LS800WU/LS800HD DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, RU RWKHU GHYLFHV LQFOXGLQJ DPSOL¿HUV WKDW SURGXFH KHDW 9.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Copyright Information Copyright © ViewSonic® Corporation, 2018. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Important safety instructions .......................2 Operating in a high altitude environment ....................................... 42 Using the CEC function..................... 43 Using the 3D functions ...................... 43 Using the projector in standby mode . 44 Adjusting the sound ........................... 44 RJ45 ................................................... 45 Preparing Email Alerts ...................... 50 RS232 by Telnet Function .................
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
12. 13. 14. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call your local service center to have the projector serviced.
Laser warning This symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed. Class 3R laser product This Laser Product is designated as Class 3R during all procedures of operation. LASER LIGHT - AVOID DIRECT EYE EXPOSURE. Do not point laser or allow laser light to be directed or reflected toward other people or reflective objects. Direct or scattered light can be hazardous to eyes and skin.
Product labels Below drawing show the label’s location. 11 12 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT Emitted wavelength : 450-460 nm Max. Pulse energy: 0.698 mJ, Pulse duration: 1.
Location of laser aperture Below drawing is the laser aperture location. Be careful not to let the eye see the light directly. /DVHU DSHUWXUH Interlock switches This machine has 1 (Top cover) Interlock switches to protect the laser light Leakage. Will power-off the system individually when the top cover is removed.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. Projector Power Cord ViewSonic Corporation (US/Canada/Latin America) : www.viewsonic.com/support/product-registration : 14035 Pipeline Ave.
Projector exterior view 1. 2. 3. 4. 5. 6. 7. 8. Front/upper side 9. 1 2 3 4 5 6 7 8 10. 11. 12. 13. 14. 15. 16. 17. 18. 9 Rear/lower side 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 28 23 Front IR remote sensor Projection lens Focus ring Zoom ring LENS SHIFT UP/DOWN LENS SHIFT RIGHT/LEFT Vent (air inlet) External control panel (See "Projector" on page 10 for details.
Controls and functions Projector 1 2 3 4 5 2 13 1. 2. 3. 4. 5. 6. 7. 8. LENS SHIFT UP/DOWN Rotate to move lens up or down. Focus ring Adjusts the focus of the projected image. Zoom ring Adjusts the size of the projected image. LENS SHIFT RIGHT/LEFT Rotate to move lens right or left. Menu Turns on the On-Screen Display (OSD) menu. Source Displays the source selection bar. (Left) Selects the desired menu items and makes adjustments.
13. 15. Temperature indicator light Lights up red if the projector's temperature becomes too high. Power indicator light Lights up or flashes when the projector is under operation. 14. 16. Light source indicator light Indicates the status of the light source. Lights up or flashes when the light source has developed a problem. Power Toggles the projector between standby mode and Power ON.
Remote control 1 2 3 4 5 6 7 8 19 20 21 22 23 24 9 10 11 12 13 14 15 16 17 25 26 27 28 29 30 18 1. 2. 3. 4. 5. 6. Power Toggles the projector between standby mode and Power ON. HDMI 1 Selects HDMI 1 source for display. COMP Selects D-Sub / Comp. source for display. HDBaseT Selects HDBaseT source for display. HDMI 3 Selects HDMI 3 source for display. Auto Sync Automatically determines the best picture timings for the displayed image. 12 7. 8. 9. 10.
11. 12. 13. 14. (Information) Displays the Information menu. PgUp (Page Up)/1 Operates your display software program (on a connected PC) which responds to page up commands (like Microsoft PowerPoint) when the mouse mode is activated. (Volume up)/2 Increase the volume level. PgDn (Page Down)/4 Operates your display software program (on a connected PC) which responds to page down commands (like Microsoft PowerPoint). Only available when a PC input signal is selected. 15. 16. 17. 18. 19. 20. 21. 22. 23.
Remote control code The projector can be assigned to 8 different remote control codes, 1 to 8. When several adjacent projectors are in operation at the same time, switching the remote control codes can prevent interference from other remote controls. Set the remote control code for the projector first before changing that for the remote control. To switch the code for the projector, select from among 1 to 8 in the SYSTEM SETTING > Remote Control Code menu.
Replacing the remote control batteries 1. 2. 3. Remove the cover by sliding it in the direction indicated by the arrow. Insert two new AAA batteries (check the polarity). Replace the cover. 2 3 WARNING • Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car. • Replace only with the same or equivalent type recommended by the battery manufacturer.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the following 4 possible installation locations: 1.
Projection dimensions LS800HD (1080P) The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. • 16:9 image on a 16:9 screen • 16:9 image on a 4:3 screen (e): Screen (f): Center of lens 16:9 image on a 16:9 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max. inch mm inch mm inch mm inch mm inch mm inch mm 50 1270 50 1273 83 2103 25 623 5.5 140 5.
16:9 image on a 4:3 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max. inch mm inch mm inch mm inch mm inch mm inch mm 54 1372 50 1262 82 2085 24 617 5.5 139 5.5 139 65 1651 60 1519 99 2510 29 743 6.6 167 6.6 167 76 1930 70 1776 116 2934 34 869 7.7 195 7.7 195 87 2210 80 2033 132 3359 39 994 8.8 224 8.8 224 98 2489 90 2290 149 3784 44 1120 9.9 252 9.
LS800WU (WUXGA) The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. • 16:10 image on a 16:10 screen (b) (a) (d) (c) (e) • 16:10 image on a 4:3 screen (b) (a) (d) (c) (f) (e): Screen (f): Center of lens 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max.
16:10 image on a 4:3 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max. inch mm inch mm inch mm inch mm inch mm inch mm 54 1372 50 1262 82 2085 27 686 4.1 103 4.1 103 65 1651 60 1519 99 2510 33 826 4.9 124 4.9 124 76 1930 70 1776 116 2934 38 965 5.7 145 5.7 145 87 2210 80 2033 132 3359 44 1105 6.5 166 6.5 166 98 2489 90 2290 149 3784 49 1245 7.4 187 7.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores. The connection illustrations below are for reference only.
Connecting a computer or a monitor Connecting a computer 1. 2. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN signal input socket on the projector. Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off.
video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video. See "Connecting a Component Video source device" on page 24 for how to connect the projector to a component video device. Least video quality Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.
LAN port and RS-232C port are disabled when Network Settigs to the HDBaseT and RS232 settings to HDBaseT channel. Use LAN cables of up to 100m long. Exceeding this length, the image will be deteriorated, and can experience malfunction on LAN transmission. HDBaseT BEST PRACTICE: i. When In Doubt, Use Shielded Cat6 With Shielded Plugs. ii. Use Proper Grounding. iii. Isolate HDBaseT Cat Cables from Other Signal Types.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • 1. 2. If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. Take a Video cable and connect one end to the composite Video output socket of the Video source device. Connect the other end of the Video cable to the VIDEO socket on the projector.
Operation Starting up the projector 1. 2. 3. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). (If available) Remove the lens cap. Press Power to start the projector. As soon as the light source lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Status Sub-menu Go to the previous page or to exit. Current input signal When projector is first time turned on after out of box, language selection will pop out automatically. 1. Press Menu to turn the OSD menu on. 3.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 27. You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Entering the password recall procedure 1. 2. 3. Continuous press Auto Sync on the remote or Auto on the key pad for 8 times. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. 2. Press Source. A source selection bar is displayed.
Adjusting the projected image Adjusting the projection angle The projector is equipped with two adjuster foot. It changes the image height and vertical projection angle. Screw the adjuster foot to fine tune the angle until the image is positioned where you want it. If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 34 for details.
Adjusting the horizontal image position With the lens horizontal image position can be adjusted to a maximum of 5% for 1080P and 5% for WUXGA of the image width. Note that the maximum horizontal image height adjustment can be limited by the vertical image position. For example it is not possible to achieve the maximum horizontal image position if the vertical image position is at maximum. Please consult the Shift Range diagram below for further clarification.
Adjusting projected image position using lens shift Vertical Lens Shift Knob Horizontal Lens Shift Knob The Lens Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertically within the range detailed below. Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio than traditional lens shift systems.
Fine-tuning the image clarity 1. Adjust the projected image to the size 2. that you need using the zoom ring. If necessary, sharpen the image by rotating the focus ring. Correcting keystone Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control 1.
Adjusting 4 corners Using the OSD menu Open the OSD menu and go to the DISPLAY > Corner Adj. menu. 1. It will show 4 corner adjustmant OSD on screen. 2. To select the corner you want to adjust than the selected area will show gray color 3. Two degree selection couble be adjust 4. To save the settings before you want to close the OSD menu How to reset the corner adj.: • • Press “Auto” to reset. The screen will show “Reset Notice: Do you want to reset? Reset / Cancel”.
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.
5. 6. Native: The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector away from the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments. 2.35:1: Scales an image so that it is displayed in the center of the screen with a 2.
Using Screen Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Screen Color feature can help correct the projected picture’s colors to prevent possible color difference between the source and projected pictures. To use this function, go to the DISPLAY > Screen Color menu and press / to select a color which is closest to the color of the projection surface.
Adjusting Brilliantcolor Go to the IMAGE > ADVANCED > Brilliantcolor menu and press / . This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in the projected picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors.
Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc.
Setting the presentation timer Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. 2. 3. Go to the BASIC > Presentation Timer menu. Press Enter to display the Presentation Timer page. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.
Hiding the image In order to draw the audience's full attention to the presenter, you can press BLANK to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden. You can set the blank time in the BASIC > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen.
Using the CEC function This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically. To turn on the CEC function: 1. 2.
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure you have turned on the corresponding menus under POWER MANAGEMENT > Standby Settings, and the cable connections are correctly made. For the connection methods, see the Connection chapter. Standy mode When HDBaseT switch on, Standby Settings mode will change to Normal. Green mode Power consumption <0.
Microphone Volume To adjust the microphone sound level, 1. Open the OSD menu and go to the BASIC > Audio Settings. 2. Press level. to highlight Microphone Volume and press / to select a desired sound Turning off the Power On/Off Ring Tone 1. Open the OSD menu and go to the BASIC > Audio Settings > Power On/Off Ring Tone menu. Press / to select Off. 2. The only way to change Power On/Off Ring Tone is setting On or Off here.
This projector is compliant to support Extron device(s) for reference. http://www.extron.com/ This projector supports all commands of PJLink Class1 (Version 1.00). http://pjlink.jbmia.or.jp/english/ For more detail of information about the diverse types of external devices which can be connected to the LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for each external device, kindly please get contact with the Support-Service team directly. LAN_RJ45 1.
3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). Click Properties. 5. 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
7. 8. 9. Press the MENU button on the projector. Select Advanced > Network Setting > Wired LAN. After getting into Wired LAN, input the following: • 10. DHCP: Off • IP Address: 10.10.10.10 • Subnet Mask: 255.255.255.0 • Gateway: 0.0.0.0 • DNS Server: 0.0.0.0 Press ENTER / . to confirm settings. Open a web browser (for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 11. In the Address bar, input the IP address: 10.10.10.10. 12. Press ENTER / .
Category Crestron Control Projector Network Configuration User Password Admin Password Item IP Address IP ID Port Projector Name Location Assigned To DHCP (Enabled) IP Address Subnet Mask Default Gateway DNS Server Enabled New Password Confirm Enabled New Password Confirm more information, please visit http://www.crestron.com.
Preparing Email Alerts 1. 2. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-ample, Microsoft Internet Explorer v6.01/v8.0). From the Homepage of LAN/RJ45, click Alert Settings. 3. By default, these input boxes in Alert Settings are blank.
4. For Sending alert mail, input the following: • The SMTP field is the mail server for sending out email (SMTP protocol). This is a required field. • The To field is the recipient’s email address (for example, the projector administrator). This is a required field. • The Cc field sends a carbon copy of the alert to the specified email address. This is an optional field (for example, the projector administrator’s assistant).
RS232 by Telnet Function Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated RS232 command control, there is alternative RS232 command control way, so called “RS232 by TELNET” for LAN/RJ45 interface. Quick Start-Guide for “RS232 by TELNET” 1. 2. 3. Check and get the IP-Address on OSD of the projector. Make sure that laptop/PC can access the web-page of the projector.
(ttt.xxx.yyy.zzz: IP-Address of the projector) If Telnet-Connection ready, and user can have RS232 command input, then Enter key pressed, the RS232 command will be workable.
How to have TELNET enabled in Windows VISTA / 7 / 8 / 10 By default installation for Windows VISTA / 7 / 8 / 10, “TELNET” function is not included. But end-user can have it by way of “Turn Windows features On or Off” to be enabled. 1. Open Control Panel in Windows VISTA / 7 / 8 / 10. 2. Open Programs. 3. Select Turn Windows features on or off to open.
4. Have Telnet Client option checked, then press OK button. Specsheet for “RS232 by TELNET” : 1. 2. 3. 4. Telnet: TCP. Telnet port: 4661. (for more detail, kindly please get contact with the service agent or team) Telnet utility: Windows “TELNET.exe” (console mode). Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly after TELNET connection ready.
Shutting down the projector 1. Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. 3. Press Power a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 45 for details.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options Off/Blackboard/Greenboard/ Whiteboard Auto/4:3/16:9/16:10/Native/2.
Main menu Sub-menu Auto Power On Options Computer HDMI CEC Direct Power On Auto Power Off Disable/Enable Disable/Enable Disable/Enable Off/On Disable/10 min/20 min/30 min 3.
Main menu Sub-menu Options 3D Sync 3D Settings HDMI Settings Network Settings RS232 Settings 5.
Main menu Sub-menu Language Projector Position Menu Settings 6. SYSTEM Options Multi-language OSD selection Front Table/Rear Table/ Rear Ceiling/Front Ceiling Menu Display 5 sec/10 sec/15 sec/20 sec/ Time 25 sec/30 sec Menu Center/Top-Left/Top-Right/ Position Bottom-Left/Bottom-Right High Altitude Mode Quick Auto Search Security Settings Off/On Off/On Change Password Power on Lock Panel Key Lock Remote Control Code Off/On Off/On 1/2/3/4/5/6/7/8 7.
Description of each menu Function Description See "Using Screen Color" on page 38 for details. Screen Color This function is only available when a PC input signal is selected. Aspect Ratio See "Selecting the aspect ratio" on page 36 for details. Keystone See "Correcting keystone" on page 34 for details. Corner Adj. See "Adjusting 4 corners" on page 35 for the details. Position Displays the position adjustment page. To move the projected image, use the directional arrow keys.
Function Description Color Mode See "Selecting a picture mode" on page 37 for details. Brightness See "Adjusting Brightness" on page 38 for details. Contrast See "Adjusting Contrast" on page 38 for details. Color Temp See "Selecting a Color Temperature" on page 39 and "Setting a preferred color temperature" on page 39 for details. Color See "Adjusting Color" on page 38 for details. Tint See "Adjusting Tint" on page 38 for details. 2.
Function Description Computer Selecting Enable allows the projector to turn on automatically once the VGA signal is fed through the VGA cable. 3. POWER MANAGEMENT menu Auto Power On HDMI Selecting Enable allows the projector to turn on automatically once the HDMI signal is fed through the HDMI cable. CEC See "Using the CEC function" on page 43 for details.
Function Description 3D Settings See "Using the 3D functions" on page 43 for details. HDMI Format Settings See "Changing HDMI input settings" on page 30 for details. 5. ADVANCED menu Network Settings Wired LAN • DHCP: If the projector installation environment has the Dynamic Host Configuration Protocol server. You can set this function ON to let the projector get the auto ID from server. If no DHCP, even you set ON for this function. You still need to input the projector ID by yourself.
Function 5. ADVANCED menu Light Source Settings Description Light Source Mode • Normal: Brightness will be 100% when set to Normal mode. If the projection environment requires brighter picture, you can set the light source mode to Normal for the highest projection brightness. • Eco: When set to Eco mode, the brightness will be 80% of the normal brightness.
Function Description Language Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 27 for details. Projector Position See "Choosing a location" on page 16 for details. Menu Settings 6. SYSTEM menu Menu Display Time Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments. Menu Position Sets the On-Screen Display (OSD) menu position.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
Light Source Hours information Getting to know the light source hours When the projector is in operation, the duration (in hours) of light source usage is automatically calculated by the built-in timer. To obtain the light source hour information: 1. Open the OSD menu and go to the ADVANCED > Light Source Setting menu. 2. Press Enter and the Light Source Settings page is displayed. 3. You will see the Light Source Hours information on the menu. 4. To leave the menu, press Exit.
Setting Power Saving The projector lowers the power consumption if no input source is detected after 5 minutes to prevent unnecessary waste of light source life. You can further decide if you would like the projector to turn off automatically after a set period of time. 1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy menu. 2. Press Enter and the Smart Energy page is displayed. 3. Highlight Power Saving and press / . 4.
Indicators Light Status & Description Blue Red Red ON Off Off Flashing Off Off Flashing Off Off 7 blinks Off Off 8 blinks Off Off 9 blinks Off Off 9 blinks 1 blinks Off Power events Light source Ready Start Cooling Case Open DMD Error Color Wheel Error Phosphor wheel error System events 2 blinks Off Off Off 1 blinks On Off 2 blinks On Off 3 blinks On Off 4 blinks On Off 5 blinks On 4 blinks Off Off 6 blinks 1 blinks Off 6 blinks 2 blinks Off 6 blinks 3 bl
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Projector specifications • • All specifications are subject to change without notice. Not all models can be purchased in your region. General Product name DLP Projector Optical Resolution Display system Light source LS800HD: 1920 x 1080 1080p LS800WU: 1920 x 1200 WUXGA 1-CHIP DMD Laser Diode Electrical Power supply Power consumption AC100–240V, 50–60 Hz (Automatic) 430 W (Max); < 0.5 W (Standby) Mechanical Weight 11 Kg (24.
Environmental Requirements Operating temperature Operating relative humidity Operating altitude Storage temperature Storage humidity Storage altitude 5°C–40°C at sea level 10%–90% (without condensation) • 0–1499 m at 5°C–35°C • 1500–3000 m at 5°C–25°C (with High Altitude Mode on) -10°C to +60°C 10% to 85% Non-Condensing 30°C@ 0 to 12200m above sea level Dimensions 360 mm (W) x 169 mm (H) x 452 mm (D) Ceiling mount installation 135.00mm (5.3") 160.00mm (6.3") Ceiling mount screws: M4 x 12 (Max.
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 UXGA 1600 x 1200 4:3 60 WSXGA+ 1680 x 1050 16:10 60 HD 1280 x 720 16:9 60 MAC 13" 640 x 480 4:3 67
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 WSXGA+ 1680 x 1050 16:10 60 HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 /
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 4:3 60* / 120** XGA 1024 x 768 4:3 60* / 120** HD 1280 x 720 16:9 60* / 120** WXGA 1280 x 800 16:9 60* / 120** HDTV (1080p) 1920 x 1080 16:9 60* Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SDTV (480i)*** 720 x 480 4:3 / 16:9 60 for Video Signal * 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequential formats.
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50 SDTV (480i) 720 x 480 4:3 / 16:9 60 SDTV (576i) 720 x 576 4:3 / 16:9 50 Composite video Signal Aspect Ratio Refresh Rate (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM 4:3 50 77
Copyright information Copyright Copyright 2017. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Appendix IR control table Key (with Blue back light) Format Byte1 Byte2 Byte3 Byte4 Power On NEC X3 F4 4F B0 Power Off NEC X3 F4 4E B1 COMP NEC X3 F4 41 BE A7 HDMI NEC X3 F4 58 HDMI2 NEC X3 F4 59 A6 HDMI3 NEC X3 F4 A2 5D HDBaseT NEC X3 F4 A3 5C Source NEC X3 F4 40 BF Auto sync NEC X3 F4 08 F7 Up / V keystone + NEC X3 F4 0B F4 F8 Blank NEC X3 F4 07 Left / H keystone - NEC X3 F4 0E F1 Enter NEC X3 F4 15 EA Right / H keystone +
RS232 command table Pin Description Pin 1 NC 2 Description RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None When select HDBaseT for RS232 control channel, change Baud rate to 9600.
Function Type Action Command ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset All Settings Write Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color Settings Write Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87 Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67 Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0
Function Type Action Command Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F Frame Sequential 0x06 0x14 0x00 0x04 0x00 0
Function Type Action Command Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 2.
Function Type Action Command Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x09 0x72 Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x33 0x00 0x92 Photo 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x13
Function Type Action Command Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71 Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72 Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0E 0x00 0x6C Increase 0x06 0x14 0x00 0x04 0x00 0x34
Function Type Action Command ON 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61 OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60 Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61 Increse 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61 Decrese 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62 Write Value 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x2A 0x11 0x9A Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64 Write Mute Read Write Volume Read 0x06 0x14 0x00 0
Function Type Action Command 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72 Write Language 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75 Vie 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x15 0x76 Read
Function Type Action Command OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88 ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89 Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89 Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66 OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x0
Function Type Action Command code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6 code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7 Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x48 0xA1 OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F Blackboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90 Greenboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91 Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92 Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11
Function Remote Key AMX Type Write Write Action Command Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Top 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Bottom 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x0
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Website T= Telephone C = CHAT ONLINE Email www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com http://www.viewsoniceurope.com/eu/support/call-desk/ Country/Region Australia New Zealand Hong Kong www.hk.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.