I N S T A L L A T I O N / O P E R A T I O N M A N U A L 140/150 1080p LightAmp™ Digital Projector Vision 140 Vision 140/CineWide™ Vision 140/CineWide™ with AutoScope™ Vision 150 Vision 150/CineWide™ Vision 150/CineWide™ with AutoScope™
TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers from Vidikron, a business of Runco International, LLC (“Vidikron”) Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY: Y This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act.
RIGHTS, LIMITS AND EXCLUSIONS: THE FOREGOING DESCRIBED WARRANTIES ARE THE ONLY WARRANTIES THAT APPLY TO THE PRODUCTS. VIDIKRON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. VIDIKRON’S LIABILITY RELATED TO THE PRODUCT IS LIMITED TO THE COST OF THE APPLICABLE REMEDY AS NOTED ABOVE.
COPYRIGHT AND TRADEMARKS: © Copyright 2008 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of Runco. The trademarks reporduced in this Vidikron Owner’s Manual and used on the Vidikron Products are either owned by Runco or are licensed by Runco.
Important Safety Instructions Thank you for your purchase of this quality Vidikron video product! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation.
19. Never look directly into the lens when the lamp is on.
FCC PART 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1 TWO YEAR LIMITED WARRANTY ............................................................................................. iii Important Safety Instructions ................................................................................................. vi Compliance Information ......................................................................................................... vii 1. Introduction ......................................................................................
Table of Contents Installing the Projection Lens ......................................................................................................................26 Installing the Optional CineWide Lens Mount ......................................................................................27 Remove Projector Front Feet (CineWide with AutoScope) ......................................................27 Install Anamorphic Lens Motor (CineWide with AutoScope) or Base Plate (fixed CineWide) ..........
4. Operation .......................................................................................................................... 63 Using the On-Screen Menus ........................................................................................................................63 Main Menu .................................................................................................................................................65 Input Source .....................................................
Table of Contents PR EL IM IN A R Y Notes: xii Vision Model 140/150 Installation/Operation Manual
1 List of Figures 2-1. Vision 140/150 Top/Rear/Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2-2. Vision 140/150 Input Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2-3. Vision 140/150 Rear-Panel Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2-4. VHD Controller Front Panel . . .
List of Figures 4-6. Keystone Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 5-1. Removing the Lamp Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 5-2. Unlocking the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 5-3.
1 This Owner’s Manual describes how to install, set up and operate a Vidikron Vision Model 140 or Model 150 LightAmp™ Projector and VHD Controller. Introduction 1.1 About This Manual Y Throughout this manual, the Vidikron Vision Model 140/150 LightAmp™ Projector and VHD Controller are referred to as the “Vision 140/150.” The information in this manual applies to both projector models except where otherwise indicated.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: TIPS highlight time-saving short cuts and helpful guidelines for using certain features. NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.
Introduction Vidikron’s Vision Model 140 and Model 150 bring our most advanced technology, 1080p resolution and the world’s first THX® Certified home video products together in truly awesome fashion. The Vision 140/150 uses a new, ingeniously engineered 3-chip DLP™ light engine, combined with an advanced Xenon LightAmp™ lamp illumination system to bring astoundingly high performance and ultra-high resolution to the very best home theaters on the planet.
Introduction Key Features and Benefits ➤ The Vision 140/150 offers these key features and benefits: • Native Resolution: 1920 x 1080 • Three-chip Digital Light Processing (DLP) system • Two HDMI Inputs (on VHD Controller) with High-bandwidth Digital Content Protection (HDCP) • HDTV Compatible • Multiple lens options for stunning sharpness and throw distance flexibility Parts List ➤ Your Vision 140/150 is shipped with the following items.
Controls and Functions 2 2.1 Vision 140/150 at a Glance EL IM IN A R Y Figure 2-1 shows the key Vision 140/150 components. 2 4 PR 1 3 5 AC IN 220V 50HZ 6 7 8 9 10 11 Figure 2-1.
Controls and Functions TOP IR SENSOR 2. BUILT-IN KEYPAD The built-in keypad is located at the back of the projector, beside the input panel. Use it similarly to the TheaterMaster Remote Control to perform service-related tasks on the projector. 3. INPUT PANEL Connect the VHD Controller outputs here. 4. LED STATUS DISPLAY Indicates current operating status of the projector. 5. LAMP COVER Remove this cover to access the lamp compartment. 6. REAR FOOT (Stationary) 7.
Controls and Functions 2.2 Vision 140/150 Input Panel Figure 2-2 shows the Vision 140/150 rear input panel. 2 3 4 5 6 7 8 9 EL IM IN A R Y 1 11 10 Figure 2-2. Vision 140/150 Input Panel RS232 IN Connect the RS-232 output from the VHD Controller here, using the provided RJ11-to-DB9 adapter and communication cable. 2. RS232 OUT Not used. 3. RS422 Not used. 4. GPIO Not used. 5. REMOTE Wired input from an external remote control or infrared receiver. 6.
Controls and Functions Figure 2-3 shows the Vision 140/150 rear-panel keypad. 1 2 3 4 5 6 7 8 9 10 EL IM IN A R Y 2.3 Vision 140/150 Rear-Panel Keypad 12 11 PR Figure 2-3. Vision 140/150 Rear-Panel Keypad 1. LED STATUS DISPLAY The LED status window displays an active pattern of segments to indicate the projector is changing its state from powered down to powered up. The message “On” appears in the display when the projector has completed its initialization and is ready for use. 2.
Controls and Functions 9. Menu Navigation Buttons: UP BUTTON ( ) Used to move the menu cursor up in the Vision 140/150 menu system. LEFT BUTTON ( ) Used to move the menu cursor left in the Vision 140/150 menu system. RIGHT BUTTON ( ) Used to move the menu cursor right in the Vision 140/150 menu system. Y DOWN BUTTON ( ) Used to move the menu cursor down in the Vision 140/150 menu system. EL IM IN A R ENTER BUTTON When an item is highlighted on the On-Screen Display, the ENTER button selects the item.
Controls and Functions 2.4 VHD Controller Front Panel Figure 2-4 shows the controls and indicators on the VHD Controller front panel; the paragraphs that follow describe them. 480i V150 EL IM IN A R Y Component SD NTSC 16:9 1 2 3 PR Figure 2-4. VHD Controller Front Panel 1. POWER BUTTON Press once to toggle from standby mode to on mode. Press it again to return to standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control. 2.
Controls and Functions 2.5 VHD Controller Rear Panel Figure 2-5 shows the rear connector panel on the VHD Controller. 7 3 9 SYSTEM CONTROL INTERFACE CAUTION INPUTS Serial No R/Pr G/Y B/Pb RISK OF ELECTRIC SHOCK DO NOT OPEN H V ! AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR TRIGGERS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.
Controls and Functions 9. IR Wired input from a wired remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows: Ring = +5V Tip = IR Input Sleeve = Ground Note When an external remote control or infrared receiver is connected to the wired IR input, the IR sensor on the front of the VHD is disabled. Y 10. RS-232 CONTROL PORT A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system. EL IM IN A R 11.
Controls and Functions Figure 2-6 shows the Vision 140/150 remote control, and the paragraphs that follow describe its functionality. 1 2 Y 3 6 8 9 12 13 15 17 18 7 10 11 14 16 PR 5 EL IM IN A R 4 19 22 20 21 Figure 2-6. VHD Controller/Vision 140/150 Remote Control Vision Model 140/150 Installation/Operation Manual 13 2.
Controls and Functions 1. IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted. 2. LIGHT Press to illuminate the buttons. 3. ON / OFF Press to turn the projector on or off. 4. ENT (Enter) Press to select a highlighted menu item or confirm a changed setting. Y On some remote control units, this button is where the RETURN/EXIT button (item #6) appears here. EL IM IN A R Note 5.
Controls and Functions Memory Preset Buttons: 8. ISF NT (Night) Press to recall settings for the current input from the “ISF Night” memory preset. 9. ISF DAY Press to recall settings for the current input from the “ISF Day” memory preset. 10. CUST 2 Press to recall settings for the current input from the “Custom 2” memory preset. 11. CUST 1 Press to recall settings for the current input from the “Custom 1” memory preset. EL IM IN A R 13.
Controls and Functions PR EL IM IN A R Y Notes: 16 Vision Model 140/150 Installation/Operation Manual
3 Installation 3.1 Remote Control To install batteries in the remote control: Battery Installation Remove the battery cover from the back of the remote control. 2. Insert the batteries included with the remote control. Ensure that the polarities correctly match the and markings inside the battery compartment. 3. Replace the battery cover. EL IM IN A R Y 1. 1. Do not mix an old battery with a new one or different types of batteries. Note 2.
Installation • Do not drop the remote control or expose it to moisture or high temperature. • The remote control may malfunction under a fluorescent lamp. If that occurs, move the VHD Controller away from the fluorescent lamp. • Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the VHD Controller or projector. • If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.
Installation Table 3-1 gives a quick overview of the Vision 140/150 installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. Table 3-1. Installation Overview For Details, Refer to page...
Installation 3.3 Installation Considerations Installation Type ➤ Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. Table 3-2.
Installation Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see Figure 3-2.
Installation Vertical and Horizontal ➤ Position Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in Figure 3-3.
Installation 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Center EL IM IN A R Screen Width (W) Y 0% PR Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example. Figure 3-5.
Installation Table 3-4 lists the lens shift limits for each available Vision 140/150 lens, as percentages and absolute measurements with a 100 x 56 inch (1.78:1) screen. Table 3-4. Vertical and Horizontal Lens Shift Limits Lens Option B or C D E Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1, 2 and 3) 60% Down 60% Left 22% 20% 21% Right 22% 20% 21% EL IM IN A R Horizontal (Note 2) Up Y Vertical (Notes 2 and 3) Lens Shift Limits in Inches, with a 100-by-56 inch (1.
Installation In rear screen applications where space behind the projector is limited, a mirror may be used to fold the optical path, as shown in Figure 3-6. The position of the projector and mirror must be accurately set. If you are considering this type of installation, contact your dealer for assistance. Folded Optics Screen Figure 3-6.
Installation 3.4 Installing the Projection Lens The projection lens is shipped separately from the projector. Proceed as follows to install the projection lens: Remove the lens plug from the lens opening in the projector. 2. Place the lens cap on the projection lens to protect it from being damaged during the installation process. 3. Remove the rear cap from the lens. This protective cap is only used during shipping to protect the lens from damage. 4.
Installation If you are installing a Vision 140/150 with the optional CineWide or CineWide with AutoScope system, proceed as follows to install the anamorphic lens mounting assembly (stationary base plate or AutoScope lens motor). Note 3.5 Installing the Optional CineWide Lens Mount 1. Do not install the CineWide lens yet, only the mounting plate or lens motor. You will install the CineWide lens after you install the projector and adjust the primary lens.
Installation Caution (Skip this step if you are installing a fixed CineWide anamorphic lens, or ceiling-mounting an AutoScope-equipped projector.) If you are installing the Vision 140/150 in an upright position (not ceiling-mounted), use the supplied hardware to attach the projector stand to the bottom of the projector as shown below. This stand allows the projector to lie flat on the mounting surface with the AutoScope lens motor installed.
Installation There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. 3.6 Mounting the Vision 140/150 Floor Mounting (Upright) For fixed installations, and for those that want the projector out of sight or have a limited space for projector and audience, you can invert the Vision 140/150 and suspend it from the ceiling using a specially-designed ceiling mount fixture.
Installation 3.7 Connections to the Vision 140/150 and VHD Controller Proceed as follows to connect the VHD Controller to the Vision 140/150, your video sources, external controller(s) – if present – and AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. To access the connector panel, press the door release button so it pops out.
Installation Connect your video sources to the VHD Controller as shown and described in the sections that follow. HDMI Connections: See Figure 3-10. Use the HDMI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector.
Installation Digital (DTV) RGB or Component Video Connections: See Figure 3-11. R/Pr G/Y INPUTS B/Pb H V TRIGGERS HD1 1 2 3 HD2 R/Pr G/Y B/Pb H V S-Video 1 Pb HDMI 2 Pr Y Component Video Video S-Video 2 EL IM IN A R Y HDMI 1 PR Red/Pr Green/Y Blue/Pb Horiz Vert DTV or Progressive Component (YPbPr) Source Figure 3-11.
Installation Analog (Computer) RGB Connections: See Figure 3-12. R/Pr G/Y INPUTS B/Pb H V TRIGGERS HD1 1 2 3 HD2 R/Pr G/Y B/Pb H V S-Video 1 Pb HDMI 2 Y Pr Component Video Video S-Video 2 EL IM IN A R Y HDMI 1 Vert PR Red Green Blue Horiz Personal Computer Figure 3-12.
Installation Composite/S-Video/Component Video Connections: See Figure 3-13. R/Pr G/Y INPUTS B/Pb H V TRIGGERS HD1 1 2 3 HD2 R/Pr G/Y B/Pb H V S-Video 1 HDMI 2 Pb Y Pr Component Video Video S-Video 2 EL IM IN A R Y HDMI 1 PR Pb Pr Y DVD Player, VCR, Satellite Receiver, Laser Disc etc. Figure 3-13.
Installation Use a straight-through, 9-pin RS-232 cable to connect a PC or home theater control/automation system (if present) to the RS-232 Control port on the VHD Controller; see Figure 3-14. For more information about using this connection, refer to Serial Communications on page 91.
Installation Connecting 12-Volt Trigger ➤ Outputs to External Theater Equipment If your Vision 140/150 is equipped with a CineWide with AutoScope system, connect the AutoScope lens motor to a 12-volt trigger output on the VHD Controller; see Figure 3-15. Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or screen masks) to the other trigger outputs. AutoScope Lens Motor (Rear) Y AC Input EL IM IN A R Power Switch 3.
Installation If infrared signals from the remote control cannot reach the VHD Controller due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR receiver to the VHD Controller to extend the range of the remote control. See Figure 3-16.
Installation 3.8 Turning on the Power 1. Turn on your source components. 2. Turn on the main power switch at the rear of the VHD Controller. 3. If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input (see Figure 3-15). 4. Press the ON button on the remote control – or the POWER button on the VHD Controller front panel – to turn on the system.
Installation By default, the Vision 140/150 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this: Select an input OTHER THAN HDMI 1 or HDMI 2 on the VHD Controller. 2. On the VHD Controller, press MENU and enter the Service Menu passcode. 3. Select Service from the Main Menu. 4.
Installation 3.11 Installing and Adjusting the CineWide Anamorphic Lens If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the anamorphic lens. Note that some components shipped with your projector may differ slightly from what is shown in these instructions. Note Remove the two Z-Adjustment Levers and 1/4-20 Fiber Washers from the bottom of the lens mounting assembly. 2.
Installation (Skip this step if you are installing a fixed CineWide anamorphic lens.) CineWide with AutoScope maintains constant image height independent of the aspect ratio, while using the full display resolution of the projector. It accomplishes this by moving the anamorphic lens in front of the primary lens when widescreen material is being viewed. When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens moves out of the light path.
Installation Height (Y) Adjustment: With the white field still on-screen, loosen the Height Adjustment Levers on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen: EL IM IN A R Y Too Low Correct position Too High When the height is properly set, tighten the Height Adjustment Levers to secure the lens in place. PR Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion.
Installation Yaw Adjust: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from side to side. Then, angle the lens to even out any left-right pincushion distortion: EL IM IN A R Y Anamorphic Lens (Top View) Correct Position Wrong Position Geometry: PR Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to secure the lens in place. 1. Input an anamorphic cross-hatch test pattern to the VHD Controller. 2.
Installation 3. Grasp the lens by the front ring and rotate the lens until the image is properly anamorphic: Wrong Position When the image geometry appears correct, tighten the three Lens Rotation Set Screws to secure the lens in place. (When viewed from the front, the rear opening on the anamorphic lens should appear as a tall, narrow oval.) PR Focus: Finally, rotate the Focus Ring on the anamorphic lens to fine-tune the optical focus.
Installation After you have installed and adjusted the projector and lens (or lenses), you are ready to begin calibrating the DVI input (Input 2) to the Vision 140/150. Note Vidikron calibrates both the Vision 140/150 and VHD Controller at the factory for optimum performance in most typical home cinema environments, before the system ships. Y Carefully assess the displayed image quality before proceeding with calibration.
Installation SYSTEM 1 MAIN 11 LENS 2 FUNCS 3 4 SOURC EL IM IN A R Y 12 + PREV CH - 13 - GUIDE 5 + MENU 6 7 8 14 PR EXIT 15 INFO 9 10 DIS Figure 3-17.
Installation 1. POWER Button Hold this button down for 1-2 seconds to turn on or off the projector. 2. FUNCS Button This button brings you to a sub-page in which you can access the projector’s internal test patterns, view help text, auto-calibrate the projector and perform various other functions. 3. BACKLIGHT Button Lights the LCD display and buttons for use in a dark room. 4. LCD Display Displays currently-selected LCD Menu page. 5. MAIN Button Brings up the Main LCD Menu page. 6.
Installation Navigating the Projector ➤ Menus To select a sub-menu using the remote keypad, do one of the following: VIDIKRON VISION 150 Size and Position Picture Quality Channel Setup Installation Lamp Adjust System Info PIP and Switching Test Patterns Off • Press the number key corresponding to the function menu you wish to access, such as 2 for the Picture Quality menu. • Press or .
Installation All available channels are listed in the Channel Setup menu (Figure 3-18), which describes how each channel can be accessed and which serves as the gateway for editing, copying and deleting channels.
Installation 3. Select Locked from the Channel Setup menu and press ENTER to clear the check box. Channel Edit Name Number Input In Menu Auto Source Locked Previous Channel Next Channel 16x9 night 02 2 Sync Type: H-Sync: V-Sync: Interlace: Digital Encrypted 26.97 kHz 23.98 Hz No Y 1. 2. 3. 4. 5. 6. 7. 8. EL IM IN A R Clear this check box to unlock the channel Figure 3-19.
Installation Auto Setup also optimizes the following settings, based on the characteristics of the incoming signal: • Pixel Tracking • Pixel Phase • Size and Blanking • Height • Position • White Balance (Input Levels) Y If additional fine-tuning is necessary after performing an Auto Setup, continue with the next section.
Installation For 1080i digital and 1080p signals, channels are pre-configured at the Vidikron factory for each aspect ratio. These channels use Custom size presets to achieve the selected aspect ratio. • “Custom” Resizing: The “Custom” re-size descriptor automatically appears in the Size and Position menu when any of the values for Size, Height, Horizontal Shift, Vertical Shift or Blanking do not correspond to those for a preset. This option is not offered in the Size Presets pull-down list.
Installation Pixel Phase: Adjust pixel phase when the image (usually from an RGB source) still shows shimmer or “noise” after pixel tracking is optimized. Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. Note Adjust “Pixel Tracking” before “Pixel Phase.” EL IM IN A R Y For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image.
Installation Filter: The proper filter setting is automatically set for virtually all signals, and rarely needs to be changed. It applies a low pass filter for noise reduction in the incoming input signal, particularly for HDTV or SDTV. Applied in the analog domain before sampling, this filtering removes high frequencies and thus reduces pixel phase noise (note this also reduces signal bandwidth).
Installation • Pre-Calibration: Keep off for virtually all sources (default). Temporarily enter a check mark only if you are an experienced technician and you have an unusual source that you feel needs further color temperature and/or white balance adjustment. After entering a check mark, wait for the six slidebar values to stabilize, then clear the check mark and exit.
Installation • Clipping Detector: The Clipping Detector is a tool to assist with defining individual input levels, enabling you to accurately set the white balance for any particular source with the appropriate image. White Balance Pre Calibration Red Black Level Red White Level Green Black Level Green White Level Blue Black Level Blue White Level Auto Color Enable Clamping Clipping Detector Color Enable EL IM IN A R 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.
Installation 6. It may be advantageous to go back and check the black band. Adjust the blacklevel slidebar if necessary. Note 7. Readjusting the black levels affects the gain at this point; only readjust when absolutely necessary. Repeat Steps 4 through 6 with the other two remaining primary colors. When each primary color shows one optimized black band and white (or colored) band, the input levels for this source are correctly set.
Installation OptiCal (Primary Lens Calibration): OptiCal provides the ability to store and recall focus, zoom and position settings for the primary lens. To enable OptiCal: 1. 2. 3. 4. 5. 6. 7. 8. 9. Geometry and Color Test Patterns Grid Keystone 50 White Field Uniformity Edge Shading Color Gamut Adjust Color Levels Black Field Uniformity Default Color Adjustment ISF Night OptiCal 1. Select Installation from the Main Menu. 2. Select Geometry and Color from the Installation menu. 3.
Installation 3.13 Working With the Lamp Access the Lamp Adjust menu to: • Choose a lamp mode for regulating power and light output. • Change the optical aperture size. • View information pertaining to past and present lamps. • Record the lamp serial number in the projector’s memory. Y Lamp Hours (read-only): Lamp Hours shows the number of hours logged on the current lamp.
Installation Lamp Mode: Select the Lamp Mode you want to use in order to control the light output. You can choose to run the lamp as bright as possible, you can power the lamp with a specific wattage appropriate for the installed lamp or you can set a specific intensity (brightness) to maintain. Keep in mind that higher lamp power settings can shorten lamp life.
Installation For example, a 1000-Watt lamp can be driven at no more than 1000 Watts. To produce desired brightness at the screen, a new lamp would likely need less than this maximum rating — perhaps 812 Watts (example only). Over time, however, the lamp requires more and more current in order to generate the desired light, until eventually the lamp wattage reaches its 1000-Watt maximum and the lamp power automatically levels off.
Installation PR EL IM IN A R Y Notes: 62 Vision Model 140/150 Installation/Operation Manual
4 Press the MENU button on either the remote control or the VHD Controller front panel to display the Main Menu. Y To select a menu item, use the and buttons on either the remote control or the VHD Controller front panel to highlight it. Press ENTER to confirm your selection. PR EL IM IN A R The Vision 140/150 OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source and signal characteristics, some menu options may not be available.
Operation Picture Input Position ISF Presets Information (read-only) PR Test Video ISF Night - Input Image ISF Night - Input Color ISF Day - Display Color Note: Intelliwide 2.35 is available only on Vision 140/150 projectors equipped with the CineWide option (secondary anamorphic lens).
Operation The Main Menu is the starting point for accessing all projector functions. Main Menu (The Calibration and Service menus are hidden and not accessible until you enter a passcode.) Vidikron Video Input Source Aspect Ratio Picture Input Position ISF Presets Information Calibration EL IM IN A R Y Service From the Main Menu, select Input Source to choose a video signal source. The active source is indicated by an arrow (>) to its left; in this example, Composite is the active source.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key 16:9 16:9 Description Select 16:9 to view 16:9 DVDs and HDTV programs in their native aspect ratio. EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) 4:3 images are stretched horizontally to fit a 16:9 screen. 4:3 Image, stretched to fill 16:9 Screen (Display) 4:3 IntelliWide 4:3 Image on 16:9 Screen (Display) 4:3 scales the input signal to fit in the center of the 16:9 screen.
Operation Table 4-1. Aspect Ratio Settings (continued) Remote Control Key Cinema CINEMA Description Select Cinema to view 2.35 source material in its native aspect ratio. EL IM IN A R 2.35:1 Image on 16:9 Screen (Cinema aspect ratio / no CineWide) 2.35:1 Image on 2.35:1 Screen (Cinema aspect ratio / CineWide) Intelliwide 2.
Operation Picture ➤ Picture Use the controls in the Picture Menu to calibrate your Vision 140/150 for optimum picture quality. The Vision 140/150 has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF).
Operation Above Black EL IM IN A R Below Black Y Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2 shows a typical PLUGE pattern. Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.
Operation EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3. Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray Select Color and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. Figure 4-5.
Operation Overscan: Image Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area. Select from 1% to 10% of Overscan, as desired.
Operation Calibration ➤ Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only. Calibration ISF Night Note Display Color You must enter a passcode to access the Calibration menu. Input Image Input Color To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF Presets menu (see above).
Operation • Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources. Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image. ISF Day - Display Color: Refer to ISF Night - Display Color. ISF Day - Input Image: Refer to ISF Night - Input Image.
Operation Service ➤ Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only. Service Test Video Note Input Names You must enter a passcode to access the Service menu. Remote Control Display Device HD Format Test Video: Select Test Video from the Service Menu to access the internal test patterns on the Vision 140/150. Four patterns are available, consisting of white/gray or colored bars.
Operation When you change a remote code on the VHD Controller, you must re-program your remote control to send that same code. To do this: 1. Using a straightened paper clip or similar object, press and hold the CODE button on the remote control for approximately three seconds, or until the LED on the remote lights solid red.
Operation HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the VHD Controller to switch from HD to 480i signals or vice versa.
Operation System Reset: To reset ALL projector and controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu. A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel. Caution This action is not undoable.
Operation PR EL IM IN A R Y Notes: 80 Vision Model 140/150 Installation/Operation Manual
5 Maintenance and Troubleshooting The Vision 140/150 uses a Cermax® Xenon lamp to deliver its high brightness. The lamp should be replaced when it reaches the end of its life (typically 1000 hours), or sooner if a noticeable degradation in brightness occurs. When you replace a lamp, you should replace the filters as well. EL IM IN A R Y Keep track of the number of hours the lamp has been in use and be aware of any changes to brightness.
Maintenance and Troubleshooting Grasp the lamp by its housing only and pull it straight out (lamp slides along guides) until it’s free; see Figure 5-3. Discard the lamp using safe disposal/recycling practices or contact your Vidikron dealer for a possible re-lamping program. EL IM IN A R Y 4. Figure 5-3. Removing the Lamp PR 5. Align the new lamp with the top and bottom guides on the left side of the lamp compartment; see Figure 5-4. Slide the lamp all the way in.
Maintenance and Troubleshooting 13. Press ENTER to accept the change. This adds the new lamp serial number to the Lamp History menu and resets the Lamp Hours timer to “0.” Lamp Mode and Lamp Limit remain as they were for the previous lamp and can be changed at any time. Y EL IM IN A R 1. 2. 3. 4. 5. 6. 7. 8. 9. Lamp Adjust Lamp Hours 147 Lamp S/N 123456789 Lamp Message Lamp Limit 1000 Lamp Mode Power Power 500 Intensity 0 RVR 3 Lamp History Change Lamp Reserved Figure 5-5.
Maintenance and Troubleshooting 5.2 Lens Replacement If you need to remove the lens – either to replace it or to prepare the projector for shipment – proceed as follows: Power down the projector and wait five minutes to allow the lamp to cool. 2. Remove the secondary anamorphic lens, if present. 3. Place the lens cap on the installed lens to protect it from damage. 4. Press and hold the “lens release” button located in the top right corner of the lens panel. 5.
Maintenance and Troubleshooting Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 140/150. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Vidikron Technical Support. Table 5-1. Troubleshooting Chart Symptom • • • The projector and VHD Controller are both on, but there is no picture and on-screen menus do not appear.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Poor-quality or improperly connected source. • • The horizontal or vertical scan frequency of the input signal may be out of range for the projector. • Ensure that the source is properly connected and of adequate quality for detection. Correct at the source. • Contrast is set too high. • Lower the contrast setting.
Maintenance and Troubleshooting If the status code display on the back of the projector shows one of the following values, you have encountered a likely system error requiring the attention of a qualified service technician. Acknowledge and clear the error by pressing EXIT twice on the rear-panel keypad. Try resetting the projector by powering it off, allowing it to cool and powering it on again. Refer to Table 5-2 and contact your dealer if the problem persists.
Maintenance and Troubleshooting Table 5-2. Vision 140/150 Error Codes (continued) Code Description Power and Cooling Red DMD heat sink overheated. 47 Green DMD heat sink overheated. 48 Blue DMD heat sink overheated. 49 Prism overheated. 4C Projector shutdown due to critical error. C0 Lamp blower failure (lamp not turned on). EL IM IN A R Y 46 51 LVPS fan failed (Fan 1). 52 LVPS/Red cooling fan failed (Fan 2). 53 DC lamp fan failed (Vision 140; Fan 3).
Maintenance and Troubleshooting Table 5-2. Vision 140/150 Error Codes (continued) Code Description Boot code CRC failed. 61 Unable to program DigMux PLD. 62 Unable to program Control PLD. 63 Unable to program Bubks PLD. 64 Unrecognized ROM type. 65 Write to flash ROM failed. 66 TIPM failure. 67 Downloaded code will not fit. 68 Scaler communication problem. EL IM IN A R 60 Y TIPM (Image Processor) Built-In Keypad 70 Unable to access EEPROM on the built-in keypad.
Maintenance and Troubleshooting Table 5-2. Vision 140/150 Error Codes (continued) Code Description Miscellaneous A0 Unable to program the optional module. A1 Unable to power the optional module. A2 Unable to program the Dual Slot Backplane Module (DSBP). A3 Unable to program the optional Post Processing Module (Warp module). PR EL IM IN A R Y Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice.
Serial Communications 6 To interface the VHD Controller with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-14. 6.1 RS-232 Connection and Port Configuration Y Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the VHD Controller RS-232 port.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications PR EL IM IN A R Y Notes: 96 Vision Model 140/150 Installation/Operation Manual
7 7.1 Vision 140/150 Specifications Table 7-1 lists the Vision 140/150 specifications. Table 7-1. Vision 140/150 Specifications Projector Type: Digital Light Processing (DLP), 3-chip, 16:9 LightAmp™ DMD Native Resolution: 1920 x 1080 (16:9) Aspect Ratios: Refer to Table 7-2 Video Standards: Refer to Table 7-2 DTV Compatibility: 480p, 720p, 1080i, 1080p Scan Frequency: Horizontal: 15 kHz to 120 kHz Vertical: 23.
Specifications Table 7-1. Vision 140/150 Specifications (continued) Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications Brightness: 86.5 foot-Lamberts (fL) (Vision 140); 102.0 fL (Vision 150) Contrast Ratio (variable, based on lens aperture setting): 235:1 - 275:1 (Vision 140); 224:1 - 275:1 (Vision 150) These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.
Specifications 7.2 VHD Controller Specifications Table 7-2 lists the VHD Controller specifications. Table 7-2. VHD Controller Specifications Aspect Ratios: 4:3, Letterbox, 16:9, IntelliWide, Cinema, Intelliwide 2.
Specifications Figure 7-1 shows the Vision 140/150 dimensions (all dimensions are in inches). 25.9 22.9 0 28.8 24.1 14.1 5.6 0 3.9 6.9 25.9 Ø 8.8 13.4 12.4 10.1 6.4 13.4 25.6 28.9 2.6 3.9 24.1 25.5 28.8 14.1 19.8 9.4 9.5 6.9 3.9 6.0 0 0 .5 2.6 0 7.3 Vision 140/150 Dimensions 0 .6 6.7 25.9 Figure 7-1.
020-0833-01 Rev. A March 2008 1-888-4-VIDIKRON Fax 503-748-8161 www.vidikron.
