LS810/LS820/LS830 DLP Projector Podręcznik użytkownika Model nr VS16500/VS16501/VS16460
Informacje dotyczące zgodności Rozporządzenie Federalnej Komisji Łączności Niniejsze urządzenie pozostaje w zgodności z częścią 15 zasad Federalnej Komisji Łączności. Podstawą działania są dwa warunki: (1) niniejsze urządzenie nie wywołuje szkodliwych zakłóceń oraz (2) niniejsze urządzenie musi zaakceptować otrzymywane zakłócenia, włącznie z zakłóceniami, które mogą spowodować niepożądane działania.
Ważne informacje dotyczące bezpieczeństwa użytkowania 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Przeczytaj instrukcje. Zachowaj instrukcje. Weź pod uwagę wszelkie ostrzeżenia. Podążaj za instrukcjami. Nie należy używać niniejszej jednostki w pobliżu wody. Czyść za pomocą miękkiej, suchej szmatki. Nie należy blokować otworów wentylacyjnych. Instalacja powinna przebiegać zgodnie z instrukcjami wytwórcy.
Dyrektywa zgodności RoHS2 Produkt ten został zaprojektowany i wyprodukowany zgodnie z Dyrektywą 2011/65/EU Parlamentu Europejskiego i Rady Europy w sprawie ograniczenia stosowania niektórych substancji niebezpiecznych w urządzeniach elektrycznych i elektronicznych (Dyrektywa RoHS2), w związku z czym jest zgodny z podaną poniżej listą maksymalnych wartości koncentracji sporządzoną przez TAC (European Technical Adaptation Committee [Europejski Komitet Dostosowania Technicznego]): Proponowana maksymalna koncen
Informacje dotyczące rozprzestrzeniania Prawo autorskie © ViewSonic® Corporation, 2019. Wszystkie prawa zastrzeżone. Macintosh oraz Power Macintosh są znakami zastrzeżonymi dla Apple Inc. Microsoft, Windows, Windows NT, oraz logo Windows są znakami zastrzeżonymi dla Microsoft Corporation w Stanach Zjednoczonych oraz innych krajach. ViewSonic, logo trzech ptaków, OnView, ViewMatch, oraz ViewMeter są znakami zastrzeżonymi dla ViewSonic Corporation.
Spis treści Kluczowe instrukcje bezpieczeństwa................. 1 Wprowadzenie................... 3 Funkcje projektora...................................... 3 Zawartość opakowania............................... 4 Wygląd zewnętrzny projektora................... 5 Elementy sterowania i funkcje urządzenia ................................................. 6 Ustawianie projektora..... 12 Wybór miejsca.......................................... 12 Wymiary projekcji.....................................
Rozwiązywanie problemów....................... 50 Parametry techniczne..... 51 Specyfikacje projektora............................ 51 Wymiary.................................................... 52 Instalacja przy montażu sufitowym........... 52 Tabela taktowania..................................... 53 Informacje o prawach autorskich........................ 57 Prawa autorskie........................................ 57 Wyłączenie............................................... 57 Dodatek.....................
Kluczowe instrukcje bezpieczeństwa Projektor został zaprojektowany i przetestowany z uwzględnieniem najnowszych norm bezpieczeństwa dla urządzeń technologii informacyjnej. W celu zapewnienia bezpieczeństwa podczas użytkowania bardzo ważne jest jednak stosowanie się do instrukcji znajdujących się w niniejszym podręczniku i na etykietach produktu. Instrukcje bezpieczeństwa • Przed rozpoczęciem używania projektora należy przeczytać cały podręcznik. Należy zachować go do wykorzystania w przyszłości.
• Nie wolno blokować otworów wentylacyjnych. Jeżeli otwory wentylacyjne zostaną zatkane, przegrzanie urządzenia może spowodować zapalenie się elementów w jego wnętrzu. -- Nie wolno stawiać projektora na kocu, pościeli ani innej miękkiej powierzchni. -- Nie wolno przykrywać projektora materiałami ani innymi przedmiotami. -- W pobliżu projektora nie wolno umieszczać żadnych materiałów palnych. • Nie wolno stawać na projektorze ani umieszczać na nim żadnych przedmiotów.
Wprowadzenie Funkcje projektora Projektor posiada wysokiej jakości system optyczny i przyjazną dla użytkownika konstrukcję, co zapewnia niezawodność i łatwość użytkowania. Projektor oferuje poniższe funkcje.
Zawartość opakowania Należy ostrożnie rozpakować urządzenie i sprawdzić, czy zostały dostarczone wszystkie wymienione poniżej elementy. Jeśli czegoś brakuje, należy skontaktować się ze sprzedawcą, od którego projektor został kupiony. Standardowe akcesoria Dostarczone akcesoria zależą od regionu i mogą różnić się od przedstawionych na ilustracji.
Wygląd zewnętrzny projektora Przód/tył Bok Góra/dół Ostrzeżenie • Urządzenie to musi zostać uziemione. • Można zastosować mechanizm rozłączania zasilania w przewodach instalacji elektrycznej lub podłączyć kabel zasilający do pobliskiego gniazda elektrycznego. W razie wystąpienia awarii lub błędów podczas użytkowania urządzenia należy skorzystać z mechanizmu rozłączania zasilania w celu odcięcia zasilania lub odłączyć kabel zasilający od gniazda elektrycznego.
Elementy sterowania i funkcje urządzenia Projektor 1. (MÓJ PRZYCISK) Umożliwia przypisanie przycisku lub skrótu. Ustawienie należy dostosować w menu OSD. 2. DIODA LED STANU 3. / / / (przyciski korekcji keystone) Ręczna korekcja zniekształconych obrazów z powodu projekcji pod kątem. w lewo/w prawo/w górę/w dół Wybór i dostosowywanie żądanych pozycji menu. 4. DIODA LED ZASILANIA 5. (ZASILANIE) Przełączanie projektora pomiędzy trybem gotowości a stanem włączenia. 6.
Pilot zczegółowe informacje na temat S korzystania z przycisków zdalnego sterowania kursorem myszy (strona w górę, i ) można znaleźć w strona w dół, części “Używanie trybu kursora pilota”. 1. 2. 3. 4. 5. 6. Zasilanie 7. Przełączanie projektora pomiędzy trybem gotowości a stanem włączenia. Przycisk wyboru sygnału • COMP Wybór źródła sygnału D-Sub/Comp. • VIDEO Wybór źródła sygnału wideo. 8. • HDMI/MHL Wybór źródła sygnału HDMI/MHL. Auto Sync Automatyczny wybór najlepszej jakości wyświetlanego obrazu.
10. 11. 12. 13. 15. 16. 17. 18. 19. 20. (blokada przycisków panelu) Aby wyłączyć aktywną blokadę przycisków panelu, należy nacisnąć przycisk . 21. (timer prezentacji) Wyświetlanie menu ustawień timera 22. prezentacji. (głośność) 23. Wyświetlanie suwaka głośności. Eco Mode Wybór trybu źródła światła. 24. (Moje przyciski) Umożliwia ustawienie przycisku skrótu na pilocie. Ustawienie należy dostosować w menu OSD. 25. Źródło Wyświetlanie paska wyboru źródła. 26.
Używanie wskaźnika laserowego Wskaźnik laserowy to profesjonalne narzędzie do obsługi prezentacji. Naciśnięcie tego przycisku umożliwia wyemitowanie kolorowej wiązki wskaźnika laserowego. Wiązka lasera jest emitowana w spectrum światła widzialnego. W celu ciągłego generowania wiązki wskaźnika należy nacisnąć i przytrzymać przycisk [Laser]. ie wolno patrzeć na światło lasera ani kierować wiązki lasera w siebie lub w inne osoby. Przed N rozpoczęciem użytkowania należy przeczytać ostrzeżenia z tyłu pilota.
Używanie trybu kursora pilota W celu usprawnienia prezentacji pilota można używać do obsługi komputera. 1. Przed rozpoczęciem używania trybu kursora pilota podłącz jeden koniec kabla USB do portu mini USB projektora, a drugi do komputera PC lub notebooka. Szczegółowe informacje znajdują się w części “Podłączanie do komputera”. 2. Zmień sygnał wejściowy na D-Sub lub HDMI przez źródło PC. 3. Naciśnij przycisk [Mouse] na pilocie w celu przełączenia z trybu normalnego do trybu kursora.
Wymiana baterii pilota zdalnego sterowania 1. Aby otworzyć pokrywę baterii, ustaw pilota tylną stroną do góry. Naciśnij oznaczone miejsce, a następnie pociągnij pokrywę baterii do góry, zgodnie ze wskazanym kierunkiem. 2. Wyjmij stare baterie (w razie konieczności), a następnie włóż 2 baterie AAA zgodnie z oznaczeniem biegunów. Dodatni biegun baterii należy umieścić w miejscu oznaczenia (+), a ujemny biegun w przeciwnym kierunku. 3. Wyrównaj pokrywę baterii z dolną częścią pilota i dociśnij ją.
Ustawianie projektora Wybór miejsca Miejsce instalacji projektora należy wybrać na podstawie układu pomieszczenia lub własnych preferencji. Należy uwzględnić rozmiar i położenie ekranu, lokalizację odpowiedniego gniazda elektrycznego, a także ustawienie oraz odległość między projektorem i innymi urządzeniami. Projektor można zainstalować w jednej z 4 możliwych lokalizacji: 1. Przód – stół Przy tym ustawieniu projektor jest umieszczony przed ekranem.
Wymiary projekcji Ekrany omawiane poniżej to ekrany projekcji składające się z powierzchni ekranu i konstrukcji nośnych. (W) (H) (a) (b) Odległość od środka obiektywu do strony tylnej wynosi 272mm. • LS810 Screen size (D) in mm 80 2032 90 2286 100 2540 110 2794 120 3048 130 3302 140 3556 150 3810 Image width (W) in mm 67.84 1723 76.32 1939 84.80 2154 93.28 2369 101.76 2585 110.24 2800 118.72 3015 127.2 3231 Image height (H) in mm 42.40 1077 47.70 1212 53.00 1346 58.30 1481 63.60 1615 68.90 1750 74.
Podłączanie Podczas podłączania źródła sygnału do projektora należy sprawdzić, czy: 1. Wszystkie podłączane urządzenia są wyłączone. 2. Użyto prawidłowych kabli sygnałowych dla każdego źródła. 3. Kable zostały prawidłowo podłączone. przypadku niektórych pokazanych poniżej połączeń wymagane są kable, które nie są W dostarczane wraz z projektorem (patrz “Zawartość opakowania”). Niezbędne kable sygnałowe można kupić w sklepie z elektroniką.
Podłączanie do komputera lub monitora Podłączanie do komputera 1. Użyj dostarczonego kabla VGA. Podłącz jeden koniec do gniazda wyjścia DSub w komputerze. 2. Podłącz drugą wtyczkę kabla VGA do gniazda sygnału wejściowego COMPUTER IN1 lub IN2 projektora. 3. Aby móc korzystać z funkcji zdalnego sterowania kursorem myszy, podłącz większą wtyczkę kabla USB do portu USB komputera, a mniejszą do portu MINI USB projektora. Szczegółowe informacje znajdują się w części “Używanie trybu kursora pilota”.
Podłączanie do źródłowych urządzeń wideo Projektor można podłączyć do źródłowego urządzenia wideo z dowolnym z poniższych gniazd wyjściowych: • HDMI • Komponentowe wideo • S-Video • Wideo (kompozytowe wideo) Do podłączenia projektora do źródłowego urządzenia wideo wystarczy tylko 1 z wymienionych powyżej metod połączenia. Różne metody połączeń zapewniają jednak inną jakość wideo. Wybór metody połączenia zależy od dostępności odpowiednich złączy w projektorze i źródłowym urządzeniu wideo.
Podłączanie do urządzeń HDMI Projektor należy podłączyć do urządzenia HDMI przy użycia kabla HDMI. 1. Podłącz jeden koniec kabla HDMI do gniazda wyjścia HDMI urządzenia wideo. 2. Podłącz drugi koniec kabla do gniazda wejścia sygnału HDMI w projektorze. przypadku podłączenia projektora do odtwarzacza DVD przez wejście HDMI projektora i W nieprawidłowego wyświetlania kolorów, należy zmienić przestrzeń kolorów na YUV. Szczegółowe informacje znajdują się w części “Zmiana ustawień wejścia HDMI”.
Podłączanie do źródłowych kompozytowych urządzeń wideo Należy sprawdzić, czy w źródłowym urządzeniu wideo dostępne jest wolne gniazdo wyjścia sygnału kompozytowego: • Jeśli tak, można kontynuować wykonywanie procedury. • Jeśli nie, należy wybrać inną metodę podłączenia urządzenia. 1. Podłącz jeden koniec kabla wideo do gniazda wyjścia kompozytowego sygnału wideo źródłowego urządzenia wideo. 2. Podłącz drugi koniec kabla wideo do gniazda VIDEO projektora.
Obsługa Włączanie projektora Podłącz przewód zasilający do projektora i do gniazda elektrycznego. Włącz gniazdo elektryczne (jeśli posiada włącznik). Naciśnij przycisk zasilania w celu włączenia projektora. Jeśli włączasz projektor po raz pierwszy, wykonaj instrukcje ekranowe i wybierz język menu OSD. Włącz wszystkie podłączone urządzenia. Projektor rozpocznie wyszukiwanie sygnałów wejścia. W prawym dolnym rogu ekranu widoczny będzie aktualnie wyszukiwany sygnał wejścia.
1. Naciśnij przycisk i wybierz menu 2. WYŚWIETLACZ, a następnie naciśnij przycisk /, aby wybrać kolor ekranu. Naciśnij przycisk i wybierz menu OBRAZ, a następnie naciśnij przycisk /, aby wybrać tryb koloru podstawowego. OBRAZ WYŚWIETLACZ Typ ekranu Współczynnik proporcji Korekcja trapezowa Korekcja rogów Położenie Faza Wielkość horyz. Zoom Overscan Wył.
Wyłączanie funkcji hasła Dla celów bezpieczeństwa i dla uniemożliwienia nieautoryzowanego używania projektor został wyposażony w funkcję zabezpieczenia hasłem. Hasła można ustawić za pomocą menu ekranowego (OSD). Szczegółowe informacje na temat obsługi menu OSD można znaleźć w części [Korzystanie z menu]. iepamiętanie hasła po skonfigurowaniu ochrony hasłem może okazać się problemem. N Zalecane jest zapisanie hasła i schowanie go w bezpiecznym miejscu, aby móc sprawdzić je w przypadku zapomnienia.
Procedura odzyskiwania hasła 1. 2. 3. Naciśnij przycisk [Auto Sync] na pilocie i przytrzymaj go przez 3 sekundy. Na ekranie projektora wyświetlony zostanie zakodowany numer. Zapisz numer i wyłącz projektor. O pomoc w odkodowaniu numeru poproś pracownika lokalnego centrum serwisowego. Może być wymagane przedstawienie dowodu zakupu w celu potwierdzenia prawa do używania projektora. Widoczny na powyższym zrzucie ekranu numer [XXX] zależy od numeru modelu projektora. Zmiana hasła 1. 2. 3. 4. 5. 6. 7.
Przełączanie sygnału wejścia 1. 2. Projektor może być podłączony jednocześnie do kilku urządzeń. W danym czasie może on jednak wyświetlać tylko jeden obraz pełnoekranowy. Aby projektor automatycznie wyszukiwał różne sygnały, należy ustawić dla dostępnej w menu SYSTEM funkcji Szybkie autowyszukiwanie opcję Wł.. Można także nacisnąć przycisk wyboru źródła na pilocie lub wyszukać dostępne sygnały wejścia w celu ręcznego wybrania żądanych sygnałów.
Zmiana ustawień wejścia HDMI 1. 2. 3. 4. W przypadku podłączenia projektora do urządzenia (takiego jak odtwarzacz DVD lub Blu-ray) przez gniazdo wejścia HDMI projektora i nieprawidłowego wyświetlania kolorów, należy zmienić ustawienia przestrzeni kolorów na zgodne z ustawieniami przestrzeni kolorów urządzenia wyjściowego. Aby wykonać tę czynność: Otwórz menu OSD i przejdź kolejno do pozycji ZAAWANSOWANE > Ustawienia HDMI. Naciśnij przycisk [Enter].
Regulacja wyświetlanego obrazu Regulacja kąta projekcji Projektor jest wyposażony w regulowaną nóżkę. Za pomocą regulowanej nóżki można dostosowywać wysokość i kąt projekcji względem osi pionowej. Przekręcając regulowaną nóżkę, użytkownik może dokładnie ustawić żądany kąt projekcji i położenie wyświetlanego obrazu. Jeśli projektor stoi na nierównej powierzchni lub ekran i projektor nie są do siebie ustawione pod kątem prostym, na wyświetlonym obrazie mogą wystąpić zniekształcenia trapezowe (keystone).
Korekcja zniekształceń trapezowych Zniekształcenia trapezowe (keystone) to problem polegający na wyświetlaniu obrazu o kształcie trapezu w wyniku nieprawidłowo ustawionego kąta projekcji. W celu korekcji należy dostosować wysokość projektora oraz wykonać poniższe czynności, aby ręcznie rozwiązać problem. • Przy użyciu pilota zdalnego sterowania 1. Naciśnij przycisk 2. Naciśnij przycisk , aby skorygować zniekształcenia trapezowe w górnej części obrazu.
Dopasowanie 4 narożników Można ręcznie dostosować nieregularne kształty i rozmiary w celu uzyskania obrazu o kształcie prostokąta. 1. 2. 3. 4. Korekcja rogów Aby wyświetlić stronę Korekcja rogów, wykonaj jedną z poniższych czynności: i. Naciśnij przycisk [Enter]. Naciśnij przycisk [Menu/Exit], aby zapisać lub wyjść ii. Otwórz menu OSD, przejdź kolejno do pozycji WYŚWIETLACZ > Korekcja rogów, a następnie naciśnij przycisk [Enter]. Wyświetlona zostanie strona Korekcja rogów.
Powiększanie w celu uzyskania szczegółowego widoku Wyświetlony obraz można powiększyć w celu przeanalizowania jego szczegółów. Aby przesunąć obraz, należy użyć przycisków strzałek. • Przy użyciu pilota zdalnego sterowania 1. Naciśnij przycisk na pilocie zdalnego sterowania, aby wyświetlić pasek powiększania. 2. Naciśnij kilkakrotnie przycisk , aby powiększyć obraz do żądanego rozmiaru. 3.
Informacje dotyczące współczynnika proporcji a poniższych ilustracjach fragmenty zaznaczone na czarno są nieaktywne, natomiast N fragmenty zaznaczone na biało są aktywne. Menu OSD mogą być wyświetlane w tych nieużywanych czarnych obszarach ekranu. 1. 2. 3. 4. Automatyczny: proporcjonalne skalowanie obrazu w celu dopasowania natywnej rozdzielczości projektora w poziomie.
Optymalizacja obrazu Wybór trybu obrazu W ustawieniach projektora dostępnych jest kilka zdefiniowanych wstępnie trybów obrazu. Można wybrać tryb najbardziej odpowiedni dla danych warunków pracy i typu wejściowego sygnału obrazu. Aby wybrać żądany tryb pracy, należy wykonać poniższe czynności. • Naciśnij kilka razy przycisk [Color Mode] do momentu wybrania żądanego trybu. • Przejdź kolejno do pozycji OBRAZ > Tryb kolorów i naciśnij przycisk /, aby wybrać żądany tryb.
Dokładne dopasowanie jakości obrazu w trybach użytkownika Po wykryciu przez projektor określonych typów sygnału można zastosować kilka definiowanych przez użytkownika funkcji. Funkcje te można konfigurować zgodnie z własnymi potrzebami. Regulacja jasności Przejdź kolejno do pozycji OBRAZ > Jasność, a następnie naciśnij przycisk /. Im wyższa wartość, tym jaśniejszy obraz. Odpowiednio, im niższe ustawienie, tym ciemniejszy obraz.
Regulacja funkcji Brilliant Color Przejdź kolejno do pozycji OBRAZ > Zaawansowane > Brilliant Color, a następnie naciśnij przycisk /. Funkcja ta wykorzystuje nowy algorytm przetwarzania kolorów oraz ulepszenia systemowe, które umożliwiają osiągnięcie większej jasności, a zarazem prawdziwszych i bardziej wyrazistych kolorów wyświetlanego obrazu.
Zarządzanie kolorami Skorzystanie z funkcji zarządzania kolorami należy rozważyć w stałych instalacjach projektora w miejscach, gdzie poziom oświetlenia można kontrolować, np. w salach posiedzeń, w salach wykładowych lub w kinie domowym. Funkcja zarządzania kolorami umożliwia precyzyjną regulację kolorów, co zapewnia wierniejsze wyświetlanie kolorów.
Ustawianie timera prezentacji Timer prezentacji może wskazywać na ekranie czas prezentacji, aby pomóc w lepszym zarządzaniu czasem podczas tego typu wystąpień. Aby skorzystać z tej funkcji, należy wykonać poniższe czynności: 1. Naciśnij przycisk na pilocie, aby przejść do menu Licznik prezentacji lub przejdź kolejno do pozycji Podstawowe > Licznik prezentacji. 2. Naciśnij przycisk [Enter], aby wyświetlić stronę Licznik prezentacji. 3.
Ukrywanie obrazu Aby skupić uwagę na osobie wykonującej prezentację, można nacisnąć przycisk Blank, który ukrywa wyświetlany obraz. Naciśnięcie dowolnego przycisku na projektorze lub pilocie umożliwi przywrócenie obrazu. Po ukryciu obrazu w prawym dolnym rogu ekranu widoczny będzie komunikat [PUSTY]. Czas wyświetlania pustego ekranu można ustawić, przechodząc kolejno do pozycji Podstawowe > Timer wygaszenia. Po ukończeniu odliczania pustego ekranu obraz zostanie automatycznie wyświetlony ponownie.
Tworzenie własnego ekranu startowego 1. 2. 3. 4. 5. 6. Oprócz ekranu Czarny, Niebieski lub ViewSonic jako ekran startowy można także ustawić obraz wyświetlany z komputera lub urządzenia wideo. W celu utworzenia własnego ekranu startowego: Wybierz żądany obraz ekranu startowego z komputera lub źródłowego urządzenia wideo. Otwórz menu OSD i przejdź kolejno do pozycji Podstawowe > Przech. ekranu. Naciśnij przycisk [Enter]. Wyświetlony zostanie komunikat potwierdzenia. Ponownie naciśnij przycisk [Enter].
Korzystanie z funkcji CEC 1. 2. Projektor ten obsługuje funkcję CEC (Consumer Electronics Control), umożliwiającą podłączanie urządzeń HDMI i obsługę zsynchronizowanego włączania/wyłączania zasilania. Oznacza to, że jeśli urządzenie, które także obsługuje funkcję CEC, jest podłączone do wejścia HDMI projektora, jego zasilanie zostanie wyłączone automatycznie po wyłączeniu zasilania projektora.
Uaktywnij wyjście VGA Po prawidłowym podłączeniu odpowiednich urządzeń do gniazd COMPUTER IN i COMPUTER OUT należy wybrać opcję Wł. w celu wygenerowania sygnału wyjściowego VGA. Projektor będzie odbierał sygnały wyjściowe tylko przez gniazdo Computer In 1. Uaktywnij wyjście audio Po prawidłowym podłączeniu urządzenia do gniazda AUDIO IN należy wybrać opcję Wł. w celu odtworzenia sygnałów audio. Regulacja dźwięku Opisana poniżej regulacja dźwięku wpływa na głośnik(i) projektora.
Obsługa menu System menu Należy pamiętać, że menu ekranowe (OSD) może być inne w zależności od typu odbieranego sygnału. Do korzystania z pozycji menu konieczne jest wykrycie przez projektor co najmniej jednego prawidłowego sygnału. Jeśli do projektora nie podłączono sprzętu lub nie został wykryty żaden sygnał, dostępnych będzie tylko kilka elementów menu. Menu główne Podmenu Typ ekranu Współczynnik proporcji 1. Wyświetlacz Korekcja trapezowa Korekcja rogów Położenie Faza Wielkość horyz.
Menu główne Automatyczne włączanie 3. Zarządzanie zasilaniem Podmenu Komputer CEC Bezpośrednie włączenie zasilania Automatyczne wyłączanie Inteligentne zarządzanie energią Ustawienia MHL Ust. gotow. Ustawienia dźwięku Licznik prezentacji 4. Wzorzec Podstawowe Timer wygaszenia Licznik uśpienia Oszcz. ener. Wyjście zasilania Resetowanie MHL Uaktywnij wyjście VGA Uaktywnij wyjście audio Tryb audio Wycisz Głośność Okres licznika Wyświetlanie czasu Położenie licznika Metoda odliczania licznika Rozp.
Menu główne Podmenu Okulary 3D Ustawienia 3D Ustawienia HDMI Synchronizacja 3D Synchron. 3D, Wyłącz/Odwrócony odwrócony Format HDMI Autom./RGB/YUV Zakres HDMI Autom./Rozszerzony/Normalny Ustawienie sterowania DHCP włączony/Statyczny przez sieć LAN adres IP Adres IP projektora 5.
Opis każdego menu FUNKCJA Typ ekranu Współczynnik proporcji Korekcja trapezowa Korekcja rogów 1. Menu Wyświetlacz Położenie Opis Szczegółowe informacje znajdują się w części “Korzystanie z funkcji koloru ekranu”. Szczegółowe informacje znajdują się w części “Wybór współczynnika proporcji”. Szczegółowe informacje znajdują się w części “Korekcja zniekształceń trapezowych”. Szczegółowe informacje znajdują się w części “Dopasowanie 4 narożników”. Wyświetlanie strony regulacji położenia.
FUNKCJA Opis Kolor Szczegółowe informacje znajdują się w części “Regulacja kolorów”. Odcień Szczegółowe informacje znajdują się w części “Regulacja odcienia”. Ostrość Szczegółowe informacje znajdują się w części “Regulacja ostrości”. 2. Menu Obraz Zaawansowane Gamma Szczegółowe informacje znajdują się w części “Wybór ustawienia gamma”. Brilliant Color Szczegółowe informacje znajdują się w części “Regulacja funkcji Brilliant Color”.
FUNKCJA Ustawienia dźwięku Licznik prezentacji 4. Menu Podstawowe Opis Szczegółowe informacje znajdują się w części “Regulacja dźwięku”. Szczegółowe informacje znajdują się w części “Ustawianie timera prezentacji”. Projektor może wyświetlić kilka wzorców testowych. Wzorzec jest pomocny w regulacji rozmiaru i ostrości obrazu, a Wzorzec także umożliwia sprawdzenie, czy wyświetlany obraz jest pozbawiony zakłóceń. Szczegółowe informacje znajdują się w części “Ukrywanie Timer wygaszenia obrazu”.
FUNKCJA 5. Menu Zaawansowane Napis zamknięty Opis Wybór preferowanego trybu napisów kodowanych, gdy są one zapewniane przez wybrany sygnał wejściowy. • Napisy: wyświetlanie dialogów, narracji oraz efektów dźwiękowych w programach telewizyjnych i filmach wideo zarejestrowanych z napisami kodowanymi (w opisach telewizyjnych mają zwykle oznaczenie “CC”). Funkcja ta jest dostępna tylko wtedy, gdy wybrany jest sygnał wejścia kompozytowy wideo lub S-Video i gdy formatem systemu jest NTSC.
FUNKCJA Opis Źródło Wyświetlanie aktualnego źródła sygnału. Tryb kolorów Wyświetlanie trybu wybranego w menu Obraz. Rozdzielczość 6. Menu Informacje Wyświetlanie natywnej rozdzielczości sygnału wejścia. System kolorów Aktualny status systemu Wyświetlanie formatu systemu sygnałów wejściowych. Adres IP Wyświetlanie adresu IP projektora. Adres MAC Wyświetlanie adresu MAC projektora.
Konserwacja urządzenia Jak dbać o projektor Obiektyw i/lub filtr należy regularnie czyścić. Nie wolno demontować żadnej części tego projektora. Jeśli jakieś części wymagają wymiany, należy skontaktować się ze sprzedawcą. Czyszczenie obiektywu Pyłoszczelny szklany obiektyw należy czyścić w razie zauważenia brudu lub kurzu na jego powierzchni. • Do usuwania zanieczyszczeń należy stosować sprężone powietrze.
Korzystanie z filtra Uwaga • Zalecane jest okresowe czyszczenie filtrów użytkowanego projektora. • J eśli projektor jest zawieszony na suficie lub zamontowany w sposób utrudniający dostęp do niego, filtr należy wymieniać z zachowaniem szczególnej ostrożności. Czyszczenie filtrów 1. Upewnij się, że projektor został wyłączony i odłączony od źródła zasilania. 2. Naciśnij zaczep filtra i wyjmij go z projektora. 3. Oczyść filtr z kurzu za pomocą małego odkurzacza lub miękkiej szczoteczki. 4.
Wskaźnik LED Stan projektora Wskaźnik zasilania Wskaźnik stanu* Tryb gotowości Czerwony Wył. Włączanie zasilania Miga na czerwono przez dwie sekundy, miga na fioletowo przez trzy sekundy, a następnie miga na niebiesko przez 4 sekundy Wył. Normalna praca Niebieski Wył. Normalne wyłączanie Miga na niebiesko Wył. Błąd wentylatora Wył. Miga na czerwono Temperatura Wył.
Rozwiązywanie problemów Projektor nie wyłącza się Przyczyna Rozwiązanie Podłącz jeden koniec kabla zasilającego do wejścia zasilania AC projektora, a drugi koniec do gniazda elektrycznego. Jeśli gniazdo elektryczne ma włącznik, upewnij się, że jest on włączony. Zaczekaj na zakończenie procesu chłodzenia. Brak zasilania przez przewód zasilający. Podjęto próbę ponownego włączenia projektora w czasie procesu chłodzenia.
Parametry techniczne Specyfikacje projektora • Wszystkie specyfikacje mogą ulec zmianie bez powiadomienia. • W danym regionie niektóre modele projektora mogą być niedostępne. L810 L820 L830 Złącza wejścia 1 Wejście VGA (DB 15-pinowe) x2 x2 x2 2 Wejście audio (mini jack) x1 x1 x1 3 Audio L/R (RCA x2 kompozytowe) x1 x1 x1 4 HDMI (wer. 1.4 z dźwiękiem) x1 x1 x1 5 HDMI 1.4/MHL 2.
Wymiary 508,3mm 392,7mm 165,2mm Instalacja przy montażu sufitowym 137 10,1 200 110,1 Kierunek projekcji 155 188 Uwaga: Zalecane jest zamontowanie projektora przy użyciu śrub M6L12 i otworów na śruby M6 do montażu podwieszanego.
Tabela taktowania Analogowy RGB Sygnał Rozdzielczość (piksele) Współczynnik proporcji Częstotliwość odświeżania (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 XGA 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 UXGA 1600 x 1200 4:3 60 WSXGA+ 1680 x 1050 16:10 60 HD 1280 x 7
HDMI Sygnał Rozdzielczość (piksele) Współczynnik proporcji Częstotliwość odświeżania (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 WSXGA+ 1680 x 1050 16:10 60 HDTV (1080p) 1920 x 1080 16:9 50/60 HDTV (1080i) 1920 x 1080 16:9 50/60 HDTV (720p) 1280 x 720 16:9 50/60 SDTV (
3D (łącznie z sygnałem HDMI) Sygnał Rozdzielczość (piksele) Współczynnik proporcji Częstotliwość odświeżania (Hz) SVGA 800 x 600 4:3 60*/120** XGA 1024 x 768 4:3 60*/120** HD 1280 x 720 16:9 60*/120** WXGA 1280 x 800 16:9 60*/120** Sygnał Rozdzielczość (piksele) Współczynnik proporcji Częstotliwość odświeżania (Hz) SDTV (480i)*** 720 x 480 4:3/16:9 60 Dla sygnału wideo * Sygnały 60 Hz są obsługiwane w formacie równoległym, góra-dół i kolejnych klatek.
Komponentowe wideo Sygnał Rozdzielczość (piksele) Współczynnik proporcji Częstotliwość odświeżania (Hz) HDTV (1080p) 1920 x 1080 16:9 50/60 HDTV (1080i) 1920 x 1080 16:9 50/60 HDTV (720p) 1280 x 720 16:9 50/60 SDTV (480p) 720 x 480 4:3/16:9 60 SDTV (576p) 720 x 576 4:3/16:9 50 SDTV (480i) 720 x 480 4:3/16:9 60 SDTV (576i) 720 x 576 4:3/16:9 50 Kompozytowy wideo Sygnał Współczynnik proporcji Częstotliwość odświeżania (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM
Informacje o prawach autorskich Prawa autorskie Copyright 2015 Wszelkie prawa zastrzeżone. Żadna z części niniejszej publikacji nie może być powielana, przesyłana, przetwarzana, przechowywana w jakimkolwiek systemie gromadzenia danych ani tłumaczona na jakikolwiek język w tym komputerowy, w żadnej formie ani żadnymi środkami - w tym elektronicznie, mechanicznie, magnetycznie, optycznie, chemicznie, ręcznie lub w żaden inny sposób, bez uprzedniej pisemnej zgody firmy ViewSonic.
Dodatek Tabela sterowania podczerwienią Przycisk Format Bajt 1 Bajt 2 Bajt 3 Bajt 4 Strona w dół NEC X3 F4 05 FA Strona w górę NEC X3 F4 06 F9 Blank NEC X3 F4 07 F8 Autosynchronizacja NEC X3 F4 08 F7 W górę NEC X3 F4 0B F4 W dół NEC X3 F4 0C F3 W lewo NEC X3 F4 0E F1 W prawo NEC X3 F4 0F F0 Tryb kolorów NEC X3 F4 10 EF Wycisz NEC X3 F4 14 EB Enter NEC X3 F4 15 EA Włączenie zasilania NEC X3 F4 17 E8 Licznik prezentacji NEC X3 F4
Address Code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin Description Pin Description 1 NC 2 RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 19200bps (default) Data Length 8 bit Parity check None Stop bit 1 bit flow control None 59 59
FUNCTION Status Operation cmd Activate 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Write Power supply Read Power status (ON/OFF) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset All Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset color settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87 Write Splash Screen - Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Real ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Write Projector Position Read Projector Position status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F Frame Sequential 0x06 0x1
Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68 Aspect ratio 2.
Keystone Correction Horizontal Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F Write Read Write Keystone Correction status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E Dynamic 0x
Write Source input Read Quick Auto Search Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 Input source VGA2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68 Input source HDMI 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63 Input source HDMI/ MHL 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67 Input source Composite video 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 Input source SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66 Source 0x07 0x14 0x00 0x05 0x
Write Language ENGLISH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 FRANÇAIS 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 DEUTSCH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 ITALIANO 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 ESPAÑOL 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 繁體中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 日本語 0x06 0x14 0x
Write RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format Read Write HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88 HDMI range Read HDMI Range status 0x07 0x14 0x00 0x05
Code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0 Code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1 Code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2 Code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3 Code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4 Code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5 Code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6 Code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7 Write Remote control code Read Remote
Remote Key Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Input 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67 Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0
Pomoc techniczna klienta W celu uzyskania informacji o pomocy technicznej lub serwisu produktu, patrz tabela poniżej,lub skontaktuj się z dostawcą. UWAGA: Należy przygotować numer seryjny produktu. Kraj/Region Witryna internetowa Telefon E-mail Polska i inne kraje Europy Centralnej www.viewsoniceurope.com www.viewsoniceurope.com/ uk/support/call-desk/ service_pl@ viewsoniceurope.
Ograniczona Gwarancja Projektor ViewSonic® Zakres gwarancji: Firma ViewSonic gwarantuje, że przy normalnym użytkowaniu, w okresie gwarancji jej produkty będą wolne od defektów materiałowych i wad wytwarzania. Jeżeli w okresie gwarancyjnym wystapią defekty materiałowe lub wady wytwarzania produktu, firma ViewSonic według własnego uznania, naprawi lub wymieni produkt na inny podobny. Wymieniony produkt lub jego podzespoły, mogą zawierać części lub elementy wyremontowane lub odnowione.
Uzyskiwanie usługi: 1. Informacje dotyczące uzyskiwania usługi gwarancyjnej, można uzyskać w dziale obsługi klientów ViewSonic (sprawdź informacje na stronie pomocy technicznej klienta). Konieczne jest podanie numeru seryjnego produktu. 2. W celu uzyskania usługi gwarancyjnej należy przedstawić (a) oryginalny dowód sprzedaży z datą sprzedaży, (b) imię i nazwisko, (c) adres, (d) opis problemu oraz (e) numer seryjny produktu. 3.