Concept Pro VHSD-810EXT Speed Dome System User Manual Rev 2.
Contents Before installing 1 Key features 2 Configure, fix and wire 3 Basic speed dome operation 5 Programming the speed dome 6 Running selected features 12 Specifications 13 Installer notes 14
Before installing ! - Installation should be carried out only by qualified personnel and in accordance with any wiring regulations in force at the time. - The speed dome is heavy and could cause injury if not correctly mounted in accordance with these instructions. Use only the fittings supplied with the speed dome and ensure that all lanyard safety cables are connected correctly during installation.
Key features Presets Up to 127 sets of positional and zoom level information can be stored as presets. These can be called manually by the operator, automatically by an alarm input, or grouped to form a sequence of actions to run automatically. Each preset supports titles of up to 10 characters and can also be programmed to activate the alarm output. Additionally, White Balance and Auto Exposure settings can be defined for each preset position if desired.
Configure, fix and wire Protocol & Baud rate DIP switch table 1. Change protocol, baud rate and ID if required The factory default setting is Pelco D, 2400, ID 1. Skip to section 2 if these settings match your control equipment. 1 2 Protocol/Rate OFF ON OFF ON OFF OFF ON ON Pelco D, 2400 bps Pelco D, 9600 bps Pelco P, 4800 bps Pelco P, 9600 bps ON 1 2 3 4 Factory default switch positions Note: Dip switches 3 & 4 are reserved and must not be changed.
3. Verify basic operation 2. Fix the ceiling mount base CONCEPT PRO SPEED DOME -----------------------FIRMWARE VER : 2.030V COLOUR SYSTEM : PAL PROTOCOL : PELCO-D BAUD RATE : 2400 ADDRESS : 1 DATA MEMORY : OK ZOOM MODULE : OK HOME TEACHING.. OK 1. Drill a hole in the ceiling to pass the cables through, and then fix the ceiling mount base using suitable fixings. 2. Make cable connections to the speed dome base for 12V DC power, video and RS-485 telemetry. 1.
Basic speed dome operation Programming, calling and deleting presets There are many different PTZ keyboards and DVR systems capable of controlling this speed dome, and it would be impossible to describe them all here. Therefore, examples given in this manual are based on using the Concept Pro VA-KBDPRO+ keyboard controller. Whilst the principles of operation are the same regardless of the control equipment used, you may need to refer to the manual supplied with your particular control equipment.
Programming the speed dome System information The speed dome setup menu allows the operator to customise and program all aspects of speed dome operation. All menu settings are retained in non-volatile memory so if power is lost to the speed dome for any reason, all settings will be retained.
Edit zone Privacy zone PRIVACY ZONE ----------------------------ZONE NO.
Alarm input setup ALARM INPUT SETUP ----------------------------N.OPEN ALARM 1 TYPE N.OPEN ALARM 2 TYPE NOT USED ALARM 1 ACT NOT USED ALARM 1 ACT BACK EXIT From the motion setup menu, use the joystick to highlight ALARM INPUT SETUP and key: NEAR ALARM 1,2 TYPE - each alarm input can be configured as Normally Open or Normally Closed. ALARM 1,2 ACT - for each alarm action, specify the preset number, VST function, pattern tour or group to call. Leave set to NOT USED to disable the alarm input.
VST setup Pattern setup VST SETUP ----------------------------1 VST NO. NOT USED 1ST POS. NOT USED 2ND POS. VST SPEED C L E A R VS T Group setup Edit pattern P A T T E R N SE T U P ----------------------------PATTERN NO. 1 UNDEFINED CLR PATTERN CANCEL < E D I T PA T T E R N > EDIT PATTERN 1 ----------------------------- GROUP SETUP ----------------------------1 G R O U P NO .
Edit group EDIT GROUP 1 ----------------------------N O A C T I O N ## # D W E L L O P T ----------------------------1 NONE 2 NONE 3 NONE 4 NONE 5 NONE ----------------------------SAVE CANCEL [NEAR:EDIT] Schedule setup Edit group EDIT GROUP 1 ----------------------------N O A C T I O N ## # D W E L L O P T ----------------------------1 PATTERN 1 00:03 1 2 PRESET 5 00:08 360 3 VST 3 00:03 8 4 PRESET 10 00:15 110 5 PRESET 4 01:30 55 ----------------------------SAVE CANCEL [NEAR:EDIT] SCHEDULE SETUP -------
Camera setup Z O O M C A M E R A SE T U P ----------------------------F O C U S MO D E SEMIAUTO DIGITAL ZOOM ON I M A G E FL I P ON < W H I T E B A L A N C E SE T U P > < A U T O EX P O S U R E SE T U P > BACK EXIT From the main menu, use the joystick to highlight CAMERA SETUP and key: NEAR FOCUS MODE MANUAL - the operator must focus the camera manually using the NEAR and FAR keys.
System setup SYSTEM SETUP ----------------------------C40 FAN RUN TEMP C5 HEATER RUN TEMP DATE 25/FEB/2008(MON) TIME 14:37:15(H/M/S) OFF C H E C K PA S S W O R D < E D I T PA S S W O R D > BACK EXIT EDIT PASSWORD ----------------------------[ ] ---------1234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:.
System initialise S Y S T E M IN I T I A L I S E ----------------------------C L E A R AL L D A T A NO CLR DISPLAY SET NO C L R C A M E R A SE T NO C L R M O T I O N SE T NO CLR FUNCTION SET NO REBOOT CAMERA NO REBOOT SYSTEM NO BACK EXIT Running selected features Installer notes Once pattern tours, groups and VST functions have been programmed in the speed dome setup menu, they can be accessed directly from the VA-KBDPRO+ by using the following sequences. 1.
Specifications Camera Pan / Tilt CCD ¼” Day / Night Resolution 500TVL (colour), 570TVL (B&W) Minimum Illumination 0.7 Lux (colour), 0.02 Lux (B&W) Optical Zoom 10x f=3.8 ~ 38mm (F1.8) Digital Zoom 10x (total zoom 100x with optical zoom) S/N Ratio 50db (AGC Off) Focus Auto / Semiauto / Manual White Balance Auto, Manual (Red and Blue adjust) Back Light Compensation On / Off General Pan: 360 degrees continuous rotation Speeds Manual / pattern tour: 0.
