FUNCTION SETUP>SCHEDULE SETUP 1 FUNCTION SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - > BACK EXIT 2 Press Near/Enter Key SCHEDULE SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - MASTER ENABLE OFF DAY TIME ACT NO ON 1 UNDEFINED 2 UNDEFINED 3 UNDEFINED 4 UNDEFINED 5 UNDEFINED 6 UNDEFINED 7 UNDEFINED BACK > Joystick Down, Press Near Key 3 SCHEDULE SETUP - - - - - - - - - - - - - - - - - - - - -
OSD - CAMERA SETUP>WB SETUP CAMERA SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - SEMIAUTO FOCUS MODE DIGITAL ZOOM ON OFF IMAGE FLIP > BACK EXIT 2 Press Near/Enter Key WB SETUP - - - - - - - - - - - - - - - - WB MODE - RED ADJUST - BLUE ADJUST - - - - - - - - - - AUTO ----- Press Near Key, Joystic Down > - - - - - - - - - - MANUAL 30 40 CAMERA SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - SEMIAUTO FOCUS MODE DIGITAL ZOOM O
OSD - SYSTEM SETUP 1 SYSTEM SETUP - - - - - - - - - - - - - - - - - - - - - - - LANGUAGE ENGLISH 2 OSD - SYSTEM SETUP 1 SYSTEM SETUP - - - SET HOME POSOTION - - - - - - - - - - - - - - - - - - - - - - - - - - - Moves to ‘DATE/TIME SETUP’ screen. Refer screen 2 below. MOVE TO TARGET POSITION [NEAR:SELECT/FAR:CANCEL] 0/0/x1/E Moves to ‘PASSWORD’ setup screen. Refer screen 4 below.
3 OSD - SYSTEM INITIALISE 1 SYSTEM INITIALISE - - - - - - - - - - - - - - - - - - - - CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET CLR MOTIOM SET CLR FUNCTION SET REBOOT CAMERA REBOOT SYSTEM BACK EXIT - - - - - - NO NO NO NO NO NO NO 1 SYSTEM INITIALISE Initialises to the camera setting. 4 Dimensions Unit: mm CLEAR ALL DATA ON / OFF Deletes all configuration data such as display, camera, motion setup and so on. ¾” NPT CLR DISPLAY SET ON / OFF Initialises display configuration.
4 Dimensions of Option Brackets 1. Flush Mount Ring Bracket Unit: mm Dimensions of Option Brackets Unit: mm 2. Sun Shield Mount Bracket Unit: mm 3. Wall Mount Bracket Unit: mm 2. Ceiling Mount Bracket 112.6 4- 7 266 374.6 12 112.6 212 106 23 43 46 204 191 230 83 64 57.5 112 185 71.6 355.5 115 199.3 105 75 6- 2.5 10 25 161 57 140 141.5 70 164.6 4- 10 100 124.6 40 83.
4 Specifications Signal Format Image Device Camera NTSC PAL 1/4” Interline Transfer CCD Total Pixel 410K pixels [811 (H) x 508 (V)] 470K pixels [795 (H) x 596 (V)] Effective Pixel 380K pixels [768 (H) x 494 (V)] 440K pixels [752 (H) x 582 (V)] H. Resolution Color: 500 TV Lines S/N Ratio 50dB (AGC Off) Zoom x10 Optical Zoom & x10 Digital Zoom Focal Length F 1.8, f=3.8 ~ 38mm Min. Illuminance Color: 0.
