O W N E R ’ S O P E R A T I N G M A N U A L VL-52 and VL-57 1080p HIGH-DEFINITION LCD FLAT PANEL DISPLAYS
ONE YEAR LIMITED WARRANTY For LCD Displays Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents.
RIGHTS, LIMITS AND EXCLUSIONS: Vidikron limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Vidikron also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages.
ADDITIONAL INFORMATION: To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited Warranty, please call or write: EL IM IN A R Y VIDIKRON Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-5900 Fax: (510) 324-5905 Toll Free: (888) 4VIDIKRON VIDIKRON PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS ________________________________________ Model Purchased Date PR ___________________
Important Safety Instructions Thank you for your purchase of this quality Vidikron product! For best performance, please read this manual carefully as it is your guide through the menus and operation. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Compliance Information DECLARATION OF CONFORMITY: Manufacturer’s Name: Vidikron, a subsidiary of Planar Systems, Inc.
FCC PART 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1 ONE YEAR LIMITED WARRANTY .............................................................................................. iii Important Safety Instructions ................................................................................................. vi Compliance Information ......................................................................................................... vii 1. Introduction .....................................................................................
Table of Contents 4. Operation .......................................................................................................................... 23 Turning on the Power ....................................................................................................................................23 Changing the OSD Language .....................................................................................................................23 Setting the PC Display Properties ..................
1 List of Figures 2-1. DView Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2-2. DView Rear-Panel Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2-3. DView Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3-1. Antenna/Cable TV Connection .
List of Figures PR EL IM IN A R Y Notes: xii Vidikron VL-52 and VL-57 Owner’s Operating Manual
1 Introduction 1.1 About This Manual Vidikron has prepared this manual to help home theater installers and end users get the most out of the DView. Target Audience Y This Owner’s Manual describes how to install, set up and operate the Vidikron DView™ VL-52/VL-57 Flat-Panel LCDs. Throughout this manual, the Vidikron DView™ VL-52/VL-57 Flat-Panel LCDs are referred to simply as the “DView.” EL IM IN A R Vidikron has made every effort to ensure that this manual is accurate as of the date it was printed.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: TIPS highlight time-saving short cuts and helpful guidelines for using certain features. Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.
Introduction Vidikron presents the DView™ VL-52/VL-57 Flat-Panel LCDs, perfect for those who demand our award-winning flat panel performance along with advanced LCD technology and lightweight design. 1.3 Description, Features and Benefits The DView incorporates the superb Imagix™ digital video processing that produces outstanding picture quality with a wide range of both standard and high definition source material.
Introduction Parts List ➤ Your DView is shipped with the following items. If any items are missing or damaged, please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON.
Controls and Functions 2 2.1 DView at a Glance Figure 2-1 shows the locations of the DView controls and indicators. EL IM IN A R Right Side Y Controls and Indicators TV/AV 1 MENU 2 + VOL 3 – PR CH 4 5 7 6 Figure 2-1. DView Controls and Indicators 1. TV/AV Button (Input Source Selection) To select a source, press the TV/AV button (with no menus visible on-screen). Use the CH or CH button (see below) to highlight the desired input source and press TV/AV again.
Controls and Functions 4. CH / CH Use these buttons to scroll through available TV channels (VL-52 only). When a menu is visible on-screen, these buttons operate identically to the up- and down-arrow ( and ) buttons on the DView remote control unit. 6. Remote Control Sensor 7. Status Indicator LED - Lights red to indicate that the DView is in standby mode; - Lights green during power-on sequence and during normal operation; - Flashes green when the DView receives a signal from the remote control.
Controls and Functions INPUT2 S-Video Input Standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR. 4. Headphone Jack 5. Main Power Switch 6. Power Input (100 to 240 VAC) Connect the DView to power here. 7. RGB A 15-pin VGA connection to a personal computer. The DView automatically detects the signal resolution. 8. HDMI1/Computer Input (Digital) 9. HDMI2/Computer Input (Digital) EL IM IN A R Y 3.
Controls and Functions 24. AIR (Antenna) Input (VL-52 only) 75-ohm coaxial input for connecting a TV antenna to the digital TV input. 25. CABLE Input (VL-52 only) 75-ohm coaxial input for connecting a CATV system to the digital TV input. 26. RS-232 CONTROL PORT A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system. 27. SPEAKER OUTPUT (RIGHT) 28. SPEAKER OUTPUT (LEFT) PR EL IM IN A R Y For connection of the right (27) left (28) speakers.
Controls and Functions Figure 2-3 shows the DView remote control, and the paragraphs that follow describe its functionality. ON 1 2 3 4 5 6 7 8 2 9 0 – TV SOURCE INPUT 1 INPUT 2 INPUT 3 3 HDMI1 MEMORY ISF NT ISF DAY ASPECT RATIO 5 ANA LET BOX 4X3 7 MENU ASPECT ENTER CH 4 I-WIDE PR CH VOL - INPUT 4 RGB HD HDMI2 CUST Y OFF EL IM IN A R 1 VOL + EXIT 6 8 SIZE POSITION PIP S.SWAP SWAP TV/AV S.
Controls and Functions 1. OFF / ON Use these buttons to turn the DView on or off. 2. Numeric Buttons Use these buttons to enter menu pass codes. VL-52 only: Use the numeric buttons to enter TV channel numbers. Use the TV button to switch to the Antenna/DTV/CATV input. Use the - button to enter DTV sub-channel numbers. Source Selection Buttons INPUT 1 Press this button to switch to Input 1. EL IM IN A R INPUT 2 Press this button to switch to Input 2. Y 3.
Controls and Functions 5. Aspect Ratio Selection Buttons ANA (16:9 Anamorphic) For 16:9 DVDs or HDTV program material. 4X3 (Standard 4:3) The input signal is scaled to fit 4:3 display mode in the center of the screen. LETBOX (Letterbox) Image in letterbox format is enlarged to fit 16:9, full-screen display and the upper/lower portions are “blanked off.” Arrow Buttons ( , , , ) Use these buttons to change TV channels (VL-52 only), select items or settings, adjust settings or adjust sound volume.
Controls and Functions 10. TIMER OFF Button Press this button to set the sleep timer. Press it repeatedly to scroll through the available options (Off, 10, 30, 60, 120 or 180 minutes). 11. Sound Control Buttons S.MODE Press this button repeatedly to scroll through the available Equalizer presets (CUSTOM, STANDARD, MUSIC, FILM or SPEECH). Y SURRND (Surround) Press this button to turn Surround Mode on or off.
3 Installation 3.1 Remote Control To install batteries in the remote control: Slide the battery cover in the direction of the arrow and remove it. 2. Insert the included batteries. Ensure that the polarities correctly match the markings inside the battery compartment. 3. Slide the battery cover back on until it snaps into place. and EL IM IN A R 1. Y Battery Installation 1. Do not mix an old battery with a new one or different types of batteries. Note 2.
Installation 3.2 Quick Setup Table 3-1 gives a quick overview of the DView installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. Y Table 3-1. Installation Overview PR For Details, refer to page...
Installation Proper installation of your DView will ensure the highest possible picture quality. Whether you are installing the DView temporarily or permanently, you should take the following into account to ensure that it performs optimally. You can either place the DView on a table or in an entertainment center, or mount it on a wall. 3.3 Installation Considerations Wall-Mounting the DView Vidikron recommends that this be done by a custom installation specialist.
Installation 3.4 Connections to the DView Proceed as follows to connect the DView to your video sources, external controller(s) – if present – and AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. • Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connect your video sources to the DView as shown and described in the sections that follow.
Installation HDMI Connections: The DView has two HDMI inputs for connecting a BD/HD-DVD/DVD player, DTV decoder, personal computer or any other device with an HDMI or DVI output. Connect such devices as shown in Figure 3-2. Tip This DView supports the VESA Display Data Channel (DDC) standard. This standard provides “Plug and Play” capability; the display and a VESA DDC-compatible computer communicate their setting requirements, allowing for quick and easy setup.
Installation RGB Connections: The DView has an RGB input for connecting a personal computer; see Figure 3-3. Rear of the Display Rear of the PC INPU INPUT3 Y Audio Cable (Sold Separately) EL IM IN A R D-Sub 15 Pin Cable (Sold Separately) Figure 3-3. Analog RGB Connections Note 1. Refer to Computer Signal Compatibility on page 61 for a list of computer signals compatible with the DView. Use with signals other than those listed may cause some functions not to work. 2.
Installation Component Video Connections: If you have a DVD player or DTV decoder with a component (YPbPr) output, connect it to INPUT 3 or INPUT 4 of the DView as shown in Figure 3-4. INPUT4 Y INPUT3 EL IM IN A R Audio Cable DVD/DTV STB Video Cable Figure 3-4. Component Video Connections Composite/S-Video Connections: The DView has two (2) S-Video and four (4) composite video inputs for connecting a VCR, camcorder, laser disc player or DVD player; see Figure 3-5.
Installation AV OUT Connection ➤ The DView has stereo audio and Composite video outputs for connecting to a second VCR or other auxiliary equipment. Connect the AV OUT audio and video jacks to the audio and video inputs of the VCR or other equipment as shown in Figure 3-6. You can route either the main or picture-in-picture (PIP) source signal to the AV output. For more information, refer to Monitor Out on page 38. The audio output level is fixed.
Installation Connect the (positive) and (negative) speaker wires to the rear-panel SPEAKER-R and SPEAKER-L terminals; see Figure 3-8. Maintain the correct polarity. For more information, refer to the owner’s manual for your speakers. Twist exposed wire strands together. Right Speaker Left Speaker EL IM IN A R Push tab to the open position, and insert the wire. Then, close tab firmly to secure the wire in place. Y m 12 m Connecting External Speakers (Optional) Figure 3-8.
Installation RS-232 Controller ➤ Connection Use a straight-through RS-232 cable with a 9-pin male connector to connect a PC or home theater control/automation system (if present) to the RS-232 port on the DView; see Figure 3-10. For more information about using this connection, refer to Serial Communications on page 51.
4 Turn on your source components. 2. Plug the female end of the supplied power cord into the AC receptacle on the rear of the DView (AC 100V ~ 240V). See Figure 2-2. 3. Connect the other end to your AC power source. 4. Turn on the main power switch at the rear of the display. The power indicator lights red to indicate that the DView is in “standby” mode. 5. Press the ON button on the remote control to turn on the display (or press the power button on the side of the display).
Operation 4.3 Setting the PC Display Properties To maximize image quality when using the DView with a personal computer, you may need to adjust the display properties of your PC video card. To do this: Choose Settings from the Windows Start menu and click on “Control Panel.” EL IM IN A R Y 1. Double click on the Display icon. 3. Click the Settings tab on the display dialog box. 4. Set the Screen area to 1920x1080 pixels. 5. Click the Advanced button and click the Monitor tab on the dialog box.
Operation Note 1. The maximum available resolution and vertical frequency is 1920x1080/60Hz or the maximum supported by your video card, whichever is lower. You can get the best picture at 1920x1080/60Hz. 2. The DView supports 24-bit color (16,777,216 possible colors). To use the on-screen menus: 1. Press MENU to display the Main Menu. 2. To select a menu item, use the up- or down-arrow buttons ( control to highlight it. 3. Press ENTER or the right-arrow button ( ) to access that menu. 4.
Operation Picture Adjust Color Temp. Gamma Save Settings Restore Settings Balance Equalizer Audio Channel (VL-52 only) Digital (VL-52 only) Analog 0, 1, 2, 3 ... 100 Surround Audio Language (VL-52 only) Digital Audio Out TV Speaker Audio Delay Auto Tuning PR Add/Erase Favorite Channel Time On Timer Timer (VL-52 only) PC Mode Adjust Off Timer Sleep Timer Time Zone Daylight Saving English, Français, Español, Português or Deutsch Auto Adjust Clock Phase H. Position V.
Operation The Main Menu is the starting point for accessing all DView functions. Main Menu (The ISF Calibration menu is not accessible until you enter a passcode.) VL-52 Source Aspect Ratio Picture Adjust Audio Channel Timer Setup EL IM IN A R From the Main Menu, select Source to choose a video signal source. Y ISF Calibration The active source is indicated by an arrow (>) to its left; in the example at right, TV is the active source.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key 16:9 ANA Description EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) Select 16:9 to view 16:9 DVDs and HDTV programs in their native aspect ratio. 4:3 images are stretched horizontally to fit a 16:9 display.
Operation Use the controls in the Picture Adjust menu to calibrate your DView for optimum picture quality. Picture Adjust Picture Adjust The DView has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF).
Operation PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes. Select Brightness from the Picture Adjust menu. Using the left- and right-arrow ( buttons, adjust the brightness so that: ) • The darkest black bars disappear into the background. • The dark gray areas are barely visible. • The lighter gray areas are clearly visible.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4. Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint blue red magenta green cyan PR yellow gray Select Color from the Picture Adjust menu.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture Adjust menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and different sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. PR Figure 4-5.
Operation Each color temperature setting has six (6) “white balance” parameters associated with it (two each for red, green and blue). These are described later in this section; refer to White Balance on page 41. Gamma: The Gamma control determines how gray shades are displayed between minimum input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays.
Operation Audio Language (VL-52 only): Some digital TV broadcasts provide audio soundtracks in multiple languages. If you are watching such a program, select Audio Language from the Audio menu to choose a soundtrack language: English, Français, Español or Português. Digital Audio Out: The DView can output either two or six channels of digital audio. Select Dolby Digital if your A/V receiver can decode a Dolby Digital-encoded, 5.1-channel bitstream.
Operation To set the DView’s internal clock or configure the on/off timers, select Timer from the Main Menu and press ENTER. Timer (VL-52 only) Timer Time: To set the DView internal clock, select Time from the Timer menu and press ENTER. Then, do either of the following: Time • To synchronize the internal clock with time codes sent by the local Public Broadcasting Service (PBS) member station, select Auto Setup.
Operation Setup ➤ Use the controls in the Setup menu to perform advanced image quality adjustments and access various other DView features. Setup OSD Language: Select OSD Language from the Setup menu and press ENTER. Then, use the up- or down-arrow buttons to select the OSD language (English, French, Spanish, Portuguese or German). Press ENTER again to confirm your selection.
Operation • CC On Mute: To have the DView show captions when the audio output is muted, set this option to Yes. • Digital Font Option (VL-52 only): Select Digital Font Option (VL-52 only) from the Caption menu to customize the appearance of closed captions in digital TV broadcasts. • Control: Select Program to view the closed captions as presented by the broadcaster. Or, select User to override the program’s closed caption formatting.
Operation • Movie Rating: Select Movie Rating from the Parental Control menu to block movies carrying a given rating, to prevent children from watching movies that are deemed inappropriate. These ratings have been established by the Motion Picture Association of America (MPAA) to help parents and other caregivers determine if a movie is suitable for young viewers. To block movies carrying a given rating, press the right-arrow button to require the PIN code to be entered to view a movie with that rating.
Operation Overscan (not available with PC signals): Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Overscan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.
Operation ISF Calibration ➤ Use the ISF Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only. ISF Calibration Picture Adjust White Balance Note You must enter a passcode to access the ISF Calibration menu. Blue Enable Baud Rate Factory Reset Picture Adjust: The controls in this menu are identical to those in the main Picture Adjust menu, but are accessible only by entering the ISF Calibration menu passcode.
Operation • Save Settings: For each input and supported resolution, the DView lets you save image quality settings as presets that you can recall at a later time. You can create up to three presets – designated “Custom,” “ISF Day” and “ISF Night” – per input and resolution.
Operation Splash Duration: Use Splash Duration to control how long the DView splash screen remains on-screen after power-up; see Figure 4-6. To prevent this screen from appearing, set the Splash Duration to 0. EL IM IN A R Y CALIBRATED FOR: PR Figure 4-6.
Operation To use PIP, press the PIP ( ) button. ASPECT SIZE POSITION PIP S.SWAP SWAP TV/AV TIMER OFF EL IM IN A R Y The PIP window appears inside the main image window. 2. Press the ( Press PIP again to switch to side-by-side PIP mode. PR Press PIP again to turn PIP off. Vidikron VL-52 and VL-57 Owner’s Operating Manual 43 4.
Operation Press the TV/AV button ( ) to select a PIP signal source. For each source, Table 4-3 shows which of the other sources are available as a PIP source. Table 4-3. Available Main and PIP Source Combinations PIP Input Source INPUT3 INPUT4 INPUT INPUT 1 2 VIDEO COMP VIDEO COMP COMP. VIDEO COMP.
Operation To change the PIP window position, press the POSITION ( ) button on the remote control repeatedly until the window is in the desired position. ASPECT SIZE POSITION PIP S.SWAP SWAP TV/AV Changing the PIP Position 3 2 4 1 EL IM IN A R To change the PIP window size, press the SIZE ( ) button on the remote control repeatedly to achieve the desired window size. Y TIMER OFF ASPECT SIZE POSITION PIP S.SWAP SWAP TV/AV SIZE POSITION PIP S.
Operation Swapping the Main and PIP ➤ Images To swap the main and PIP images, press the SWAP button on the remote control. ASPECT SIZE POSITION PIP S.SWAP SWAP TV/AV SIZE POSITION PIP S.SWAP SWAP TV/AV EL IM IN A R Y TIMER OFF To swap the main and PIP audio programs, press the S.SWAP button on the remote control.
Operation The DView supports Multichannel Television Sound (MTS), the broadcast audio standard that allows transmission of both stereo and Secondary Audio Program (SAP) content. The SAP is usually a foreign-language translation. However, it can also be used for other purposes such as Described Video Services (DVS), which provide descriptive narration of key visual elements in programs for the benefit of the visually impaired.
Operation PR EL IM IN A R Y Notes: 48 Vidikron VL-52 and VL-57 Owner’s Operating Manual
5 Maintenance and Troubleshooting Regular cleaning will extend the life and performance of the DView. Before cleaning, be sure to unplug the power cord from the power outlet. Do not under any circumstances use solvents such as benzene or thinner to clean the DView. Doing so may cause deterioration or peeling of paint from the display or remote control unit. 5.1 Cleaning Cleaning the Display Panel Body and Remote Control EL IM IN A R Y Wipe the display and remote control gently with a soft cloth.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Picture is okay, but there is no sound. Solution • Audio output is muted. • • • Volume setting is too low. Source component is connected incorrectly or not at all. Speakers are connected incorrectly or not at all. Audio settings are incorrect. • • • • EL IM IN A R Y • • Check speaker connections (Figure 3-8).
Serial Communications 6 To interface the DView with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-10. (Use a straight-through cable.) 6.1 RS-232 Connection and Port Configuration Y Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to match that of the DView RS-232 port.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications Table 6-1.
Serial Communications PR EL IM IN A R Y Notes: 56 Vidikron VL-52 and VL-57 Owner’s Operating Manual
7 7.1 DView Specifications Table 7-1 lists the DView specifications. Screen Size: VL-52 = 52 in. (diagonal) VL-57 = 57 in.
Specifications Table 7-1. DView Specifications (continued) Weight (including stand): VL-52 = 89.5 lbs. (40.60 kg) VL-57 = 118.0 lbs. (53.52 kg) Regulatory Approvals: Complies with FCC, CE, C-Tick, NRTL, GOST, MIC, SABS, RoHS, China RoHS Limited Warranty: One (1) year parts and labor from the date of delivery to the end user. PR EL IM IN A R Y Specifications are subject to change without notice.
Specifications EL IM IN A R 49.84 45.35 Y Figure 7-1 and Figure 7-2 show the DView dimensions (all dimensions are in inches). 25.51 3.72 30.00 33.72 Wall Mount Screw 6 x M8 Tap PR 4.51 9.84 23.62 7.87 7.87 5.55 Figure 7-1. VL-52 Dimensions Vidikron VL-52 and VL-57 Owner’s Operating Manual 59 7.
Specifications EL IM IN A R Y 53.70 49.21 27.64 3.72 32.13 35.85 4.51 9.84 PR Wall Mount Screw 6 x M8 Tap 23.62 7.87 7.87 6.61 Figure 7-2.
Specifications The DView can display video signals from a variety of computer sources via its RGB-HD and HDMI inputs. Table 7-2 lists the signal types that are compatible with the DView, and indicates which of those are VESA standards. Table 7-2. Computer/Video Signal Compatibility Chart Signal Type Mode Vertical Frequency (Hz) Horizontal Frequency (kHz) RGB HDMI 640x350 85 85.00 31.28 √ – VESA 640x400 85 85.00 35.
Specifications PR EL IM IN A R Y Notes: 62 Vidikron VL-52 and VL-57 Owner’s Operating Manual
020-0714-00 Rev. A October 2007 Vidikron 2900 Faber Street Union City, CA 94587 510-324-5900 Fax 510-324-5905 1-888-4-VIDIKRON www.vidikron.
