9”/ 20.1” / 22”WIDE SCREEN TFT-LCD MONITOR V193/ V220 Series V202 Series USER MANUAL www.viewera.com Rev. 2.
Table of Contents EMC Compliance …………………..……………………………………………………….……....1 Important Precautions ............................................................................................................2 1. Package contents .……………………………………………………………………..……….3 2. Installation……………………………………………………………………………………….3 2.1 Rear panel……………………............................................................................................3 2.2 Installation…………………………………………….....................................................
EMC COMPLIANCE This device has been tested and found to comply with the standards for a class B digital device, pursuant to Part 15 of FCC Rules. Those standards are designed to provide reasonable protection against harmful interference in a residential installation. This device generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT PRECAUTIONS 1. Before using this device, please read all the instructions in this manual carefully. 2. Please keep the manual carefully for future reference. 3. Unplug this device from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp or wet cloth to clean. Please use LCD screen detergent for cleaning if it is still dirty. 4. Do not use the parts not recommended by the manufacturer, otherwise it may cause a hazard. 5.
1. Package Contents Unpack the package and check you have the following items. TFT-LCD monitor (19 inch for V193 series, 20.1 inch for V202 series, 22 inch for V220 series) VGA signal cable Power cord User manual DVI signal cable Audio cable If any of the items is missing, please contact with your dealer at which you purchased the monitor. 2. Installation 2.1 Rear Panel 2.1.1 V193 and V220 series 2.1.2 V202 series 1. Power supply: AC 100-240 V, 60/50 Hz. 2.
2.2 Installation The monitor is equipped with an automatic sensing AC power adapter for a voltage range from 100 to 240 VAC at a frequency of 50 to 60 Hz. Before connecting the cables, please make sure that the monitor and the computer power are both turned off. Please follow the steps to install your monitor. Before connecting cables to the V193 or V220 monitor, you need to remove the plastic cover on the back of the monitor at first. 2.2.
2.2.4 Installing the monitor base 1. Take the monitor and the base out of the box and place its side on the table. 2. 1 For V193 and V220 series, align the three bolt holes on the monitor base with the three bolt hoes on the monitor arm, and then screw the threes bolts with a screwdriver. 2.2 For V202 series (1) After taking the monitor out of the carton, carefully turn the monitor screen face down.
2.3 Resolution setup For the best display quality, please set the monitor type in Windows. Control Panel > Display > Settings > Advanced > List All Modes (a) For V193 series, please set resolution to “ 1440 x 900 @ 60 Hz” . (b) For V202 and V220 series, please set resolution to “ 1680 × 1050 @ 60 Hz” . Note 1. To avoid picture stretching, you need to select the resolution of 16:10 aspect ratio, like 1680 x 1050, or approximate to 16:10, like 15:9 (i.e. 1280 x 768).
3. Control Functions 3.1 User Controls The monitor digital control functions are located on the front panel. They are shown in the figure below and described in the following paragraphs. (a) V193 and V220 series 5 4 3 2 1 (b) V202 series 54132 1. Power switch with LED indicator key: It is used to turn on or off the monitor. When the monitor is turned on, the LED is lit up in green (or blue). When the monitor is in power saving mode, the LED will turn red and flashing. 2.
3.2 OSD menu a. OSD menu with VGA connection b. OSD menu with DVI connection 1. Auto Adjustment: Adjust geometry of the picture automatically. (for VGA mode only) 2. Brightness: Adjust the brightness level of the picture. 3. Contrast: Adjust the difference in luminance between light and dark areas of the picture. 4. H. Position: Adjust the horizontal position of the picture. 5. V. Position: Adjust the vertical position of the picture. 6. Clock: Adjust the frequency of the signal. 7.
4. Specifications Specifications are subject to change without notice. For the latest specification information, please refer to ViewEra’ s product page on the website. Model V193 Series Features Panel Type: Active TFT-LCD Size: 19" diagonal Pixel Pitch: 0.2835 (W) × 0.2835 (H) mm Brightness: 300 cd/ m2 (typical) Contrast Ratio: 800:1 (typical) Response Time: 5 ms (on/ off, typical) Viewing Angle(H / V) 160°/160° (typical) Max. Resolution: 1440 (W) x 900 (H) Display Color 16.
Model V202 Series Features Panel Type: Active TFT-LCD Size: 20.1" diagonal Pixel Pitch: 0.258 (W) × 0.258 (H) mm Brightness: 300 cd/ m2 (typical) Contrast Ratio: 1000:1 (typical) Response Time: 8 ms (gray to gray, typical), 16 ms (on/ off, typical) Viewing Angle(H / V) 178°/178° (typical) Max. Resolution: 1680 (W) x 1050 (H) Display Color 16.
Model V220 Series Features Panel Type: Active TFT-LCD Size: 22" diagonal Pixel Pitch: 0.282 (W) × 0.282(H) mm Brightness: 300 cd/ m2 (typical) Contrast Ratio: 800:1 (typical) Response Time: 5 ms (gray to gray, typical) Viewing Angle(H / V) 160°/160° (typical) Max. Resolution: 1680 (W) x 1050 (H) Display Color 16.
5. Dead Pixel Policy Dead pixels on the TFT LCD panel are sometimes inevitable. The replacement policy varies with different models. Please refer to the product specification on ViewEra’ s website. 6. Warranty & Customer Service a. Warranty ViewEra warrants the V193, V202 and V220 series TFT-LCD monitors for 1 year on LCD panel, parts and labor. For detailed information, please refer to our website. (http:// www.viewera.com/warranty.htm) b.
8. Troubleshooting 1) No image Check if the power cord、the monitor and the power plug are well connected. Check if the monitor is off, please contact support@viewera.com for assistance. 2) “No Input Signal”appears. Check if the VGA cable is tightly connected between the video output connector on the video card and the video input connector on the monitor. Check if your video card driver is correctly installed. If possible, please re-install or update your video card driver.
