O W N E R ’ S O P E R A T I N G M A N U A L 70 SERIES 1080p DLP™ PROJECTORS Vision 70 Vision 70/CineWide™ Vision 70/CineWide with AutoScope™ VERSION 1.
TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents.
EFFECTIVE WARRANTY DATE: This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date. IMPORTANT -- WARRANTY REGISTRATION: Y Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.
ADDITIONAL INFORMATION: To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited Warranty, please call or write: EL IM IN A R Y VIDIKRON Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-5900 Fax: (510) 324-5905 Toll Free: (888) 4VIDIKRON VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS _________________________________________________________ _____________________________
Safety Precautions Thank you for your purchase of this quality Vidikron video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Table of Contents 1 TWO YEAR LIMITED WARRANTY ............................................................................................. iii Safety Precautions ................................................................................................................... vi 1. Introduction ........................................................................................................................ 1 About This Manual .......................................................................
Table of Contents Mounting the Vision 70 .................................................................................................................................23 Floor Mounting (Upright) .....................................................................................................................23 Ceiling Mounting (Inverted) ................................................................................................................
Table of Contents 6. Serial Communications .................................................................................................... 65 RS-232 Connection and Port Configuration ..........................................................................................65 Serial Command Syntax ................................................................................................................................65 7. Specifications ...........................................................
Table of Contents PR EL IM IN A R Y Notes: x Vidikron Vision 70 Series Owner’s Operating Manual
1 List of Figures 2-1. Vision 70 Front/Side/Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2-2. Vision 70 Rear/Bottom/Side View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2-3. Vision 70 Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2-4. Vision 70 Remote Control .
List of Figures PR EL IM IN A R Y Notes: xii Vidikron Vision 70 Series Owner’s Operating Manual
1 This Owner’s Manual describes how to install, set up and operate the Vidikron Vision 70 Series Digital Light Processing (DLP™) Projectors. This product family consists of the Vision 70, Vision 70/CineWide™ and Vision 70/CineWide with AutoScope™ projectors. Introduction 1.1 About This Manual EL IM IN A R Y Throughout this manual, the Vidikron Vision 70 Series DLP Projectors are referred to collectively as the “Vision 70.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: TIPS highlight time-saving short cuts and helpful guidelines for using certain features. Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.
Introduction The Vidikron Vision™ 70 is our most affordable new 1080p projector. It has been designed to deliver the highest level of performance with expanded installation flexibility. The 1920 x 1080 native resolution DLP™ light engine incorporates all-new technology that works with our exclusive Imagix™ video processing to deliver amazing, ultra high definition images.
Introduction Key Features and Benefits ➤ The Vision 70 offers these key features and benefits: • Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio) • DLP system using high-performance Digital Micromirror Device (DMD) • 8-segment, 5x color wheel produces wide dynamic range and rich grayscale • V² Aperture Control (VAC) provides for infinitely variable adjustment of the light path through the optics, enabling the perfect balance of black and white levels for each individual installation • Picture in
2. Controls and Functions 2.1 Vision 70 at a Glance Figure 2-1 and Figure 2-2 show the key Vision 70 components. 3 2 EL IM IN A R Y 1 PR 4 9 8 7 5 6 Figure 2-1. Vision 70 Front/Side/Top View 1. VIDIKRON LOGO The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees. 2. TOP IR SENSOR 3.
Controls and Functions • Green during normal operation • Flashes green for 110 seconds after the projector is turned off to indicate that the lamp is cooling down 5. TEMP LED Indicates fan status and internal temperature as follows: • Off during normal operation • Red when internal temperature is too high INTAKE VENT 7. EXHAUST VENT 8. FRONT IR SENSOR 9. PROJECTION LENS EL IM IN A R 6. Y • Flashes red when the fans are not working or the lamp cover is open 2 3 4 PR 1 5 6 5 Figure 2-2.
CABLE ACCESS DOOR Open to access connectors. 2. DOOR RELEASE BUTTON 3. CABLE OPENING Pass cables through this opening. 4. LAMP MODULE COVER Remove this cover to access the lamp compartment. 5. FRONT/REAR ADJUSTERS Use these to adjust the projector height or projection angle. 6. CEILING MOUNT HOLES Use these to attach the ceiling bracket to the projector. EL IM IN A R 1. Y Controls and Functions To access the connector panel, press the door release button so it pops out.
Controls and Functions 1. HDMI (Digital) HDCP-compliant digital video input for connecting a DVD player or HD tuner with a DVI or HDMI output. 2. (For future use) DO NOT USE THIS CONNECTOR. Although it looks like a DVI input, it does not function like one and cannot be used as an additional video input. 3. COMP 1 (RCA connectors) Standard Definition (480i/576i) Component (YPrPb) input. This is the input for component video from sources such as DVD players.
Controls and Functions Figure 2-4 shows the Vision 70 remote control, and the paragraphs that follow describe its functionality. 1 4 EL IM IN A R 3 PR 5 6 Y 2 7 8 9 10 Figure 2-4. Vision 70 Remote Control Vidikron Vision 70 Series Owner’s Operating Manual 9 2.
Controls and Functions 1. ON / OFF Use these buttons to turn the projector on or off. 2. Source Selection Buttons: COMP 1 (SD Component) Press to select Component 1 (SD 480i/576i) video input as the source. S-VID (S-Video) Press to select the S-Video input as the source. Y VIDEO Press to select Composite video input as the source. EL IM IN A R COMP 2 (HD Component) Press to select Component 2 (HD 480p/576p/720p/1080i) video input as the source. RGB HD Press to select the Component 2 RGB input.
Controls and Functions 4. Memory Preset Buttons: MEM1 Press to recall settings for the current input from the “Custom 1” memory preset. ISF NT Press to recall settings for the current input from the “ISF Night” memory preset. DEF Press to recall the factory-default settings for the current input. Cursor Keys ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. EL IM IN A R 5.
Controls and Functions 9. Motorized Lens Controls: LENS SHIFT Press to access the lens shift controls. FOCUS Press to focus the image. ZOOM Press to reduce or enlarge the projected image size. 2.5 Remote Control/Built-In Keypad Functional Comparison EL IM IN A R Y 10. LIGHT Press to illuminate the buttons. Figure 2-5 shows remote control buttons that are duplicated on the built-in keypad.
3 3.1 Remote Control EL IM IN A R Y To install batteries in the remote control, push the battery cover and slide it off. Install the two AAA batteries with the correct polarity and then replace the cover. Installation • Make sure that the battery polarities are correct when installing the batteries. Notes on Batteries • Do not mix an old battery with a new one or different types of batteries.
Installation 3.2 Quick Setup Table 3-1 gives a quick overview of the Vision 70 installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. Y Table 3-1. Installation Overview Procedure PR EL IM IN A R Step For Details, Refer to page...
Installation Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. 3.3 Installation Considerations Installation Type Table 3-2.
Installation Throw Distance ➤ Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see Figure 3-1.
Installation Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Vertical and Horizontal Position Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in Figure 3-2.
Installation The Vision 70 provides up to 40% of vertical lens shift above and up to 50% of vertical lens shift below the screen center. For example, with a 96 x 54-inch (16:9) screen, you can shift the image up to 21.60 inches (0.55 meters) above or 27.00 inches (0.69 meters) below the screen center. Folded Optics ➤ In rear-screen applications where space behind the projector is limited, a mirror may be used to fold the optical path, as shown in Figure 3-4.
Installation If you are installing a Vision 70/CineWide or Vision 70/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor or fixed CineWide base plate. Note 3.4 Installing the Optional CineWide Lens Mount 1. Do not install the CineWide lens yet, only the fixed CineWide base plate or AutoScope lens motor. You will install the CineWide lens after you install the projector and adjust the primary lens. Y 2.
Installation Secure the motor to the projector with the eight screws and spacers provided for this purpose, as shown in Figure 3-5. EL IM IN A R Y 4. PR Figure 3-5.
Installation 5. Attaching the Ceiling Mount Extension Brackets: Use the supplied hardware to attach the ceiling mount extension brackets to the bottom of the projector as shown in Figure 3-6. PR Ceiling Mount Extension Brackets EL IM IN A R Y For ceiling installations, these brackets bring the mounting points for the projector mounting plate (included with the projector ceiling mount kit) from the bottom of the projector up and around the lens motor housing.
Installation Installing the Lens Base Plate (Vision 70/CineWide): To install the fixed CineWide base plate on a Vision 70/CineWide: 1. Place the projector upside down on a blanket or other soft surface. 2. Line up the four mounting holes on the CineWide base plate with those on the bottom of the projector. 3.
Installation There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. 3.5 Mounting the Vision 70 Floor Mounting (Upright) For fixed installations, and for those that want the projector out of sight or have a limited space for projector and audience, you can invert the Vision 70 and suspend it from the ceiling using a specially-designed ceiling mount fixture.
Installation 3.6 Connections to the Vision 70 Proceed as follows to connect the Vision 70 to your video sources, external controller(s) – if present – and AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. To access the connector panel, press the door release button so it pops out. Turn the knob clockwise or counter-clockwise and pull gently on it to open the door.
Installation RGB Connections: Connect your personal computer or other RGB source (DVD player or HD set top box) to the COMP 2/RGB input; see Figure 3-9. You can use the included DB15HD-to-5 x BNC cable if your RGB source has a 15-pin, VGA-type connector. The Vision 70 supports computer resolutions of 1024x768, 800x600 and 640x480. S-VID S-VID / Green Blue Red Horiz Vert DVD Player or HD Set Top Box Green Blue Red Horiz Vert Personal Computer PR Figure 3-9.
Installation Progressive Component Video Connections: Connect your progressive component source (DVD player or HD set top box) to the COMP 2/RGB input as shown in Figure 3-10. EL IM IN A R Y S-VID S-VID / Y Pb Pr DTV or Progressive Component (YPbPr) Source PR Figure 3-10.
Installation Composite/S-Video/Component Video Connections: Use the included cables to connect your composite, S-Video and SD (480i) component video sources to the Vision 70 as shown in Figure 3-11. PR EL IM IN A R Y S-VID S-VID / DTV Source, DVD Player, VCR, Satellite Receiver etc. Figure 3-11.
Installation RS-232 Controller ➤ Connection Connect a PC or home theater control/automation system (if present) to the RS-232 port on the Vision 70; see Figure 3-12. Use a standard, 4-wire RJ-11 telephone cable, wired straight-through. PR EL IM IN A R S-VID / S-VID Y For more information about using this connection, refer to Serial Communications on page 65. DTV Source, DVD Player, VCR, Satellite Receiver etc. Figure 3-12.
Installation If your Vision 70 is equipped with a CineWide with AutoScope system, use the cable supplied with the AutoScope Lens Motor to connect the motor to the 12-volt trigger output as shown in Figure 3-13. Y S-VID S-VID / EL IM IN A R 3.5-mm mini plug to AutoScope Lens Motor Figure 3-13.
Installation Connecting to AC Power ➤ Projector: The Vision 70 ships with various types of AC power cords. Choose the one that is appropriate to your locale. Power switch Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V). Then, connect the other end to your AC power source. EL IM IN A R Y AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power cord is provided for the lens motor.
Installation 3.8 Changing the OSD Language The Vision 70 OSD language is initially set to English, but can also display the menus in French, Spanish, Italian or German. To change the OSD language: 1. Press MENU. 2. Select Installation from the Main Menu and press ENTER. 3. Select Language from the Installation Menu and press ENTER. 4. Press or to highlight the desired language. (The change takes effect immediately.
Installation 3.11 Installing and Adjusting the CineWide Anamorphic Lens If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the CineWide anamorphic lens. Note It is extremely important that the primary lens is properly adjusted before you install the anamorphic lens. Ensure that the image from the primary lens is perfectly centered on the screen. Y The standard Vision 70/CineWide uses a prismatic-style anamorphic lens.
Installation 1. Use the Pitch/Y-Adjustment Screws and Washers (item #6) to attach the Vertical Mounting Brackets (item #5) to the Anamorphic Lens (item #1). 2. Place the lens with the brackets installed on top of (or under, if the projector is inverted) the Base Plate (item #2), so that the two threaded posts at the bottom of the brackets pass through the corresponding slots on the base plate. 3. Secure the lens assembly to the base plate with the Yaw/Z-Adjustment Levers and Fiber Washers (item #4).
Installation EL IM IN A R Incorrect Lens Angle Y Correct Lens Angle The anamorphic lens will almost always be angled with respect to the projector; this is normal. Once the proper lens angle has been set, firmly tighten the Pitch Adjustment Screws to secure the lens in place. Note There may be some pincushion distortion even after the lens is properly adjusted, especially at shorter throw distances.
Installation Once the proper lens angle has been set, firmly tighten the Yaw/Z-Adjustment Levers to secure the lens in place. The Vision 70 Anamorphic lens mount kit consists of everything shown in Figure 3-16. Some components shipped with your projector may differ slightly from what is shown in these instructions.
Installation Attach Lens Mounting Assembly to Lens Motor Carriage Plate: Remove the two Yaw/X Adjustment Levers and 1/4-20 Fiber Washers (item #8) from the bottom of the Anamorphic Lens Holder (item #5). 2. Place the Anamorphic Lens Holder on top of the AutoScope Carriage Plate (item #7). Position the bracket so that the long slot at the bottom of the lens holder is perpendicular to the corresponding slots on the carriage plate. 3.
Installation Configure Lens Motor Trigger: CineWide with AutoScope maintains constant image height independent of the aspect ratio, while using the full display resolution of the projector. It accomplishes this by moving the anamorphic lens in front of the primary lens when widescreen material is being viewed. When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens moves out of the light path.
Installation Adjusting the Height (Y): With the white field still on-screen, loosen the Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen: EL IM IN A R Y Too Low Correct position Too High When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in place.
Installation Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from side to side. Then, angle the lens to even out any left-right pincushion distortion: EL IM IN A R Y Anamorphic Lens (Top View) Correct Position Wrong Position PR Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to secure the lens in place.
Installation Adjusting the Geometry: Input an anamorphic cross-hatch test pattern to the projector. 2. Loosen the three Lens Rotation Set Screws (shown in Figure 3-17) on the lens adapter ring just enough to allow it to rotate freely. 3. Grasp the lens by the center ring and rotate the lens until the image is properly anamorphic: EL IM IN A R Wrong Position Y 1. When the image geometry appears correct, tighten the three Lens Rotation Set Screws to secure the lens in place.
4 Operation 4.1 Selecting Video Memory • Press the MEM1 button on the remote control to recall settings for the current input from the “Custom 1” memory preset. • Press ISF NT (Night) to recall settings for the current input from the “ISF Night” memory preset. • Press ISF DAY to recall settings for the current input from the “ISF Day” memory preset. EL IM IN A R Y • Press DEF to recall the factory-default settings for the current input. An on-screen confirmation message appears.
Operation 4.5 Using the On-Screen Menus • Press the MENU button on the remote control to display the Main Menu. To select a menu item, use the UP and DOWN buttons on the remote control to highlight it. Press ENTER or to confirm your selection. • Use the arrow buttons to select menu items or change settings. • Press EXIT to return to the previous menu. • Press MENU to turn off the OSD menu. (When the Main Menu is displayed, pressing EXIT also turns off the menu.
Operation Input Select Aspect Ratio Image Option SD Enhance Video Filter HD/RGB Adjust (480p and higher-res. signals only) H. Position V. Position Blue Enable Save Settings Load Saved Settings Default Sleep Timer Lamp Power Lamp Hours ICC Adjust Image Over Scan Video Black Level Aperture Control Image Shift Service Keystone OSD Position Horizontal/Vertical OSD Timer 0, 3, 6, 9 ...
Operation Main Menu ➤ The Main Menu is the starting point for accessing all projector functions. (The Service and ISF Calibration menus are hidden and not accessible until you enter a passcode.) Vision Model 70 Picture Adjust Image Option Projector Status Installation Service Picture Adjust Brightness 30 Contrast 15 Color 31 Tint 15 Sharpness 2 Color Temp. 2 NTSC To adjust a setting, use the or button to highlight it and use the change the setting. When finished, press EXIT.
Operation Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Vidikron recommends using the following calibration tools for best results: • External test pattern source -- Ovation Multimedia, Digital Video Essentials or AVIA test DVD or equivalent. • A blue filter (provided with many test DVDs), for color level and tint adjustments. Connect your test pattern source to the input that you are calibrating and proceed as follows.
Operation EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3. Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast from the Picture Adjust menu and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray Select Color from the Picture Adjust menu and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture Adjust menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the Sharpness setting to eliminate them. PR Figure 4-5.
Operation Note You must enter a passcode in order to enter the Service menu. Color Select: Use the Color Select menu to select the color space that is appropriate for the source signal, to achieve optimal color balance. If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space characteristics in the ICC Adjust sub-menu under the ISF Calibration menu, described later in this section. (The Standard color space is factory-set and not adjustable.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Anamorphic (16:9) Remote Control Key Description ANA EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) 4:3 Image, stretched to fill 16:9 Screen (Display) Standard 4:3 4X3 4:3 Image on 16:9 Screen (Display) Letterbox LBOX PR 4:3 Image on 16:9 Display (Letterbox aspect ratio) IntelliWide I-WIDE 4:3 Image on 16:9 Screen (Display) Select Anamorphic to view 16:9 DVDs and HDTV programs in their native aspect ratio.
Operation Table 4-1. Aspect Ratio Settings (continued) Remote Control Key Cinema CINEMA Description Select Cinema to view 2.35 source material in its native aspect ratio. EL IM IN A R 2.35:1 Image on 16:9 Screen (Cinema aspect ratio / no CineWide) 2.35:1 Image on 2.
Operation Video Filter: The Video Filter setting controls the behavior of the Sharpness control. The available settings depend on the vertical resolution of the input signal, as follows: • With a 480i signal, you can apply the sharpness control to either the input signal (1), the output signal (2), both (3) or neither (0). • With a 480p or higher-resolution signal, the sharpness control is applied only to the output signal and only when you set the Video Filter to “on” (1).
Operation Lamp Hours: Lamp Hours indicates how long the currently-installed lamp has been in service. (This part of the menu is read-only.) To access the Installation adjustments, press MENU, then press the or button to highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. Press EXIT to return to the previous menu or press MENU to close all menus.
Operation Service ➤ Service White Balance To access advanced projector settings, use the up- or down-arrow keys to select Service from the Main Menu and press ENTER. Use the number buttons on the remote to enter the Service menu passcode when prompted and press ENTER again. Then, press MENU on the remote control. Gamma Selection ICC Adjust Image Over Scan Note Video Black Level You only need to enter the Service menu passcode the first time you select that menu after turning on the projector.
Operation ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL color space characteristics. To do this, select the color space to modify. Then, select a component color (Red, Green, Blue, Yellow, Cyan or Magenta). For each component color, you can adjust the following: • Intensity: This slidebar adjusts the intensity – also known as luminance – of a given color. • Sat. This slidebar adjusts the color saturation level – the amount of that color in a video image.
Operation Image Shift: The Image Shift menu allows you to precisely center the image on the screen. (These controls are available only with a 480i source signal.) • Horizontal: This control moves the image right or left within the area of available pixels. • Vertical: This option moves the image up or down within the area of available pixels. Note 1. To adjust the image position with a 480p or higher-resolution source, use the HD/RGB Adjust controls in the Option menu, described on page 52.
Operation RS-232 Baud Rate: To change the data rate of the projector’s RS-232 input, select RS-232 Baud Rate from the Service menu. Set it to either 9600, 38400 or 115200, to match the data rate of the computer or control system connected to the projector. Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the Vision 70 will respond. The Primary IR code is permanently set to +20. The secondary IR code is also +20.
Operation ISF Calibration ➤ ISF Calibration To access the ISF Calibration menu, select ISF Calibration from the Main Menu and press ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu passcode when prompted and press ENTER again. Then, press MENU on the remote control. Picture Adjust White Balance Gamma Selection Note This menu should be used by ISF-certified technicians only.
Operation Splash Screen Timer: Use the or button to set the Splash Screen Timer. This timer controls how long the startup (ISF and Vidikron logo) image stays on-screen after you turn on the projector. Select from 5 to 60 seconds, in one-second increments. When finished, press EXIT. ISF Enable: Select ISF Enable from the ISF Calibration menu to control the display of the ISF logo on the Vision 70 splash screen upon power-up.
Operation PR EL IM IN A R Y Notes: 60 Vidikron Vision 70 Series Owner’s Operating Manual
5 Maintenance and Troubleshooting Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Remove the three screws from the lamp cover. 3. Remove the lamp cover. 4. Remove the two lamp assembly mounting screws. 5. Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing. 6. Install the new lamp module and replace the two screws. 7.
Maintenance and Troubleshooting 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 70. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Vidikron Technical Support. Table 5-1. Troubleshooting Chart Possible Cause(s) The projector does not turn on. • • • Securely attach the lamp cover.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Solution • The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the Vision 70. • Ensure that the source outputs are connected to the correct Vision 70 input. TEMP and LAMP LEDs are both flashing red. • • The lamp cover is open. Fans are not working properly. • • Close the lamp cover. Please contact your Vidikron dealer for assistance.
Maintenance and Troubleshooting PR EL IM IN A R Y Notes: 64 Vidikron Vision 70 Series Owner’s Operating Manual
Serial Communications 6 To interface the Vision 70 with a home theater automation/control system or a PC running terminal emulation software: Connect it to your control system or PC as shown in Figure 3-12. 2. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. 3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to match that of the projector (115200, 38400 or 9600). 4.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1. Serial Commands (continued) Code Function Vertical Lens Shift = Max. Down x283x Zoom = Max. Out x284x Zoom = Max.
7 7.1 Vision 70 Specifications Table 7-1 lists the Vision 70 specifications. Table 7-1.
Specifications Table 7-1. Vision 70 Specifications (continued) Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications Brightness*: 14.7 to 21.5 foot-Lamberts (fL) Contrast Ratio*: 195:1 to 218:1 *Variable depending on Aperture Control setting EL IM IN A R Y These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.
Specifications Table 7-1. Vision 70 Specifications (continued) Regulatory Approvals: Complies with FCC, CE C-Tick Limited Warranty: Projector: Two (2) years parts and labor from the date of delivery to the end user. Lamp: 1000 hours or six (6) months, whichever comes first. PR EL IM IN A R Y Specifications are subject to change without notice.
Specifications 7.2 Vision 70 Dimensions Figure 7-1 shows the Vision 70 dimensions. 14.9 in. (379.68 mm) 6.9 in. (175.00 mm) Y 18.9 in. (480.00 mm) EL IM IN A R 11.0 in. (280.25 mm) 4.1 in. (103.89 mm) 22.0 in. (560.51 mm) 8.0 in. (203.00 mm) 8.8 in. (222.50 mm) 4.4 in. (110.80 mm) 17.3 in. (440.00 mm) PR 13.0 in. (330.00 mm) Figure 7-1.
Appendix A. Personalizing the ISF Splash Screen on the Vision 70 This Appendix describes how to personalize the ISF splash screen on the Vidikron Vision 70 Series DLP Projectors. Y Only ISF-trained and -certified technicians should attempt this procedure! EL IM IN A R Note Connect a PC to the Vision 70 RS-232 port and establish a serial connection; refer to RS-232 Connection and Port Configuration on page 65 if you need instructions. 2. Press MENU on the projector remote control.
Personalizing the ISF Splash Screen on the Vision 70 9.
RUMA-011225 rev. 12-15-06 v1.0 Vidikron 2900 Faber Street Union City, CA 94587 510-324-5900 Fax 510-324-5905 1-888-4-VIDIKRON www.vidikron.
