M1+ Portable LED Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our web site at http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website.
Thank you for choosing ViewSonic® As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic® product you have chosen will serve you well.
Safety Precautions Please read the following Safety Precautions before you start using the projector. • Keep this user guide in a safe place for later reference. • Read all warnings and follow all instructions. • Allow at least 20“ (50 cm) clearance around the projector to ensure proper ventilation. • Place the projector in a well-ventilated area. Do not place anything on the projector that prevents heat dissipation. • Do not place the projector on an uneven or unstable surface.
• Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply and call your local service center to have the projector serviced. • When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal operation and not a defect. • Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug.
Contents Safety Precautions........................................................ 3 Introduction................................................................. 8 Package Contents....................................................................................................8 Product Overview....................................................................................................9 Projector...................................................................................................
Using the Projector..................................................... 25 Starting Up the Projector.......................................................................................25 Adjusting the Projected Image..............................................................................26 Adjusting the Projector's Height and Projection Angle.......................................... 26 Adjusting the Focus.............................................................................................
Appendix.................................................................... 70 Specifications.........................................................................................................70 Timing Chart..........................................................................................................71 HDMI/USB C Video Timing..................................................................................... 71 HDMI/USB C Support PC Timing.................................................
Introduction Package Contents 1 4 3 2 OK 5 6 7 Item Description [1] Projector [2] Power Cord [3] [4] USB Type C Cable Power Adapter [5] [6] [7] Remote Control with Batteries Carrying Bag Quick Start Guide 8
Product Overview Projector 19 2 1 4 6 5 7 8 10 14 12 13 11 9 15 ENTER 3 Micro SD DC 19V USB-C HDMI USB READER 5V/1A OUT 16 17 1 2 3 4 5 Item Description Item Description [1] Speaker [11] Enter1/ Power Button2 [2] IR Receiver [12] Volume Down3 [3] [4] Tripod mount Focus Ring [13] [14] Volume Up4 Return5 [5] [6] [7] [8] [9] [10] Micro SD slot DC IN USB-C HDMI Audio Out USB Type A [15] [16] [17] [18] [19] Speaker PR IR Receiver Battery Indicator Smart Stand Lens Enacts
Remote Control 1 2 3 4 5 OK 6 7 9 10 11 12 13 Button Description [1] Power Turns the projector On or Off [2] Source Displays the input source selection menu [3] Focus Automatically focus the image1 [4] Bluetooth Mode [5] Up/Down/Left/Right Enable Bluetooth Navigate and select menu items; Keystone adjustment [6] OK Confirms the selection [7] Setting Displays the Setting menu [8] Return Returns to the previous screen [9] Home Access the Home screen [10] Volume Control Increase or
Remote Control - Effective Range To ensure proper function of the remote control follow the steps below: 1. The remote control must be held at an angle within 30° perpendicular to the projector’s IR remote control sensor(s). 2. The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.) Remote Control - Replacing the Batteries 1. To open the battery cover, turn the remote control over to view its back, open the cover in the direction of the arrow. 2.
Initial Setup This section provides detailed instructions for the initial set up your projector. Choosing a Location - Projection Orientation Personal preference and room layout will decide the installation location. Consider the following: • Size and position of your screen. • Location of a suitable power outlet. • Location and distance between the projector and other equipment.
Projection Dimensions • 16:9 Image on a 16:9 Screen NOTE: (e) = Screen / (f) = Center of Lens 16:9 Image on a 16:9 Screen (a) Screen Size (b) Projection Distance (c) Image Height Image Width in. cm in. m in. cm in. mm 30 76.2 32.16 0.82 14.7 37.36 26.15 664 40 101.6 42.88 1.09 19.6 49.81 34.86 886 50 127 53.6 1.36 24.5 62.26 43.58 1107 60 152.4 64.32 1.63 29.4 74.72 52.29 1328 70 177.8 75.04 1.91 34.3 87.17 61.01 1550 80 203.2 85.76 2.18 39.2 99.
Making Connections This section guides you on how to connect the projector with other equipment. Connecting to Power DC Power (Power Outlet) 1. Connect the power cord to the power adapter. 2. Connect the power adapter to the DC IN jack at the side of the projector. 3. Connect the power cord plug to a power outlet. When connected, the status LED will turn red. 2 3 1 NOTE: • Charge the projector for 4.5 hours via the power adapter before using it in battery mode for the first time.
Power on by Power Bank Function The projector can also be powered by a power bank. 1 2 15V/3A To power your projector: 1. Connect one end of the USB Type-C cable to the USB-C port of the projector. 2. Connect the other end of the USB Type-C cable to the power bank. NOTE: The power bank should be 45W (15V/3A) at least, and support Power Delivery (PD) protocol output. Additionally, at 15V/3A the projector can be powered on and charge simultaneously.
Connecting to External Devices SD HDMI USB A HDMI HDMI Connection Connect one end of an HDMI cable to the HDMI port of your video device. Then connect the other end of the cable to the HDMI port (supports HDCP 1.4/HDMI 1.4) of your projector. USB Connection USB Type A Connection To enjoy photos, music, and movies, simply plug in a USB flash drive to the USB Type A port. For supported file formats, see page 48. USB-C Connection Connect one end of a USB Type C cable to the USB-C port of your device.
Wireless Screen Mirroring Screen Mirroring provides a 5GHz Wi-Fi connection for users to mirror the screen on their personal device. NOTE: Ensure your device is connected to the same network as the projector. For iOS: 1. Access the drop down control menu. 2. Select the “Screen Mirroring” icon. 3. Choose “ViewSonic PJ-XXXX”. For Android: 1. Download and install the “Google Home” application and open it. 2. Pull-to-refresh the app and wait for 30 seconds. 3.
Connecting to Bluetooth Bluetooth Speaker The projector is equipped with Bluetooth that allows the user to connect their device wirelessly for audio playback. To connect and pair your device: 1. Go to: Home > Bluetooth. 2. Use the Left and Right directional buttons on the remote control to select Bluetooth Speaker or Bluetooth Pairing. Then press OK on the remote control.
3. When the below dialogue box appears, select Yes and press OK on the remote control to enter Bluetooth mode. 4. A sound effect will be audible upon entering pairing mode. 5. Upon successful connection, another sound effect will be audible. NOTE: • Once paired, if both the projector and your device are powered On they will automatically connect via Bluetooth. • The projector’s name will be labeled as “M1+”.
Bluetooth Out Connect the projector to external headphones or speakers that support Bluetooth. To connect and pair your device: 1. Go to: Home > Bluetooth. 2. Use the Left and Right directional buttons on the remote control to select the Bluetooth Out option. 3. The projector will search for nearby Bluetooth devices. Select your device from the list and press OK on the remote control. NOTE: Select the refresh icon and press OK to search for Bluetooth devices again.
Connecting to Networks Wi-Fi Connection To connect to a Wi-Fi network: 1. Go to: Home > Setting > Network Settings > Wi-Fi 2. Press Left or Right on the remote control to select On. 3. Available Wi-Fi networks will then be displayed. Select one of the available Wi-Fi networks.
4. If you connect to a secure Wi-Fi network, you must enter the password when prompted.
Custom SSID 1. Go to: Home > Setting > Network Settings > Wi-Fi 2. Press Left or Right on the remote control to select On. 3. From the available Wi-Fi networks list select Others and press OK on the remote control. 4. Enter the SSID and select the security level.
5. Enter the password when prompted. NOTE: It is recommended to let the system configure the network settings automatically.
Using the Projector Starting Up the Projector 1. Ensure the projector is connected to a power source or that the battery has sufficient charge. 2. Open the Smart Stand by moving its lens cover down. ENTER ENTER 3. Move the Smart Stand to your desired viewing angle.
Adjusting the Projected Image Adjusting the Projector's Height and Projection Angle The projector is equipped with one (1) Smart Stand. Adjusting the stand will change the projector’s height and the vertical projection angle. Carefully adjust the stand to fine tune the projected image’s position. NOTE: • If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image can become trapezoidal.
First Time Activation If the projector is activated for the first time, you will need to select your Preferred Language, Projection Orientation, and Network Settings. Follow the on-screen instructions using the OK and Up/Down/Left/Right buttons on the remote control. When the “Finish screen” appears, this indicates the projector is ready to use. Preferred Language Select the desired language and press OK to confirm the selection.
Projection Orientation Select the preferred projection orientation and press OK to confirm the selection. For more information, see page 12. Network Settings Select one of the available Wi-Fi options. For more information, see page 21.
Shutting Down the Projector 1. Press and hold the Power button for three (3) seconds on the projector, or press the Power button on the remote control. 2. Pressing the Power button on the remote control will result in the following message: 3. Press the Up/Down buttons on the remote control to select Turn Off and press OK on the remote control. NOTE: When not in use, please press the Power button to power off.
Input Source Selected - On-Screen Display (OSD) Tree After your input source is selected, you can adjust the Image Setting and Advanced menus. Main Menu Sub-menu Menu Option Image Setting Color Mode Brightest TV Movie Gaming Brightness (-/+, 0~100) Contrast (-/+, 0~100) Color Temp 6500K 7500K 9300K Tint (-/+, 0~100) Saturation (-/+, 0~100) Sharpness (-/+, 0~100) Gamma 1.8 2.0 2.2 2.35 2.
Main Menu Sub-menu Menu Option Advanced Aspect Ratio Auto 4:3 16:9 Auto HDMI Settings Range Full Limited 3D Settings 3D Sync Auto Off Frame Sequential Frame Packing Top-Bottom Side-by-Side 3D Sync Invert harman/kardon Disable Invert Movie Audio Mode Music User Audio Volume Mute (-/+, 0~20) Off On Full Light Source Level Eco Extended Eco Battery Saving Information Source Ex. HDMI Resolution Ex. 1920 x 1080 @60Hz 3D Format Ex.
Image Setting Menu After your input source is selected, you can adjust the Image Setting menu. To access the Image Setting menu: 1. Press Setting on the remote control. 2. Use the Up/Down buttons to select a menu.
3. Then use the Left/Right buttons to enter the sub-menu(s) and/or adjust the settings. 4. Press the Return button to go to the previous menu or exit.
Menu Option Color Mode Description The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal. Brightest Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, i.e. well-lit rooms. TV Optimized for viewing sports in well-lit environments. Movie Appropriate for colorful movies, video clips from digital cameras, or DVs through the PC input.
Menu Option Tint Saturation Sharpness Gamma Reset Current Color Settings Description The higher the value, the more greenish the picture becomes. The lower the value, the more reddish the picture becomes. Refers to the amount of that color in a video picture. Lower settings produce less saturated colors; in fact, a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.
Advanced Setting Menu After your input source is selected, you can adjust the Advanced menu. To access the Advanced menu: 1. Press Setting on the remote control. 2. Press the Right button to access the Advanced menu.
3. Use the Up/Down buttons to select a menu. 4. Then use the Left/Right buttons to enter the sub-menu(s) and/or adjust the settings. 5. Press the Return button to go to the previous menu or exit.
Menu Option Aspect Ratio Description The aspect ratio is the ratio of the image width to the image height. With the advent of digital signal processing, digital display devices, like this projector, can dynamically stretch and scale the image output to a different aspect than that of the image input signal. NOTE: Only supports HDMI/USB C signal input. Auto Scales an image proportionally to fit the projector’s native resolution in its horizontal width.
Menu Option 3D Settings Description Enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images while wearing 3D glasses. 3D Sync Adjust and choose from: Automatic, Off, Frame Sequential, Frame Packing, Top-Bottom, Side-by-Side. 3D Sync Invert Allows for correction if the 3D image depth is inversed. harman/kardon Adjust the audio settings. Light Source Level Select the suitable power consumption of the LED.
Operating the Projector This section will introduce the Home Screen and its menus. Home Screen The Home Screen is displayed every time you start the projector. To navigate the Home Screen, simply use the directional buttons on the remote control. You can return to the main Home Screen at any time by pressing the Home button on the remote control, regardless of what page you are on. Menu Description File Management Provides a user interface to manage files and folders.
Home Screen - On-Screen Display (OSD) Menu Tree Main Menu File Management Apps Center Bluetooth Sub-menu Menu Option Aptoide Bluetooth Speaker Bluetooth Pairing Bluetooth Out Setting Network Settings Wi-Fi Off On SSID: Configure IP IP Address Subnet Mask Default Gateway DNS Server Others Date & Time Automatic Date & Time Off On Date Time Time Zone Time Format 41 12 Hours 24 Hours
Main Menu Sub-menu Menu Option Setting Basic Settings Language English French German Italian Spanish Russian 繁體中文 簡體中文 日本語 韓語 Swedish Dutch Turkish Czech Portuguese Thai Polish Finnish Arabic Indonesian Hindi Vietnam Greek Front Table Projector Projection Front Ceiling Rear Table Rear Ceiling Keystone Manual (-/+, -40~40) Auto V Keystone Disable Enable 42
Main Menu Sub-menu Setting Advanced Settings Menu Option Home Power On Source HDMI USB-C Power On/Off Ring Tone Off Smart Energy Auto Power Off On Disable 10 minutes 20 minutes 30 minutes Sleep Timer Disable 30 minutes 1 hour 2 hours 3 hours 4 hours 8 hours 12 hours Power Saving Enable Disable harman/kardon Audio Mode Movie Music User Audio Volume (-/+, 0~20) Mute Off On Light Source Level Full Eco Extended Eco Battery Saving 43
Main Menu Sub-menu Menu Option Setting Advanced Settings High Altitude Mode Reset Settings Reset to Factory Default Firmware Upgrade Off On Yes Cancel Yes Cancel Software Update Online Software Update by USB OTA Reminder Enable Disable Software Version Information Light Source Hours System Version Memory Information Wi-Fi Mac Address Serial Number Screen Mirroring Add App Add App Add App Add App 44 XX GB of XX GB Used
Menu Operations File Management Easily manage files and folders. 1. Select: Home > File Management. 2. Select a device on the source list. Use the direction buttons to select the desired file. Then press OK on the remote control to open the selected file. 3. Press the Return button to go to a previous a level. NOTE: Press the Home button on the remote control to return to the Home Screen at anytime.
ement orage How to Edit a File 1. While in File Management, press and hold the OK button for three (3) seconds. 2. A check box will appear at the front of each file. Use the direction buttons and press OK to select one or more files. 13:00 3. By pressing the Right button, Copy, Paste, Cut, Delete, Select All, and Return boxes will be available for use. /Pictures Photo 1-1.png Photo 1-2.png Photo P hotto 1 1-3.png -3 3.png Photo 1-4.png Photo 1-5.png Photo 1-6.png Photo 1-7.png 4.
How to Use the Media Control Bar Buttons The media control bar buttons will appear on screen if a video, music, or photo file are selected to be opened. Picture Video Music Back Back Back Play Rewind Play Next Play Pause Zoom in Pause Next Zoom out Fast Forward Shuffle Rotate (left) Next Repeat All Rotate (right) Repeat One Play List Information NOTE: Tips for Using USB When using USB for reading and/or storage please keep in mind the following: 1.
Supported File Formats Multimedia Formats Extension Type Codec .xvid .avi Video Audio Xvid, H.264 MP3 .mp4 .m4v .mov Video H.264/MPEG-4 Audio AAC Video Video H.264 H.264, MPEG-2 Audio MP3/AAC Video Audio Video MPEG-1, MPEG-2 DVD-LPCM MPEG-1 .mkv .ts .trp .tp .mts .m2ts .vob .mpg Office Formats I. II.
Apps Center View, launch, and uninstall Apps. 1. To view your Apps, select: Home > Apps Center. 2. Use the direction buttons to select the desired App. Then press OK on the remote control to launch the App. NOTE: Press the Home button on the remote control to return to the Home Screen at anytime.
Aptoide The projector is pre-loaded with the Aptoide store, which allows users to download and install different Apps. 1. Select: Home > Apps Center > Aptoide. 2. Use the direction buttons to navigate the menu options. When you find your preferred App, press the OK button to install it. NOTE: • Users can install third-party Apps by .apk file in File Management. However, some third-party Apps may have compatibility issues. • Apps not pre-loaded by ViewSonic may not be compatible or work properly.
To Uninstall Apps 1. Open the Apps Center by selecting: Home > Apps Center. 2. Use the directional buttons to select the desired App. 3. Press and hold OK on the remote control for three (3) seconds. The below dialogue box will appear: 4. Select OK to uninstall the App. NOTE: Press the Home button on the remote control to return to the Home Screen at anytime.
Bluetooth The projector is equipped with Bluetooth that allows the user to connect their device wirelessly for audio playback. For more information, see “Connecting to Bluetooth” on page 18page 18.
Setting Under Setting you can adjust Network, Basic, and Advanced Settings, Date & Time, Firmware Update, and view Information. Network Settings 1. Select: Home > Setting > Network Settings.
2. View and adjust your Wi-Fi and network settings. 3. To setup a Wireless connection, see “Connecting to Networks” on page 21page 21.
Basic Settings 1. Select: Home > Setting > Basic Settings. 13:00 Network Settings Firmware Update Basic Settings Advanced Settings Date & Time Information 2. Use the Up and Down buttons to select the desired option and press OK. Then use the Left and Right buttons to make adjustments or selections. 3. To return to a previous menu press the Return button. Menu Language Projector Position Description Select your desired language. Select the preferred projection position.
Menu Keystone Description Adjust trapezoidal screen image distortion. Manual Keystone can be adjusted manually from -40 to 40. Auto V Keystone Provides a rectangular screen image by automatically adjusting the keystone number when there is a trapezoidal screen image caused by the tilting of the projector. • Enable: Automatically adjust the keystone number. • Disable: Manually adjust the keystone number. NOTE: If Manual is selected, Auto V Keystone will change to Disable automatically.
Date & Time Adjust Date, Time, Time Zone, and Time Format. NOTE: The time is displayed in the top-right corner after connecting to the Internet. 1. Select: Home > Setting > Date & Time. 13:00 Network Settings Basic Settings Firmware Update Advanced Settings Date & Time Information 2. Use the Up and Down buttons to select the desired option and press OK. Then use the Left and Right buttons to make adjustments or selections.
Menu Automatic Date & Time Description Users can synchronize the date and time automatically after connecting to the Internet. On Turn on synchronization. Time Zone Off Turn off synchronization. Select your desired location. Time Format Select a different display time format. 12 Hours 12-hour clock. 24 Hours 24-hour clock.
Firmware Upgrade Users can update the firmware Online, or by USB, and check the version number. NOTE: Do not unplug the power cord, USB, or disconnect from the Internet during the upgrading process. 1. Before entering the Firmware Upgrade menu, ensure the projector is connected to the Internet. 2. To enter the menu, select: Home > Setting > Firmware Upgrade.
Firmware Update Online 1. Go to: Home > Setting > Firmware Upgrade > Software Update Online. 2. Select Enter by pressing OK on the remote control. 3. The system will check the ViewSonic website (OTA) and display the below dialog message if their is new Firmware. 4. By selecting Yes, a progress bar will appear as the update process begins. UPGRADING SOFTWARE PLEASE DO NOT TURN OFF 52% 5. Upon reaching 100%, the projector will restart and the screen will turn to black for a few minutes.
Firmware Update by USB 1. Download the latest version from the ViewSonic website and copy the file to a USB device. 2. Plug the USB into the projector, then go to: Home > Setting > Firmware Upgrade > Software Update By USB. 3. Select Enter by pressing OK on the remote control. 4. The system will detect the Firmware version and display the above dialog message. 5. By selecting Yes, a progress bar will appear as the update process begins. 6.
Advanced Settings 1. Select: Home > Setting > Advanced Settings. 13:00 Network Settings Firmware Update Basic Settings Advanced Settings Date & Time Information 2. Use the Up and Down buttons to select the desired option and press OK. Then use the Left and Right buttons to make adjustments or selections. 3. To return to a previous menu press the Return button.
Menu Power On Source Power On/Off Ring Tone Smart Energy Description Allows the user to enter the desired source directly after turning on the projector. Enable or disable the power on/off ring tone. Auto Power Off The projector can turn off automatically after a set period of time once no input source is detected. Sleep Timer Turn off automatically after a set period of time. Power Saving Lower power consumption if no input source is detected after five (5) minutes.
Menu Light Source Level Description Select the suitable power consumption of the LED. Mode Full Eco Extended Eco Battery Saving High Altitude Mode Reset Settings Power Consumption 100% 70% 55% 30% It is recommended that you use High Altitude Mode when your environment is between 1,5003,000 m above sea level, and a temperature between 5°C-25°C.
Menu Reset to Factory Default Description Factory reset. NOTE: Light Source Hours will remain unchanged.
Information 1. Select: Home > Setting > Information. 13:00 Network Settings Basic Settings Firmware Update Advanced Settings Date & Time Information 2. View system status and information. NOTE: Press the Home button on the remote control to return to the Home Screen at anytime.
Screen Mirroring Mirror your personal device’s screen. To setup wireless Screen Mirroring, see “Wireless Screen Mirroring” on page 17page 17. NOTE: Ensure your device is connected to the same network as the projector.
Adding Apps Add your favorite Apps to the Home Screen. 1. From the Home Screen, select Add App and then press OK on the remote control. 2. Use the directional buttons to select the desired App and press OK.
3. Now your favorite App will appear on the Home Screen. Delete Apps From the Home Screen 1. From the Home Screen, select the App you want to delete and press and hold OK for three (3) seconds. 2. The message, “Do you want to Delete this application from My Favorites?” will appear. 3. Select Yes, and press OK to delete the App.
Appendix Specifications Item Category Specifications Projector Type 0.2” WVGA, LED Display Size Throw Distance Lens 24”~100” 0.64-2.66 m (38”@1 m) F=1.7, f=5.5 mm Optical Zoom Fixed Light Source Type Light Source Life (Normal) Display Color Keystone Battery Capacity RGB LED Input Signal Resolution Input Ouput Power Adapter Local Storage Operating Conditions Dimensions Weight Power Saving Modes up to 30,000 hours HDMI 1.07 Billion Colors -/+ 40 (Vertical) 12,000 mAh, 3.
Timing Chart HDMI/USB C Video Timing Timing Resolution Horizontal Frequency (kHz) 480i 480p 576i 576p 720/50p 720/60p 1080/24P 1080/25P 1080/30P 1080/50i 1080/60i 1080/50P 1080/60P 720(1440) x 480 15.73 59.94 27 720 x 480 31.47 59.94 27 720(1440) x 576 15.63 50 27 720 x 576 31.25 50 27 1280 x 720 37.5 50 74.25 1280 x 720 45 60 74.25 1920 x 1080 27 24 74.25 1920 x 1080 28.13 25 74.25 1920 x 1080 33.75 30 74.25 1920 x 1080 28.13 50 74.25 1920 x 1080 33.75 60 74.
HDMI/USB C Support PC Timing Resolution 640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 768 1280 x 800 1280 x 960 1280 x 1024 1360 x 768 1400 x 1050 1440 x 900 1600 x 1200 1680 x 1050 Refresh Rate (Hz) Horizontal Frequency (kHz) Dot Clock Frequency (MHz) 59.94 31.469 25.175 72.809 37.861 31.5 75 37.5 31.5 70.087 31.469 28.3221 56.250 35.156 36 60.317 37.879 40 72.188 48.077 50 75 46.875 49.5 60.004 48.363 65 70.069 56.476 75 75.029 60.023 78.75 75 67.
3D Support Timing HDMI 3D (BlueRay 3D with info frame) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) Support Frame Packing 1080p 1920 x 1080 16:9 23.98/24 Yes 720p 1280 x 720 16:9 50/59.94/60 Yes 50/59.94/60 Yes Side by Side 1080i 1920 x 1080 16:9 Top and Bottom 1080p 1920 x 1080 16:9 23.98/24 Yes 720p 1280 x 720 16:9 50/59.
LED Indicators Light Description Green Red Flashing White Solid White Power On Stand-by Mode Projector Charging Battery is Fully Charged 74
Troubleshooting This section describes some common problems that you may experience when using the projector. Problem or Issue Possible Solutions The projector does not • Ensure the power cord is properly attached to the turn on projector and to the power outlet. • If the cooling process has not completed, please wait until it has finished then try to turn on the projector again. • If the above does not work, try another power outlet or another electrical device with the same power outlet.
Problem or Issue The projector/system is frozen and will not respond Possible Solutions • Please toggle the Power Switch off/on to reset the device.
Maintenance General Precautions • Make sure the projector is turned off and the power cable is unplugged from the power outlet. • Never remove any parts from the projector. Contact ViewSonic® or a reseller when any part of the projector needs replacing. • Never spray or pour any liquid directly onto the case. • Handle the projector with care, as a darker-colored projector, if scuffed, may show marks more clearly than a lighter-colored projector.
Regulatory and Service Information Compliance Information This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit. FCC Compliance Statement This device complies with part 15 of FCC Rules.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
IC Radiation Exposure Statement This equipment complied with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The device for the band 5150-5825 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Lead (Pb) Proposed Maximum Actual Concentration Concentration Mercury (Hg) Cadmium
ͫ High or low extreme temperatures that a battery can be subjected to during use, storage or transportation; and low air pressure at high altitude.
Copyright Information Copyright© ViewSonic® Corporation, 2020. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Customer Service For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product’s serial number. Country/ Region Website Country/ Region Website Asia Pacific & Africa Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/ 中国 (China) www.viewsonic.com.cn 香港 (繁體中文) www.viewsonic.com/hk/ Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/ Indonesia www.viewsonic.com/id/ Israel www.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic® will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
ͫ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. ͫ Operation outside of product specifications. ͫ Operation of the product for other than the normal intended use or not under normal conditions. ͫ Repair or attempted repair by anyone not authorized by ViewSonic®. ͫ Any damage of the product due to shipment. ͫ Removal or installation of the product.
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic® shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages. 2.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic® will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
How to get service: For information about receiving service under warranty, contact ViewSonic® Customer Support (Please refer to the attached “Customer Service” page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.
Process Color C0 M91 Y72 K24 Process Color C0 M0 Y0 K100 Process Color C0 M91 Y72 K24 Spot Color Pantone Black C Spot Color Pantone 187 C