INSTRUCTION MANUAL 19” HD Widescreen Water Resistant Television VSPA19LCD-AE1B Model No. VSPA19LCD-AE1M VSPA19LCD-AE1W IMPORTANT: Please read these instructions before installing and operating the unit. Retain them for future reference.
CONTENTS Safety Precautions ………………….………………………………………………..……. 3 What’s In The Box ………………….……………………………….………………..…… 4 Installation Procedure …………….……………………………………………..……... 5 Control Remotes ………………….……………………………………………...……….. 8 Basic Connections ……………...…….………..………………………………...……… 9 Extended Connections …………..…….………………………………...……………… 10 Touch Control Settings ………………………………………………..…………..……. 11 TV Operation …………………………………………………………………………………..
SAFETY PRECAUTIONS Handling the Power Supply Unit (PSU) Ensure the PSU is disconnected from the mains supply before connecting to the TV. Ensure the Earth pin on the mains plug is connected correctly. Do not use any PSU other than the one provided by Videotree. Ensure there is always easy access to the mains supply of the PSU. Do not remove the back cover There is risk of electric shock. There are no user serviceable parts inside. Do not expose to direct sunlight Avoid exposing the TV to direct sunlight.
WHAT’S IN THE BOX 1 x Wall Frame with Magnets 1 x Videospa TV 2 x AAA Batteries ( Master Remote ) 1 x Master Remote 1 x Silicone Grease Tube 1 x Videospa Waterproof Remote * 1 x Power Supply 1 x Power Lead OPTIONAL EXTRAS Installation Backbox 4 Removal Tool * Battery inside the remote (1 x CR2332). Remove the safety tab prior to use.
INSTALLATION PROCEDURE Backbox ( Optional ) * CUT OUT DIMENSIONS Without Backbox With Backbox D x 75mm D x 80mm Cut Out L x 530mm H x 335mm H x 330mm L x 525mm Cut Out * The Backbox is essential for environments where the TV will be subject to direct water e.g. under a shower. The Backbox is recommended for use with concrete walls. Please contact Videotree for information about an installation training course.
INSTALLATION PROCEDURE OPTIMAL VIEWING ANGLES 60° 60° INSTALLATION 1. Using the cutout template, mark the area on the wall where the TV will be positioned. Cut out this area. Take care ensuring the cut is accurate to ensure the frame and the Backbox* ( if it’s installed) are not distorted when fitted. 2. Position the Backbox into the wall, it must fit against the wall edge. Screw into position. Fill in any gaps with grout, between the Backbox and wall, and leave to set before continuing. 3.
INSTALLATION PROCEDURE 4. Screw the frame into position. If a Backbox is used then use the screws provided to fix the wall frame to the Backbox at the 4 corners. If a Backbox is not used then fix the wall frame straight to the wall using the multiple fixing holes that are available. The frame must be fitted with at least one fixing hole in each corner. Take care not to over tighten & bend the frame. Clean off the excess silicone sealant. Leave to set before continuing installation. 5.
CONTROL REMOTES MASTER REMOTE 1 Standby 8 Sound Mute 2 Numeric buttons Return Audio 3 Volume Up/Down 9 Programme Up / Down 10 OK Main Menu P 9-12 11 Exit 12 Direction Buttons 4 Select Source/Input P 13 Picture Mode N/A Sleep Sound Mode 5 Info P 13 Zoom 13 TV / Radio 6 Teletext N/A Freeze On/Off Favourite Channel List 14 Programme Guide P 12 15 Subtitles P 13 N/A WATERPROOF REMOTE 4 LED Indicator 7 Red, Green, Yellow, Blue Buttons: Selection, navigation and operation of various services.
BASIC CONNECTIONS CONNECTIONS HDMI SCART AV AUDIO IN CI SLOT AERIAL IN RS232 RJ12 IR OUT POWER IN PC VGA S-VIDEO YPbPr PC AUDIO (COMPONENT) AV VIDEO IN HEADPHONE OUT AERIAL, SPEAKERS & POWER L R +- - + HDMI & SCART Output DVD / VCR Set Top Box Aerial Input 9
EXTENDED CONNECTIONS RS232 CONNECTOR DB9 female connector. This port allows external equipment to send and acknowledge commands for control the Videospa TV. A standard RS232 cable should be used. DB-9 Pin 2 3 5 1 6 Signal Tx Rx Ground RS232 Protocol Baud Rate: 9600 bps Bits: 8 Parity: None Stop Bit: 1 COMMAND SEQUENCE A0 + F0 + 55 + FF + Code + Check-Sum. Code + Check Sum = 100 Hex e.g.
TOUCH CONTROL SETTINGS The Videospa TV has 3 different settings that improves the customer experience. To have access to these settings, the TV must be in STANDBY/OFF mode and only the master remote can be used. The waterproof remote has been locked to prevent any changes from unauthorised users. Red : Restore Factory Settings Blue : LED’s Flash Setting Green : Touch Sensitivity Yellow : Audio Beep Setting RESTORE FACTORY SETTINGS 1. Ensure TV is in standby. Press the RED button on the MASTER remote.
TOUCH CONTROL SETTINGS AUDIO BEEP SETTING For this setting there are 4 levels that enable/disable the audio beep response to touch and remote uses. The factory default setting is 2. 1. Ensure TV is in standby. Press the YELLOW button on the MASTER remote. 2. Scroll up or down with the arrow keys and save the changes with the OK button. 3. All the LED’s go off and after 2 seconds the standby LED’s go on (all red).
TV OPERATION AUTO TUNING (Analogue and Digital TV) 1. Press LCD MENU button. 2. Scroll left or right until reach CHANNEL menu. 3. Scroll down with the arrow keys and select Auto Tuning with the OK button. 4. Select the country with the left and right arrow keys and press the OK button twice . PROGRAMME EDIT 1. Press LCD MENU button. 2. Scroll down with the arrow keys and select Programme Edit with the OK button. 3. To Delete a channel, select the channel scrolling up or down with the arrow keys.
TV OPERATION PICTURE SETTINGS 1. Press LCD MENU button. 2. Scroll left or right until reaching the PICTURE menu. 3. Scroll with the arrow keys and save the changes with the OK button. Some modes are predefined and cannot be modified. SOUND SETTINGS 1. Press LCD MENU button. 2. Scroll left or right until reaching the SOUND menu. 3. Scroll with the arrow keys and save the changes with the OK button. Some modes are predefined and cannot be modified. TIME SETTINGS 1. Press LCD MENU button. 2.
TV OPERATION SETUP SETTINGS 1. Press LCD MENU button. 2. Scroll left or right until reaching the SETUP menu. 3. Scroll with the arrow keys and save the changes with the OK button. 4. This menu allows the menu language, the default audio language and default subtitle language to be changed. LOCK SETTINGS 1. Press LCD MENU button. 2. Scroll left or right until reaching the LOCK menu. 3. Scroll with the arrow keys and save the changes with the OK button. 4. This menu allows for specific channels to locked.
TV OPERATION PROGRAMME GUIDE 1. Press EPG/LIST button on the master remote or GUIDE on the waterproof remote. 2. Scroll with the arrow keys the move between channels and programmes. 3. To retrieve information of a programme, press the INFO button. 4. To Schedule a programme, scroll over the guide and press the Blue button. The Reminder Menu appears and change the details of the selected programme using the arrow keys. Once all the options have been set, press the OK button.
TECHNICAL SPECIFICATIONS Model: VIDEOSPA19-AE1 TV Unit Dimensions: W x H x D: 568 x 390 x 78mm VIDEO & AUDIO Input: (1) TV Format: DVB-T, PAL, SECAM Terminal: IEC 75 Ω Resolution: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Terminal: 3RCA green, blue and red colour (1) S-VIDEO Terminal: S-Video terminal black colour (1) CVBS Terminal: RCA Yellow colour (1) PC-RGB Format: Up to 1360*768@60Hz Colour: 1920*1080@60Hz 16bit, 24bit, 32bit Terminal: Video: VGA Sound: PC: Earphone input
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE No input power. No LED Light No signal transmitted / different source. Check correct source is selected No source cable is properly connected. Check cable connection between TV and source equipment. Source equipment is not setup correctly. Check the external equipment is on and set to display video on the required output port. Batteries ran out.* Replace the Batteries. No remote response No sound for PC input The waterproof remote comes with power LED .
APPENDIX A RS232 COMMANDS DATA CHECK DATA CHECK POWER COMMAND 0A F6 MENU COMMAND 0D F3 MUTE 0F F1 PMODE 1A E6 1 01 FF SMODE 51 AF 2 02 FE TV/RADIO 4D B3 3 03 FD SLEEP TIMER 0C F4 4 04 FC INFO 42 BE 5 05 FB ZOOM 12 EE 6 06 FA TTX 44 BC 7 07 F9 GUIDE 1C E4 8 08 F8 SUBTITLES 19 E7 9 09 F7 RED 16 EA 0 00 FF GREEN 17 E9 CH+ 1F E1 YELLOW 18 E8 CH- 1E E2 BLUE 19 E7 VOL+ 58 A8 DISCREET ON E0 20 VOL- 4B B5 DISCREET OF
Please make a note of the model and serial numbers: Model Number Serial Number Sales and Support Information ESC House South Road Weybridge Surrey KT13 9DZ Phone: +44 (0) 1932 856 382 Fax: +44 (0) 1932 856 649 E-mail: sales@videotree.com .