VFD725w-50P Digital Photo Frame - User Guide - ٺҢЙы Model No.
Compliance Information ViewSonic i English Following information is only for EU-member states: The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 8. 9. 10. 13. 14. 16. 17. 18. 19. 20. Do not use the equipment near water. Wipe the machine with a soft and dry cloth. Do not block any vent holes. Please install the product in accordance with the manufacturer’s instructions. Do not use the product on your legs for a long time because it gets hot and you may be burned.
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.
Copyright Information Copyright© ViewSonic Corporation, 2008. All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
TABLE OF CONTENTS Introduction............................................................................................................................................................. 1 Important Safety Precautions................................................................................................................................ 2 Overview...........................................................................................................................................................
Introduction Thank you for purchasing this Digital Photo Frame. This Digital Photo Frame is compatible with SD, MMC, MS and CF memory card formats, which enables you to view digital photo directly from your camera’s memory card. This manual contains important safety information and operation instructions, so please read all the instructions carefully before using the Digital Photo Frame and keeps it for future reference.
Important Safety Precautions Always follow these basic safety precautions when using your Digital Photo Frame. This will reduce the risk of fire, electric shock, product damage and personal injury. y Warning: Do not remove the cover or back to reduce the risk of electric shock. There are no user-serviceable parts inside. Refer servicing to qualified personnel. y Warning: Do not expose the Digital Photo Frame to rain or moisture to prevent fire or electric shock hazard.
Cleaning y Before cleaning the Digital Photo Frame make sure it is turned off. y Never spray or pour liquid directly onto the screen or plastic casing. y To clean the LCD screen, wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles. If it is still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner on a clean, soft, lint-free cloth to clean the screen. y To clean the plastic casing, use a soft, dry cloth.
Main Features y 7 inch Digital TFT LCD: 800*480 15:9 y Decorative appearance, good quality y Displays digital pictures (JPEG) without a computer y Automatic slide show with multiple transition effects y Compatible with SD/MMC/MS, and CF memory cards y USB Host for connecting to the USB mass storage y USB2.
Overview Front View Back and Side View 1. [X] Play/Pause; Confirm touch key 5. [h] Right/Rotate touch key 10. USB HOST 2. [M] Menu touch key; touch and hold to 6. [i] Up/Previous touch key 11. Mini-USB connection open OSD menu 7. [j] Down/Next touch key 12. 9V DC Input socket 3. [2] Exit touch key 8. SD/MMC/MS-card slot 13. Adjustable mounting 4. [g] Left/Rotate touch key 9. CF-card slot 14.
Getting Started Attaching the mount 1. Place the frame on a flat surface with its back facing you. 2. Place the mount carefully in the slot on the back of the frame. 3. Turn the mount counter-clockwise by 45°until it locks. It will now be possible to set the device in the landscape orientation. 4. Turn the mount counter-clockwise by 90° until it locks. It will now be possible to set the device in the portrait orientation 5.
Connecting to the power 1. Plug one end of the power adaptor into the DC socket in the Digital Photo Frame, and the other into the wall outlet. 2. Switching the power to the ON marking position to turn on the Digital Photo Frame. Note: y To turn off the Digital Photo Frame completely, slide the power switch from ON to OFF. Inserting Media In order to play images from a card or a memory stick, insert the card into its respective card slot on the Digital Photo Frame or use the USB port.
1. 3. Insert the SD/MMC/MS card into the 3-in-1 card slot Push a USB memory stick into the USB HOST slot. with the metallic contacts facing towards the display. 2. Insert the CF card into the CF card slot with the pinholes pointing towards the photo frame. Note: y Do not use any force while inserting a memory card or attaching a memory stick. y The 3-in-1 card slot only reads one memory card at a time. Do not insert more than one card into one memory card slot.
Copy files from computer You can connect the digital photo frame to a computer to copy the files to the built-in memory (depends on the unit you purchase) or the card inserted on the photo frame. 1. Make sure that your computer has been started before you start. 2. Connect the mini plug of the USB cable to the mini USB port on digital photo frame, and push the other end into a free USB port on your computer. 3. The computer system detects “New hardware” and starts to install the driver automatically.
Viewing Photos Main screen y Once you switch on the digital photo frame, the main screen appears. When a memory device is inserted into the Digital Photo Frame, the corresponding icon appears on the main screen. y In the main screen, you can select connected source to view pictures, change frame settings, or display the calendar. 1. Touch the [M] button to access the main screen. All connected source, setup and calendar icons are displayed. USB driver Appears when you inserted a USB flash driver.
2. Touch the [g] or [h] button to select a memory source, and then touch the [X] button. The mode menu appears. Use the [g] or [h] button to select Photo, or File. Viewing thumbnails In Photo mode, the pictures on the selected memory source can be displayed on the screen as thumbnails. Up to 15 pictures are displayed at a time. 1. Select a memory source (e.g. USB, SD/MMC) in the main screen and touch the [X] button. The mode menu appears. 2.
Browsing a single picture You can select a single picture to display on the screen: 1. Select a picture in the thumbnail view, and touch the [X] button. The selected picture is displayed on the full screen. y To view the previous or next photo, touch the [i] or [j] button. y To rotate a picture, touch the [g] or [h] button. There will pop out a window on the screen: 2. To return to the thumbnail view, touch the [2] button. 3. To start slide show from the current picture, touch the [X] button.
Using OSD menu You also can use the OSD menu to manually view the photos one by one. 1. Touch and hold the [M] button during viewing the picture or slideshow. The OSD menu appears on the screen and slideshow pauses. 2. Touch the [g] or [h] button to navigate between the icons on the OSD menu. y To start or resume slide show from the current picture, highlight X and touch the [X] button.
Managing Files In the File mode, you can view all playable files and folders on the memory source. You also can copy files from a memory device to another memory device or delete the files. 1. Select a memory source (e.g. USB, SD/MMC) in the main screen and touch the [X] button. The mode menu appears. 2. Touch the [g] or [h] button to select File, and touch the [X] button. The file list appears. 3. Use the [i] or [j] button to navigate between files and folders.
Coping files 1. Highlight a file using the [i] or [j] button and touch the [h] button. A check mark ; is displayed next to the file. To check more files, repeat above step. 2. Touch and hold the [M] button. A menu with COPY and DELETE options displays on the right screen. 3. Use the [i] or [j] button to select COPY and touch the [X] button. The other available memory source is displayed. 4. Use the [i] or [j] button to select a memory device and touch the [h] button to select the destined directory.
Changing Frame Settings The system settings let you customize and configure your Digital Photo Frame 1. Select the SETUP icon in the main screen and touch the [X] button. 2. To select a setting option, touch the [i] or [j] button. The Setup Menu and software version appear on the screen. 3. To change the value, touch the [g] or [h] button and then touch the [X] button to confirm. 4. Touch the [2] button to exit.
Display Mode Key-light Timeout TFT Brightness TFT Contrast TFT Saturation Default settings ViewSonic Set the screen display mode. The available options include: Fit Screen, Full Screen Set the backlight exiting time for touch keys. The available options include: 5s, 10s, 20s Adjust the brightness of TFT screen. The available options include: -3, -2, -1, 0, 1, 2, 3. Adjust the contrast of TFT screen. The available options include: -3, -2, -1, 0, 1, 2, 3. Adjust the saturation of TFT screen.
Frequently Asked Questions 1. Why cannot the Digital Photo Frame display some files from my Flash card or USB device? • Some unpopular memory cards are not compatible with the device. Use a card which matches with the Digital Photo • The file formats on your card or USB device might not be supported (only JPEG pictures are accessible). Provide files Frame. with the supported JPEG. 2. There is a memory card inserted in the Digital Photo Frame, but the device is not able to read the card.
3. Why do some pictures load faster than others? • Higher resolution pictures load slower. Use pictures with lower resolution to speed up the loading time. Note: The Digital Photo Frame supports up to 8000*8000 pixels picture display. 4. Why does the screen not show anything? • The device might not have been turned ON or the adapter is not well connected. 5. Can I rotate a picture on the screen? • YES. Use the [g] or [h] button to rotate a picture.
Specification Digital TFT LCD Panel size: 7 inches Display Screen aspect ratio: 15:9 Resolution: 800*480 pixels I/O DC in Power adaptor Input: 100~240V AC, 50~60Hz Output: DC 9V 1.5A USB port USB Host 2.0 & USB device 2.0 Supports USB flash media Supported devices peripheral SD™ (Secure Digital Card), MMC™ (MultiMedia Card), MS™ (Memory Stick), CF™ (Compact Flash) Supported photo format JPEG, Maximum resolution: 8000*8000 pixels Operating temperature -10ć ~ 40ć Dimension 210*160*28.
Customer Support For technical support or product service, see the table below or contact your reseller. Note: You will need the product serial number. Country/Region Web Site Telephone Taiwan http://www.viewsonic.com.tw/ 0800-061-198 Singapore http://www.viewsonic.com.
Limited Warranty VIEWSONIC Digital Photo Frame What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
