VideoWave Setup Guide Covers_AIM.fm Page 1 Monday, November 22, 2010 9:09 AM Setup Guide Guía de instalación Guide d’installation ©2010 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM320988 Rev.
00.Marley_Setup.book Page 2 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English SAFETY INFORMATION Please read this guide Please take the time to follow the instructions in this setup guide carefully. They will help you set up and operate your system properly and enjoy its advanced features. Please save all safety and operating instructions, including this guide, for future reference.
00.Marley_Setup.book Page 3 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 SAFETY INFORMATION • Allowing children to push, pull, or climb on the monitor may cause it to tip over, possibly resulting in personal injury or death. – For safety and greater stability, installation of the included anti-tip straps is recommended. – Be sure to install both anti-tip straps according to the instructions on page 10.
00.Marley_Setup.book Page 4 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English SAFETY INFORMATION Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
00.Marley_Setup.book Page 5 Monday, November 8, 2010 11:04 AM English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 CONTENTS WELCOME Thank you . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product overview . . . . . . . . . . . . . . . . . . . . . . . . . The setup process . . . . . . . . . . . . . . . . . . . . . . . . PHYSICAL SETUP Monitor placement and connections . . . . . . . . . . Monitor placement recommendations . . . . . . . . Placing the monitor with attached stand . . . . .
00.Marley_Setup.
00.Marley_Setup.book Page 7 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 WELCOME Thank you The setup process ® Thank you for purchasing the Bose VideoWave™ entertainment system. This guide provides you with step-by-step instructions for setting up your new entertainment system. Note: Professional installation is recommended.
00.Marley_Setup.book Page 8 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP Monitor placement and connections The monitor can be placed on furniture using the attached stand or it can be mounted on a wall. WARNING: The monitor weighs about 110 lbs. (49.9 kg). To prevent personal injury, a two-person lift is required. CAUTION: DO NOT mount or place the monitor in a recessed area or cabinet.
00.Marley_Setup.book Page 9 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP You need these items from Kit 1: Placing the monitor with attached stand 1. Place the monitor on a stable, flat surface capable of supporting the weight of the monitor. 11 Monitor Monitor AC power cord Monitor cable* 2. On the rear panel of the monitor, firmly pull out on the bottom of the connector cover to remove it.
00.Marley_Setup.book Page 10 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 3. Attach the monitor cable and AC power cord to the monitor as shown. 5. Plug the AC power cord from the monitor into a live AC (mains) outlet. 6. Go to “Control console placement and connections” on page 14 to continue the physical setup.
00.Marley_Setup.book Page 11 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP 1. Using a 5/32" (4 mm) T-handle hex wrench (not included), remove the top two bolts from the rear panel of the monitor as indicated. Bolts to remove CAUTION: The included screws are for use only into wood-studded wall constructions with one-inch (max.) drywall. For all other types of wall construction, please contact a professional installer.
00.Marley_Setup.book Page 12 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 5. Using a 7/64" (3 mm) drill bit (not included), drill four pilot holes. Wall-mounting the monitor 6. Secure each bracket to the wall using two of the provided screws. 1. Attach the wall-mounting brackets (not included) to the wall and monitor according to the instructions included with the wall bracket. 7.
00.Marley_Setup.book Page 13 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP 3. Remove the two stand bolts using a 5/32" (4 mm) Allen wrench (not included). WARNING: The monitor weighs about 110 lbs. (49.9 kg). To prevent personal injury, a two-person lift is required. 5. Lift the monitor off the stand. Stand bolt Stand bolt 4. Attach the monitor cable and AC power cord to the monitor as shown. 6.
00.Marley_Setup.book Page 14 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP Control console placement and connections You need these items from Kit 1: 11 CAUTION: If using the monitor on the stand, DO NOT place the control console between the legs of the stand or anywhere directly under the bottom edge of the monitor. This will avoid blocking ventilation and audio system openings in the product enclosure.
00.Marley_Setup.book Page 15 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP 2. Plug the free end of the monitor cable into the connector labeled A/V OUT to Monitor on the control console. 3. Plug the power supply output cord into the control console Power connector. Control console AC power cord Power Power supply A/V OUT to Monitor Monitor cable Power supply output cord 4.
00.Marley_Setup.book Page 16 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English INTERACTIVE SETUP Starting the system You are now ready to turn on your system and complete the setup process using the Unify intelligent integration system. TM You need these items from Kit 2: Kit 2 additional included items: These are items you may need to connect A/V devices to your system.
00.Marley_Setup.book Page 17 Monday, November 8, 2010 11:04 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 INTERACTIVE SETUP 1. Press the power button ( ) on the control console. The power light on the control console indicates the startup status. Note: When the system starts up, you will hear a start-up tone, and on the monitor screen you will see the Bose logo with a progress bar under it. 2. Slide the battery compartment cover off the back of the remote control.
00.Marley_Setup.book Page 18 Monday, November 8, 2010 11:04 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English INTERACTIVE SETUP 5. When the system is started up for the first time the following instruction appears on the monitor in many languages: “Press and hold the OK button on the Bose remote until the screen turns black.” If you have setup problems If you experience setup problems, the Unify intelligent integration system can help you identify the issue.
00.Marley_Setup.
VideoWave Setup Guide Covers_AIM.fm Page 1 Thursday, November 18, 2010 2:01 PM Setup Guide Guía de instalación Guide d’installation ©2010 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM320988 Rev.