O W N E R ’ S O P E R A T I N G M A N U A L 10/12 DLP™ PROJECTORS VERSION 2.
TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents.
EFFECTIVE WARRANTY DATE: This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date. IMPORTANT -- WARRANTY REGISTRATION: Y Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.
ADDITIONAL INFORMATION: To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited Warranty, please call or write: EL IM IN A R Y VIDIKRON Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-5900 Fax: (510) 324-5905 Toll Free: (888) 4VIDIKRON VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS _________________________________________________________ _____________________________
Safety Precautions Thank you for your purchase of this quality Vidikron video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Table of Contents 1 TWO YEAR LIMITED WARRANTY ............................................................................................. iii Safety Precautions ................................................................................................................... vi 1. Introduction ........................................................................................................................ 1 About This Manual .......................................................................
Table of Contents Connections to the Vision 10/12 ................................................................................................................22 Connector Panel Access ........................................................................................................................22 Connecting the Vision 10/12 to Source Components................................................................22 RS-232 Controller Connection ........................................................
1 List of Figures 2-1. Vision 10/12 Top/Front/Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2-2. Vision 10/12 Rear/Top/Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2-3. Vision 10/12 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3-1.
List of Figures PR EL IM IN A R Y Notes: x Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
1 This Owner’s Manual describes how to install, set up and operate the Vidikron Vision Model 10 and Model 12 DLP Projectors. Throughout this manual, the Vidikron Vision 10/Vision 12 DLP Projector is referred to simply as the “Vision 10/12.” 1.1 About This Manual Target Audience Y Vidikron has prepared this manual to help home theater installers and end users get the most out of the Vision 10/12.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: TIPS highlight time-saving short cuts and helpful guidelines for using certain features. Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.
Introduction Vidikron proudly introduces its most affordable home theater projectors to date -- the Vision Model 10 and Model 12. The Vision 10/12 offers a performance feature set based on the latest generation of DLP™ light engines with Vidikron’s exclusive Imagix™ video processing technology to produce outstanding blacks, superior contrast performance, maximum screen brightness and an accurate color palette. 1.
Introduction Parts List ➤ Your Vision 10/12 is shipped with the following items. If any items are missing or damaged, please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON. • Vision 10/Vision 12 DLP Projector • AC Power Cord (North America) • AC Power Cord (Europe) • Remote Control Unit and two (2), AAA-size batteries • HD 15-pin VGA to HD 15-pin VGA cable • DVI-D to DVI-D cable • Composite video cable (RCA) Y • DVI-to-HDMI adapter • +12-Volt Trigger adapter (3.
Controls and Functions 2 Figure 2-1 and Figure 2-2 show the locations of key Vision 10/12 projector components. Front/Top/Side View Y 2 EL IM IN A R 1 11 10 PR 9 8 7 6 5 4 3 Figure 2-1. Vision 10/12 Top/Front/Side View Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 5 2.
Controls and Functions TOP IR SENSOR 2. VERTICAL LENS SHIFT DIAL Shifts the image up or down. 3. INTAKE VENT 4. ADJUSTABLE FEET Use to adjust the height or projection angle. 5. VIDIKRON LOGO The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees. 6. FRONT IR SENSOR 7. FOCUS/ZOOM RING EL IM IN A R Y 1. 8. EXHAUST VENT 9.
Controls and Functions Rear/Top/Side View 2 3 5 4 1 HDMI HDMI EL IM IN A R 7 Y 8 PR 6 10 Figure 2-2.
Controls and Functions 1. COMPOSITE VIDEO INPUT Standard composite video input for connecting a VCR, camcorder, laser disc player or other composite video source. 2. S-VIDEO Standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR. 3. COMPONENT VIDEO (RCA connectors) Standard-definition (480i/576i) or high-definition (720p/1080i), YPrPb component input. This is the input for component video from sources such as DVD players.
Controls and Functions Figure 2-3 shows the Vision 10/12 remote control, and the paragraphs that follow describe its functionality. 1 EL IM IN A R 3 4 11 12 13 5 6 7 14 8 PR 9 15 Y 2 10 Figure 2-3. Vision 10/12 Remote Control Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 9 2.
Controls and Functions 1. ON / OFF Press to turn the projector on or off. 2. IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted. 3. Source Selection Buttons: VIDEO Press to switch to the Composite video input. EL IM IN A R RGB HD Press to switch to the RGB HD input. Y COMP 1 (Component 1) Press to switch to the Component 1 (480i/576i/720p/1080i) video input. S-VID 1 (S-Video) Press to switch to the S-Video input.
Controls and Functions 9. Not used. 10. LIGHT Press this button to illuminate the buttons. 11. CUST Press to recall settings for the current input from the “Custom” memory preset. 12. ISF NIGHT Press to recall settings for the current input from the “ISF Night” memory preset. 14. EXIT Press this button to exit the current menu and return to the previous one. PR EL IM IN A R 15. NUMBER KEYS Use these buttons to enter menu passcodes. Y 13.
Controls and Functions PR EL IM IN A R Y Notes: 12 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
3 3.1 Remote Control To install batteries in the remote control: Press down the tab on the cover and pull the cover in the direction of the arrow. 2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment. 3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place. EL IM IN A R Y 1. Installation • When installing batteries, make sure that the battery polarities are correct.
Installation Notes on Remote Control ➤ Operation The remote control can be used to control the projector within the ranges shown in Figure 3-1. 30° 23'(7 m) EL IM IN A R Y 45° 45° 23'(7 m) 30° PR Figure 3-1. Available Range of the Remote Control Note The signal from the remote control can be reflected by the screen. • For best results, hold the remote control within 23 feet (7m) of the back or top sensor and aligned within 30°.
Installation Table 3-1 gives a quick overview of the Vision 10/12 installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. For Details, refer to page... Procedure EL IM IN A R Step Y Table 3-1.
Installation 3.3 Installation Considerations Installation Type ➤ Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. Table 3-2.
Installation Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see Figure 3-2.
Installation Vertical and Horizontal ➤ Position Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in Figure 3-3.
Installation 150% Width Lens Shift (1.5 x W) 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Center EL IM IN A R Y 0% Screen Width (W) PR Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example. Figure 3-5.
Installation Table 3-3 gives the lens shift limits for the Vision 10 and Vision 12, as percentages and absolute measurements with a 96 x 54 inch (1.78:1) screen. Table 3-3. Vertical and Horizontal Lens Shift Limits Vision 10 Vision 12 Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1 and 2) Horizontal (Note 2) Up 40% 46% Down 60% 63% Left 8% Right 8% Y Vertical (Notes 2 and 3) EL IM IN A R Lens Shift Limits in Inches, with a 96-by-54 inch (1.78:1) Screen Up 21.60 24.
Installation There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. Mounting Floor Mounting: In typical front and rear screen installations the projector can be mounted to a secure and level surface, such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation.
Installation 3.4 Connections to the Vision 10/12 Proceed as follows to connect the Vision 10/12 to your video sources, external controller(s) – if present – and AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. • Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Y Route all cables through the opening on the rear underside of the projector.
Installation COMP 2 PR/CR PB/CB PB/CB PR/CR Y COMP 2 Y PB/CB Y RGB-HD Y PR/CR RGB-HD PB/CB PR/CR S-VIDEO HDMI HDMI COMP 1 VIDEO VIDEO S-VIDEO COMP 1 RS-232 EL IM IN A R Y RS-232 PR HDMI or DVI Source (DVD Player or HD Set Top Box) Note: To connect a DVI source, use the HDMI-to-DVI adapter and DVI cable provided with the projector. Figure 3-7.
Installation RGB-HD Connections: The Vision 10/12 has an RGB input for connecting a personal computer or DTV decoder with an RGB output. See Figure 3-8. COMP 2 PR/CR PB/CB Y RGB-HD HDMI PB/CB PR/CR Y COMP 2 Y PB/CB Y PB/CB PR/CR RGB-HD PR/CR S-VIDEO HDMI COMP 1 VIDEO VIDEO S-VIDEO COMP 1 RS-232 PR EL IM IN A R Y RS-232 Personal Computer Figure 3-8. Analog RGB Connections Note 1.
Installation Component Video Connections: If you have a DVD player or DTV decoder with a component (YPbPr) output, connect it to the COMP 1 or COMP 2 input as shown in Figure 3-9. COMP 2 PR/CR PB/CB PB/CB PR/CR Y COMP 2 PB/CB Y RGB-HD Y PB/CB Y PR/CR RGB-HD PR/CR S-VIDEO HDMI HDMI COMP 1 VIDEO VIDEO S-VIDEO COMP 1 Y RS-232 EL IM IN A R RS-232 Y PR Pr/Cr Pb/Cb Component Video Source (DVD Player or HD Set Top Box) Figure 3-9.
Installation Composite/S-Video Connections: The Vision 10/12 has S-Video and composite video inputs for connecting a DVD player, VCR, satellite receiver, camcorder, laser disc player et cetera; see Figure 3-10. COMP 2 PR/CR PB/CB PB/CB Y COMP 2 Y PR/CR PB/CB Y RGB-HD HDMI Y PB/CB PR/CR RGB-HD PR/CR S-VIDEO HDMI COMP 1 VIDEO VIDEO S-VIDEO COMP 1 Y RS-232 EL IM IN A R RS-232 PR Composite S-Video DVD Player, VCR, Satellite Receiver etc. Figure 3-10.
Installation Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation system (if present) to the RS-232 port on the Vision 10/12; see Figure 3-11. For more information about using this connection, refer to Serial Communications on page 55.
Installation If your home theater contains a retractable screen or other, 12-Volt trigger-activated equipment, connect it to the 12-volt trigger output on the Vision 10/12 as shown in Figure 3-12. COMP 2 PR/CR PR/CR Y PB/CB PB/CB Y PB/CB COMP 2 PB/CB PR/CR Y RGB-HD HDMI Y PR/CR S-VIDEO RGB-HD COMP 1 VIDEO HDMI Connecting to the 12-Volt ➤ Trigger Output VIDEO S-VIDEO COMP 1 Y RS-232 EL IM IN A R RS-232 3.
4 4.1 Turning on the Power Turn on your source components. 2. Plug the female end of the power cord into the AC receptacle on the rear of the Vision 10/12 (AC 100V ~ 240V). 3. Connect the other end to your AC power source. The power indicator lights blue to indicate that the Vision 10/12 is in “standby” mode. 4. Press the ON button on the remote control to turn on the projector. The power indicator turns off. 5.
Operation 4.3 Changing the OSD Language 1. Press MENU. 2. Select Installation from the Main Menu. 3. Select Language from the Installation Menu. 4. Press or to select the desired language. The change takes effect immediately. EL IM IN A R Y By default, the Vision 10/12 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation.
Operation The Vision 10/12 gives you a great deal of control over the picture size, position and focus. Figure 4-2 shows the location of the focus and zoom controls; Figure 4-3 shows the location of the lens shift controls. To focus the projected image, rotate the focus ring left or right. Focus/Zoom EL IM IN A R Y To make the picture larger (zoom in), rotate the zoom ring to the left, toward the Vidikron logo. To make the picture smaller (zoom out), rotate the zoom ring to the right.
Operation Shift ➤ To change the projected image position, rotate the vertical and/or horizontal lens shift dials. Note Do not force the lens shift dials beyond their respective ranges. This may cause the projector to malfunction. Lens shift dial (Vertical) PR EL IM IN A R Y Lens shift dial (Horizontal) 4.6 Using the On-Screen Menus Figure 4-3. Vertical and Horizontal Lens Shift Controls To use the on-screen menus: 1. Press MENU to display the Main Menu. 2.
Operation (not available on HDMI or RGB-HD inputs) 1, 2, 3, 4, 5 1.0, 1.5, 1.8, 2.0, 2.2, 2.35, 2.5, 2.8 Native, 5,000K, 5,500K, ...
Operation Main Menu ➤ The Main Menu is the starting point for accessing all projector functions. (The ISF Settings menu is grayed out and not accessible until you enter a passcode.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Anamorphic (16/9) Remote Control Key Description ANA EL IM IN A R Y 16:9 Image on 16:9 Screen Select Anamorphic to view 16:9 DVDs and HDTV programs in their native aspect ratio. 4:3 images are stretched horizontally to fit a 16:9 screen. 4:3 Image on 16:9 Screen Standard (4/3) 4X3 Active Image Area (4:3) Standard 4:3 scales the input signal to fit in the center of the 16:9 screen.
Operation Table 4-1. Aspect Ratio Settings (continued) Aspect Ratio Remote Control Key Cinema Fill C-FILL Description EL IM IN A R Y 2.35:1 Image on 16:9 Screen A 2.35 image is stretched anamorphically in both directions to fill a 16:9 image. 2.35:1 Image on 16:9 Screen with Cinema Fill Picture Adjust ➤ Picture Adjust Brightness 0 Contrast 0 Color 0 Tint 0 Sharpness 3 Color Temp ICC Select White Balance Save Settings 2.
Operation Connect your test pattern source to the input that you are calibrating and proceed as follows. Perform the adjustments in the order listed here. Below Black Above Black EL IM IN A R Y Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-5 shows a typical PLUGE pattern. Figure 4-5.
Operation EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-6. Figure 4-6. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast from the Picture Adjust menu. Using the left- and right-arrow ( ) buttons, adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and contrast controls are interactive.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray Select Color from the Picture Adjust menu. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture Adjust menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-8. Adjust as needed, looking for white edges around the transitions from black to gray and different sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. PR Figure 4-8.
Operation Color Temperature: To adjust the color temperature, select Color Temp from the Picture Adjust menu and press ENTER. (Color temperature defines the “color of gray.”) The range is from 5,000K to 10,000K, in increments of 500K. The default setting, 6,500K, is appropriate for most situations. Higher settings produce a “bluer” picture; lower ones impart a reddish hue to the image. Table 4-2.
Operation ICC Select: Choose ICC Select from the Picture Adjust menu to specify the color space (Standard, NTSC, HDTV or PAL) that is appropriate for the source signal, to achieve optimal color balance. If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space characteristics in the ICC Adjust sub-menu under the ISF Settings menu, described later in this section. (The Standard color space is factory-set and not adjustable.
Operation • Auto Tune: Auto Tune automatically adjusts settings to optimize computer images. Auto Tune can be executed either on command or automatically whenever an incoming RGB signal is present. To execute Auto Tune on command, select Execute Auto Tune and press ENTER. To enable automatic Auto Tune, select Auto Tune and set it to ON. Note Auto Tune may take some time to complete, depending on the characteristics of the incoming signal.
Operation Source : Information: Select Information from the Main Menu to see information about the current source, input resolution, horizontal and vertical frequencies, lamp hours and the installed firmware version. Component 1 Resolution: 720 x 480 Vert Freq : 60 Hz Horz Freq : 31 kHz Lamp Timer : F/W Version : Should you ever need to contact Vidikron Technical Support, this information will help them answer your questions or resolve product performance issues.
Operation Keystone Correction: If the projector and screen are not installed perpendicular to each other, the image may become distorted in a trapezoidal shape, as shown in Figure 4-10. Select Keystone from the Installation menu to compensate for this. Projector EL IM IN A R Y Horizontal Keystone Correction Projected Image Positive values compress right side; Negative values compress left side. Vertical Keystone Correction PR Positive values compress top; negative values compress bottom.
Operation ISF Settings ➤ Use the ISF Settings menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only. ISF Calibration Brightness 0 Contrast 0 Color 0 Tint You must enter a passcode to access the ISF Settings menu. 0 Sharpness 3 Gamma Several controls in this menu are identical to those in the Picture Adjust menu, but are accessible only by entering the ISF Calibration menu passcode.
Operation ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL color space characteristics. To do this: 1. Select ICC Adjust from the ISF Calibration menu and press ENTER. 2. Select the color space to modify using the left- or right-arrow buttons. 3. Select a component color (Red, Green, Blue, Cyan, Yellow or Magenta).
Operation Blue Enable: Refer to Blue Enable on page 44. Splash Screen Timer: Press the right- or left-arrow buttons to set the Splash Screen Timer. This timer controls how long the startup (ISF and Vidikron logo) image stays on-screen after you turn on the projector. Select from 15 to 60 seconds, in 5-second increments. PR EL IM IN A R Y Noise Reduction: To apply Digital Noise Reduction (DNR) to the input signal, select Noise Reduction from the ISF Calibration menu.
5 Maintenance and Troubleshooting 5.1 Cleaning the Projector • Unplug the power cord before cleaning the projector. • Avoid using benzene or thinner, as these can damage the finish on the projector exterior. Y • Do not use volatile agents, such as insecticides, on the projector. EL IM IN A R • Do not leave rubber or plastic objects in contact with the projector for long periods as they may damage the finish of the projector. • Wipe off dirt gently with a soft flannel cloth.
Maintenance and Troubleshooting 5.3 Cleaning the Intake and Exhaust Vents This Vision 10/12 is equipped with intake and exhaust vents to allow the flow of cool air through the projector and maintain the proper operating temperature. Side and front view EL IM IN A R To clean the intake and exhaust vents: Y You should periodically clean the vents by vacuuming them with a vacuum cleaner.
Maintenance and Troubleshooting The projector lamp has a life of 2,000 hours. Maintain proper ventilation to keep the lamp operating throughout its lifetime. Do not subject the projector to unnecessary vibration. 5.4 Lamp Maintenance • Lamp replacement is recommended after approximately 2,000 cumulative hours of use or when you notice a significant deterioration in the picture and color quality.
Maintenance and Troubleshooting 1. Turn off the projector and wait for the cooling fan to stop. 2. Unplug the power cord. Allow the projector to cool down for approximately one hour prior to removing the lamp assembly for replacement. 3. Loosen the two captive lamp cover screws and remove the cover. EL IM IN A R Y 5.6 Lamp Replacement Loosen the four lamp assembly mounting screws. 5. Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing.
Maintenance and Troubleshooting Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 10/12. If you encounter an issue not described here, please contact your Vidikron dealer or Vidikron Technical Support. Table 5-1. Troubleshooting Chart The projector does not turn on after initial installation. Possible Cause(s) • • • Ensure that the Vision 10/12 is plugged in and that the AC outlet is active. Replace the batteries.
Maintenance and Troubleshooting PR EL IM IN A R Y Notes: 54 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
Serial Communications 6 To interface the Vision 10/12 with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-11. 6.1 RS-232 Connection and Port Configuration Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 9600, to match that of the Vision 10/12 RS-232 port. Y Table 6-1 lists the RS-232 command set.
Serial Communications Table 6-1. Serial Commands (continued) Command Description Reply Selects the LETTERBOX aspect ratio RRDOK RRD03 Selects the INTELLIWIDE aspect ratio RRDOK RRD04 Selects the CINEMA (2.35:1) aspect ratio RRDOK RRD05 Selects the CINEMA FILL aspect ratio RRDOK RRE00 Turns the projector OFF RREOK PON Turns the projector ON Random (Note 2) Y RRD02 EL IM IN A R Notes: 1. All image quality settings must be made with the remote control.
7 7.1 Vision 10/12 Specifications Table 7-1 lists the Vision 10/12 specifications. Table 7-1.
Specifications Table 7-1. Vision 10/12 Specifications (continued) 0.25 Amps, active when the projector is turned on Power Requirements: 100 to 240 VAC (auto-sensing), 50/60 Hz, 370 Watts Operating Environment: 41°F to 95°F (5°C to 35°C), 0% to 90% humidity (non-condensing) Dimensions: See Figure 7-1 Weight (including lens): 27.5 lbs. (12.47 kg) Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications Brightness: 15.9 foot-Lamberts (fL) (Vision Model 10); 16.
Specifications 7.2 Vision 10/12 Dimensions Figure 7-1 shows the Vision 10/12 dimensions. Rear View Y 15.66in 398.0mm 16.90in 429.4mm 16.99in 431.6mm 7.15in 181.8mm 6.54in 166.3mm 6.48in 164.6mm 6.48in 164.6mm 0.89in 22.8mm PR Front View 4.09in 103.9mm 9.12in 231.7mm 6.40in 162.6mm EL IM IN A R Side View 16.06in 408.0mm Side View Bottom View 3.42in 87mm 3.42in 87mm Figure 7-1.
Specifications 7.3 Computer Signal Compatibility The Vision 10/12 can display video signals from a variety of computer sources via its RGB-HD and HDMI inputs. It is compatible with the three most common sync modes -- sync-on-green, composite sync and RGB with separate sync -- as well as XGA display adapters that use advanced intelligent compression. Table 7-2 lists the signal types that are compatible with the Vision 10/12, and indicates which of those are VESA standards. Table 7-2.
Specifications Table 7-2. Computer Signal Compatibility Chart (continued) PC PC SVGA XGA MAC 13” VGA MAC 16” SVGA MAC 19” XGA 800 x 600 800 x 600 Vertical Frequency (Hz) 31.4 50 35.1 56 √ √ 37.9 60 √ √ 44.5 70 48.1 72 √ √ 46.9 75 √ √ √ √ VESA Standard HDMI Support Display √ Upscale √ 53.7 85 56.8 90 √ 64.0 100 √ 35.5 43 √ 40.3 50 √ 48.4 60 √ √ 56.5 70 √ √ 60.0 75 √ √ 68.7 85 √ √ 73.5 90 77.2 96 80.6 100 640 x 480 34.
Specifications 7.4 Video Signal Compatibility Table 7-3 lists numerous common video signal formats and indicates which input(s) on the Vision 10/12 can accept a given format. Table 7-3. Video Signal Compatibility Chart SD Video Compatible Inputs (Note 1) H-Freq V-Freq Comp. Comp. SCom(kHz) (Hz) VGA 1 2 Video posite √ √ √ √ Y Resolution √ √ √ √ √ √ √ √ NTSC 640 x 480i 15.73 59.94/ 60 PAL 768 x 576i 15.63 50 EL IM IN A R SECAM NTSC4.
RUMA-011175 rev. 08-14-06 v2.0 Vidikron 2900 Faber Street Union City, CA 94587 510-324-5900 Fax 510-324-5905 1-888-4-VIDIKRON www.vidikron.
